Roland Professional A/V AR-200R Users Manual
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 2–3, p. 4). These sections provide
important information concerning the proper operation of the unit. Additionally,
in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner's manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
Copyright © 2006 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
USING THE UNIT SAFELY
BLUE:
BROWN:
NEUTRAL
LIVE
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
..........................................................................................................
002c
• Do not open (or modify in any way) the unit or its
AC adaptor.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
005
• This unit should be used only with a rack mount
adaptor (RAD-50) that is recommended by
Roland.
..........................................................................................................
006
• When using the unit with a rack or stand recommended by Roland, the rack or stand must be
carefully placed so it is level and sure to remain
stable. If not using a rack or stand, you still need
to make sure that any location you choose for
placing the unit provides a level surface that will
properly support the unit, and keep it from
wobbling.
..........................................................................................................
008c
• Be sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified on
the AC adaptor’s body. Other AC adaptors may
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
..........................................................................................................
008d
• Take care not to exceed the maximum rated specifications (100 mA) when using the DC OUT
terminal for the power supply.
..........................................................................................................
008e
• Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
..........................................................................................................
2
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements
and short circuits. Damaged cords are fire and
shock hazards!
..........................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the unit.
..........................................................................................................
012b
• Immediately turn the power off, remove the AC
adaptor from the outlet, and request servicing by
your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on
the “Information” page when:
• The AC adaptor, the power-supply cord, or the
plug has been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally
or exhibits a marked change in performance.
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
101b
• The unit and the AC adaptor should be located so
their location or position does not interfere with
their proper ventilation.
..........................................................................................................
102c
• Always grasp only the plug on the AC adaptor
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103b
• At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor insulation
and lead to fire.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107c
• Never handle the AC adaptor or its plugs with
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
108b
• Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..........................................................................................................
109b
• Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet (p. 9).
..........................................................................................................
110b
• Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
..........................................................................................................
118c
• Keep any screw terminals, the ground terminal
screw, you may remove and the included
Euroblock connector, rubber feet, and card
protector attachment screws in a safe place out of
children’s reach, so there is no chance of them
being swallowed accidentally.
..........................................................................................................
3
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2–3, please read and observe the
following:
Power Supply
301
• Do not connect this unit to same electrical outlet that is being used
by an electrical appliance that is controlled by an inverter (such as a
refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which
the electrical appliance is used, power supply noise may cause this
unit to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a power supply
noise filter between this unit and the electrical outlet.
302
• The AC adaptor will begin to generate heat after long hours of
consecutive use. This is normal, and is not a cause for concern.
307
• Before connecting this unit to other devices, turn off the power to
all units. This will help prevent malfunctions and/or damage to
speakers or other devices.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or move it
farther away from the source of interference.
352a
• This device may interfere with radio and television reception. Do
not use this device in the vicinity of such receivers.
352b
• Noise may be produced if wireless communications devices, such
as cell phones, are operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call, or while conversing.
Should you experience such problems, you should relocate such
wireless devices so they are at a greater distance from this unit, or
switch them off.
355b
• When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation)
may form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using
the unit, you must allow it to stand for several hours, until the
condensation has completely evaporated.
360
• Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar the
surface.
You can place a piece of felt or cloth under the rubber feet to
prevent this from happening. If you do so, please make sure that
the unit will not slip or move accidentally.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth or one
that has been slightly dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild, non-abrasive detergent.
Afterwards, be sure to wipe the unit thoroughly with a soft, dry
cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Additional Precautions
552
• Unfortunately, it may be impossible to restore the contents of data
that was stored memory card once it has been lost. Roland Corporation assumes no liability concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and connectors.
Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
558a
• To avoid disturbing your neighbors, try to keep the unit’s volume
at reasonable levels. You may prefer to use headphones, so you do
not need to be concerned about those around you (especially when
it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise, you will
need to use equivalent packaging materials.
562
• Some connection cables contain resistors. Do not use cables that
incorporate resistors for connecting to this unit. The use of such
cables can cause the sound level to be extremely low, or impossible
to hear. For information on cable specifications, contact the
manufacturer of the cable.
Before Using Cards
Using Memory Cards
704
• Carefully insert the DATA card all the way in—until it is firmly in
place.
fig.M512-Insert.eps
CompactFlash™
705
• Never touch the terminals of the DATA card. Also, avoid getting
the terminals dirty.
