Roland Professional A/V XI-DVI Users Manual
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
* 5 1 0 0 0 5 4 8 2 9 - 0 1 *
on back side. After reading, keep the document(s) where it will be available for immediate
reference.
Copyright © 2016 ROLAND CORPORATION
Setup Guide
Panel Descriptions
1 2
3
4
Thank you, and congratulations on your choice of the XI-DVI expansion
interface.
Installing the XI-DVI in a professional video device from Roland lets you
expand DVI input and output.
For information on devices on which the XI-DVI expansion interface can
be installed, check the Roland website.
http://proav.roland.com
No. Name Explanation
These function as either DVI input or DVI output. You use the
device where the XI-DVI is installed to specify the operation of
DVI-I IN/DVI-D OUT 1, 2
1
connectors
POWER indicator This lights up when the XI-DVI is receiving power.
2
USB port
3
Ventilation holes
4
the respective connectors (input or output).
The following signals are supported.
DVI input: Analog RGB, analog component, DVI-D, and HDMI
DVI output: DVI-D and HDMI
This is a dedicated connector for updating the XI-DVI.
* Do not use a micro USB cable that is designed only for
charging a device. Charge-only cables cannot transmit data.
These inhibit temperature rises inside the XI-DVI by taking in
outside air and venting inner air.
NOTE
Never block the ventilation holes. Using the device with the
ventilation holes obstructed can result in internal heat buildup
and danger of malfunction of the XI-DVI.
Installing the XI-DVI
Install the XI-DVI on a compatible device.
Important Notes on Handling
Touching corners, protrusions, or other sharp areas on the XI-DVI can result in injury. Use
ample care when handling.
To avoid the risk of damage to internal components that can be caused by static
electricity, please carefully observe the following whenever you handle the XI-DVI.
• Before you touch the XI-DVI, always rst grasp a metal object (such as a water pipe),
so you are sure that any static electricity you might have been carrying has been
discharged.
• When handling the XI-DVI, grasp it only by the panel or the XI-DVI’s edges. Avoid
touching any of the electronic components or connectors.
• Before you connect any cables, make sure they do not carry a static electricity
charge. Such charges can be transmitted, for example, if the other end of the cable
has been in contact with a carpet (or other object) where there is a static electricity
buildup.
• Save the bag in which the XI-DVI was originally shipped, and put the XI-DVI back
into it whenever you need to store or transport it.
Installing
NOTE
• Before installing the XI-DVI, you must rst always turn o the unit where installing
and unplug its power cord from the power outlet.
• When restarting the device with the XI-DVI installed, wait several seconds before
turning on the power.
1. Loosen the EXPANSION SLOT mounting screws (2) on the device where you’re
installing, and detach the panel cover.
2. Insert the XI-DVI into the EXPANSION SLOT.
* Do not touch any of the XI-DVI pathways or connection terminals.
* Never use excessive force when installing the XI-DVI. If it doesn’t t properly on the rst
attempt, remove the XI-DVI and try again.
3. Secure the XI-DVI in place using the mounting screws (2).
Main Speci cations
Roland XI-DVI: DVI EXPANSION INTERFACE
Video
Processing 4:2:2 (Y/Pb/Pr), 10 bits
DVI-I/HDMI: DVI-I type x 2
Input/Output Connectors
Formats
E ects
Audio
Processing Sampling Rate: 24 bits/48 kHz
Input/Output Connectors HDMI: DVI-I type x 2
Formats Linear PCM, 24 bits, 48 kHz, 8 ch
Others
Other connectors USB port: USB Micro-B type x 1 * for System update.
Power Consumption 30 W
Operation Temperature
Dimensions
Weight
Accessory Setup guide
* This document explains the speci cations of the product at the time that the document
was issued. For the latest information, refer to the Roland website.
* Bidirectional.
* Analog RGB/Analog component is supported input only.
* HDCP is not supported.
480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p,
1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p, 1024 x 768/60 (*1),
1280 x 720/60 (*1), 1280 x 800/60 (*1), 1366 x 768/60 (*1),
1280 x 1024/60 (*1), 1400 x 1050/60, 1600 x 1200/60,
1920 x 1080/60, 1920 x 1200/60
* Conforms to CEA-861-E, VESA DMT Version 1.0 Revision 11
* Frame rate is 59.94 Hz (NTSC) or 50 Hz (PAL).
(*1) Output refresh rate is 75 Hz when frame rate is set to 50 Hz.
Scaler x 2
* Format Conversion, Manual Scaling
+5 to +40 degrees Celsius
+41 to +104 degrees Fahrenheit
120 (W) x 185 (D) x 40 (H) mm
4-3/4 (W) x 7-5/16 (D) x 1-5/8 (H) inches
* Protruding parts not included.
280 g
10 oz
4
* When the XI-DVI installation is complete, double-check your work.