707
• This unit’s memory card slot accepts CompactFlash memory cards.
Microdrive storage media are not compatible.
708
• CompactFlash cards are constructed using precision components;
handle the cards carefully, paying particular note to the following.
• To prevent damage to the cards from static electricity, be
sure to discharge any static electricity from your own
body before handling the cards.
• Do not touch or allow metal to come into contact with
the contact portion of the cards.
• Do not bend, drop, or subject cards to strong shock or
vibration.
• Do not keep cards in direct sunlight, in closed vehicles,
or other such locations (storage temperature: -25 to 85˚
C).
• Do not allow cards to become wet.
• Do not disassemble or modify the cards.
Copyright
851
• Recording, duplication, distribution, sale, lease, performance, or
broadcast of copyrighted material (musical works, visual works,
broadcasts, live performances, etc.) belonging to a third party in
part or in whole without the permission of the copyright owner is
forbidden by law.
853
• Do not use this unit for purposes that could infringe on a copyright
held by a third party. We assume no responsibility whatsoever
with regard to any infringements of third-party copyrights arising
through your use of this unit.
4
Contents
USING THE UNIT SAFELY ..............................................................................2
IMPORTANT NOTES........................................................................................4
Main Features ..................................................................................................7
Panel Descriptions ..........................................................................................8
Important Notes on Making Connections and Switching the Power On and Off ....9
Turning On the Power.................................................................................................................................................. 9
Installation......................................................................................................10
Attaching the Rubber Feet (Included Items)........................................................................................................... 10
Rack Mounting (Important Notes on Heat Radiation).......................................................................................... 10
Attaching the Card Protector .................................................................................................................................... 11
Examples of Usage and Connection for the AR-200R ...............................12
Together with Other Equipment (System Examples)............................................................................................ 12
Using the Control Input and Output Connectors...................................................................................... 12
Using the MIDI Connectors .......................................................................................................................... 13
What You Can Do (Usage Tips) ................................................................................................................................ 14
Repeat Playback of the Same Phrase ........................................................................................................... 14
Playing a Variety of Phrases in Succession................................................................................................. 14
Cards Handled by the AR-200R....................................................................15
Types of Usable Cards................................................................................................................................................ 15
Card Storage Times and Number of Phrases.......................................................................................................... 15
Formatting a Card....................................................................................................................................................... 15
Important Notes on Handling Cards ....................................................................................................................... 16
Card Compatibility with Other Models in the AR Series ..................................................................................... 17
Recording Audio............................................................................................18
Recording Units—Phrases............................................................................................................................. 18
Connecting External Devices ........................................................................................................................ 18
Procedure for Recording ............................................................................................................................................ 19
Required Settings for Recording Audio Signals (Recording Settings) ................................................... 19
Procedure......................................................................................................................................................... 22
Checking What You Recorded .................................................................................................................................. 23
Information Recorded on the Card.............................................................................................................. 23
Playback Using the Panel (Manual Playback).............................................24
Deleting Phrases ...........................................................................................25
Deleting Single Phrases ................................................................................................................................. 25
Deleting All Phrases....................................................................................................................................... 25
Recording and Playing MIDI Data (MIDI Phrase) ........................................26
What is a MIDI Phrase? ................................................................................................................................. 26
Connecting External Devices ........................................................................................................................ 26
Procedure for Recording MIDI Phrases ...................................................................................................... 26
Procedure for Playing Back MIDI Phrases.................................................................................................. 27
Controlling the AR-200R from an External Device (Control Input Connectors) ....28
What Is No-voltage/Make-contact? ............................................................................................................ 28
Types of Control Input Playback ................................................................................................................. 28
Types of Control Input Recording ............................................................................................................... 28
Playback By Card Data............................................................................................................................................... 28
Cards Created on the AR-3000R/3000/2000.............................................................................................. 28
Card made on the AR-200R/200S/200/100 ............................................................................................... 28
AR-200R Settings ............................................................................................................................................ 29
Playing Back Phrases Assigned to the Connectors (Direct Playback)................................................................. 30
Connecting External Devices ........................................................................................................................ 30
Operational Specifications for Direct Playback (Last-In).......................................................................... 30
AR-200R Settings ............................................................................................................................................ 31
5
Contents
Specifying Phrases in Binary Notation (Binary Playback).................................................................................... 31
What Is Binary Playback?/Use and Applications ..................................................................................... 31
Connecting External Devices ........................................................................................................................ 31
Operational Specifications of Binary Playback .......................................................................................... 32
AR-200R Settings ............................................................................................................................................ 32
To Specify Phrases with Binary Signals ...................................................................................................... 32
Phrase Number / Binary Signal chart ......................................................................................................... 33
Repeated Playback of Phrases (Interval Playback) ................................................................................................ 34
Operational Specifications of Interval Playback ........................................................................................ 34
AR-200R Settings ............................................................................................................................................ 34
Controlling Recording with the Control Connectors (Binary Rec)...................................................................... 34
What is Binary Rec/Use and Applications................................................................................................. 34
Connecting Equipment.................................................................................................................................. 35
Operational Specifications for Binary Rec .................................................................................................. 35
AR-200R Settings ............................................................................................................................................ 36
To Specify Phrases with Binary Signals ...................................................................................................... 37
Controlling Another Device with the AR-200R (Control Output Connectors) .......38
Starting Another Device (Busy Out)......................................................................................................................... 38
Controlling Another Device (Control Out) ............................................................................................................. 39
Applications Guide (For Use in Conjunction with the AR-3000R/3000)
Controlling the AR-200R with MIDI Signals (MIDI Control)........................42
What is MIDI Control?/What You Can Do Using MIDI Control ........................................................... 42
Playback of Phrases Using MIDI Signals................................................................................................................. 42
Connecting External Devices ........................................................................................................................ 43
Assignment of Phrases to Note Numbers (MIDI Note Map)................................................................... 43
AR-200R Settings ............................................................................................................................................ 44
Synchronized Recording and Playback with Multiple AR Units (AR-LINK) ...........45
Other Useful Functions During Phrase Playback.......................................47
Playing Data for Two Units on the Left and Right (Dual Mono Mode)................................................. 47
Line Out (Thru) Setting During Phrase Playback...................................................................................... 47
Adjusting the Sound Quality During Audio Phrase Playback (EQ–Equalizer).................................... 48
Playing Back Phrases in the Order They Are Selected (Program Playback).......................................... 48
Appendices
Troubleshooting ............................................................................................50
Error messages .............................................................................................52
Regarding Cards............................................................................................53
Card-specific Audio Recording Time Chart............................................................................................................ 53
Recorded Phrase Data ................................................................................................................................................ 54
Settings When a Card Is Formatted.......................................................................................................................... 54
AR-3000R/3000 settings that can be used ............................................................................................................... 55
MODE SW Settings........................................................................................56
Control I/O Connector specifications ..........................................................57
MIDI Implementation .....................................................................................58
MIDI Implementation Chart ...........................................................................64
Specification ..................................................................................................66
Index ...............................................................................................................69
6
Main Features
High-quality Recording and Playback
Thanks to Roland’s innovative RDAC system, you can enjoy high-quality, recording and playback using less data. You can select
recording settings that suit the situation and the capacity of the card (sampling frequency: 6 levels, recording mode: 4 levels). This
ensures support for recording and playback in a variety of situations and uses.
What you record and the settings are all saved on the card, so you can change situations rapidly simply by changing cards. The
AR-200R can record and play back up to a maximum of 250 phrases (using cards created on Roland’s AR-3000R/3000/200S
allows playback of up to 1000 phrases).
Audio Recording System with No Moving Parts
An audio recording system that uses CF cards and has no moving parts is employed. The system has no rotating parts or drive
mechanism, so it’s practically maintenance free. It provides excellent sound quality and superior reliability.
A Variety of Control Jacks for a Wide Range of Playback Methods
As connectors to use for control, the unit features a Control In jack, MIDI connectors, and AR-LINK connectors. This lets you
select from a variety of playback methods and create systems matched to usage and situations.
Compact Body for Easy Portability
The compact half-rack size body takes little space, and can be conveniently transported. If a separately sold RAD-50 rack mount
adaptor is used, the AR-200R can be installed in an EIA rack.
MIDI Connectors Allow for Play of Musical Instruments and Syncing with Video
Since the unit is equipped with MIDI connectors, you can record and play back MIDI signals. You can play an electronic musical
instrument automatically, just like playing back an audio phrase.
Control of recording/playback using MIDI signals is also supported. This means you can use MTC and MMC signals to obtain
recording/playback that is synchronized to video and other external devices.