For the USA
ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUMImporter:
USING THE UNIT SAFELY
ALWAYS OBSERVE THE FOLLOWING
For China
For EU Countries
About WARNING and CAUTION Notices
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless
you are instructed to do so in the
Setup Guide. Otherwise, you risk
causing malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer,
the nearest Roland Service Center,
or an authorized Roland distributor,
as listed on the “Information.”
Do not use or store in the following types of
locations
• Subject to temperature
extremes (e.g., direct sunlight
in an enclosed vehicle, near a
heating duct, on top of heatgenerating equipment); or are
• Damp (e.g., baths, washrooms,
on wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness; or are
• Placed in a poorly ventilated location.
Do not allow foreign objects or liquids to
enter unit; never place containers with liquid
on unit
Do not place containers containing
liquid (e.g., ower vases) on this
product or the device on which
it is installed. Never allow foreign
objects (e.g., ammable objects,
coins, wires) or liquids (e.g., water
or juice) to enter this product.
Doing so may cause short circuits, faulty
operation, or other malfunctions.
Turn o the unit if an abnormality or
malfunction occurs
Immediately turn the unit o , and
request servicing by your retailer,
the nearest Roland Service Center,
or an authorized Roland distributor,
as listed on the “Information” when:
Do not drop or subject to strong impact
Otherwise, you risk causing
damage or malfunction.
Turn the unit o before installing expansion
interfaces
Before installing the expansion
interface (XI-DVI), you must rst
always turn o the unit where
installing and unplug its power
cord.
About the Symbols
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
WARNING
• If smoke or unusual odor occurs; or
• Objects have fallen into, or liquid has
been spilled onto the unit; or
• The unit has been exposed to rain (or
otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked change in
performance.
CAUTION
Route all cables in such a way as to prevent
them from getting entangled
Injury could result if someone were
to trip on a cable and cause the
installed device to fall or topple.
Avoid climbing on top of the unit, or placing
heavy objects on it
Otherwise, you risk injury as the
result of the unit toppling over or
dropping down.
Disconnect all cords/cables before moving
the unit
Damage or malfunction may result
if you fail to disconnect all cables
before moving the unit.
Install expansion interface(s) only in
speci ed units
Install the expansion interface
only into the speci ed unit (a
device compatible with the XI-DVI).
Remove only the speci ed screws
during the installation.
IMPORTANT NOTES
Placement
• This unit may interfere with radio and
television reception. Do not use this unit in
the vicinity of such receivers.
• When moved from one location to
another where the temperature and/or
humidity is very di erent, water droplets
(condensation) may form inside the unit.
Damage or malfunction may result if you
attempt to use the unit in this condition.
Therefore, before using the unit, you must
allow it to stand for several hours, until the
condensation has completely evaporated.
• Do not place containers or anything else
containing liquid on top of this unit. Also,
whenever any liquid has been spilled on
the surface of this unit, be sure to promptly
wipe it away using a soft, dry cloth.
Maintenance
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility
of discoloration and/or deformation.
Additional Precautions
* Use a reasonable amount of care when
using the unit’s buttons, sliders, or other
controls; and when using its jacks and
connectors. Rough handling can lead to
malfunctions.
* When disconnecting all cables, grasp the
connector itself—never pull on the cable.
This way you will avoid causing shorts, or
damage to the cable’s internal elements.
* To prevent malfunction and equipment
failure, always turn down the volume, and
turn o all the units before making any
connections.
Intellectual Property Right
• It is forbidden by law to make an audio
recording, video recording, copy or
revision of a third party’s copyrighted work
(musical work, video work, broadcast, live
performance, or other work), whether
in whole or in part, and distribute, sell,
lease, perform or broadcast it without the
permission of the copyright owner.
• Do not use this product for purposes
that could infringe on a copyright
held by a third party. We assume no
responsibility whatsoever with regard to
any infringements of third-party copyrights
arising through your use of this product.
• This product contains eParts integrated
software platform of eSOL Co.,Ltd. eParts is
a trademark of eSOL Co., Ltd. in Japan.
• Roland is an either registered trademark
or trademark of Roland Corporation in the
United States and/or other countries.
• Company names and product names
appearing in this document are registered
trademarks or trademarks of their
respective owners.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
To assure continued FCC emission limit compliance, use only shielded interface cables when connecting to other device.
Any unauthorized changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
For Canada
CAN ICES-3 (A)/NMB-3 (A)
For Korea
For C.A. US (Proposition 65
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
Manufacturer:
For EU Countries
2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN
This product is intended for use in the following Electromagnetic environments:
E4: controlled EMC environment,
ex. broadcasting studio which are specied in EN55103-1 and EN55103-2.
Warning: Operation of this product in the other Electromagnetic environments could cause radio interference.
)
Loading...