Multi-track Operation–AR-LINK Feature
The AR-LINK feature lets you link the unit to up to 31 other units to create a completely synchronized multi-track system.
The AR-3000R/3000 is required as a master control device.
Capable of DC-Powered Operation
Since external DC power supply is also supported, a wide variety of applications are possible.
7
Panel Descriptions
fig.kakubu
Front Panel
Rear Panel
Bottom Chassis
Front panel
1.
PHONES jack
2.
MIDI/CLIP indicator
3.
SLAVE Indicator
4.
Display
5.
PLAY button
6.
PLAY indicator
7.
STOP button
8.
Decrement ( ) button
9.
Increment ( ) button
10.
MEMORY FULL indicator
11.
CARD slot
12.
Eject button
Rear panel
13.
OUTPUT jacks
14.
INPUT jacks
16.
Control input and DC input terminal (CONT A)
* The terminal/connector section features a protective cover.
Whenever you remove this cover, such as when making
connections to the connectors, make sure not to lose it.
Additionally, keep the cover out of the reach of children.
17.
Control I/O connector (CONT B)
* This is not an RS-232C type connector.
18.
MIDI OUT/THRU connector
This is normally used as a MIDI OUT connector. However,
by using a card with settings made on an AR-3000R/3000 or
ARE-3000, this can also function as a MIDI THRU connector.
19.
GND terminal
20.
MIDI IN connector
21.
AR-LINK Connectors (OUT and IN)
22.
Power connector (for supplied AC adaptor)
Bottom chassis
23.
REC MODE switches
24.
MODE switches
15.
INPUT VOLUME
8
mportant Notes on Making Connections
I
and Switching the Power On and Off
• To prevent malfunction and/or damage to speakers
or other devices, always turn down the volume, and
turn off the power on all devices before making any
connections.
• This instrument is equipped with balanced (TRS)
type jacks. Wiring diagrams for these jacks are
shown below. Make connections after first checking
the wiring diagrams of other equipment you intend
to connect.
fig.XLR/TRSJack.eps
• When connection cables with resistors are used, the
volume level of equipment connected to the inputs
(INOUT jacks) may be low. If this happens, use
connection cables that do not contain resistors.
• Depending on the circumstances of a particular
setup, you may experience a discomforting
sensation, or perceive that the surface feels gritty to
the touch when you touch this device, microphones
connected to it, or the metal portions of other objects,
such as guitars. This is due to an infinitesimal
electrical charge, which is absolutely harmless.
However, if you are concerned about this, connect
the ground terminal (see figure) with an external
ground. When the unit is grounded, a slight hum
may occur, depending on the particulars of your
installation. If you are unsure of the connection
method, contact the nearest Roland Service Center,
or an authorized Roland distributor, as listed on the
“Information” page.
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be
dangerous in the event of lightning)
• Once the connections have been completed, turn on
power to your various devices in the order specified.
By turning on devices in the wrong order, you risk
causing malfunction and/or damage to speakers and
other devices.
(When turning the power off, reverse this procedure.)
• This unit is equipped with a protection circuit. A
brief interval (a few seconds) after power up is
required before the unit will operate normally.
• To avoid risk of electric shock, do not touch the
connectors while the unit is in operation.
• Never remove a card during recording of phrases.
Furthermore, do not turn off the power or remove
the AC adaptor cord during recording of phrases.
Doing so may damage the card.
• To avoid the risk of malfunction and/or damage,
insert only CF Card into the disk drive. Never insert
any other type of disk. Avoid getting paper clips,
coins, or any other foreign objects inside the drive.
• The pin assignment for the connectors is as shown
below. Before making any connections, make sure
that this pin assignment is compatible with that of all
your other devices.
GND(SLEEVE)
HOT(TIP)
COLD(RING)
With balanced output
GND(SLEEVE)
HOT(TIP)
With unbalanced output
Turning On the Power
The AR-200R is not equipped with a power switch.
Power is turned on when electricity is supplied to the
power connector (for the supplied AC adaptor), or to the
control input and DC input, or control I/O connectors’
DC IN (p. 8).
Supplied AC adaptor: PSB-1U
Control input and DC input/control I/O connector
specifications
Voltage: 9 to 24 V DC
Current: 1200 mA
* Refer also to “
Do not supply electrical power simultaneously to multiple
connectors or terminals; doing so may result in damage to the
unit.
DC power supply”
(p. 57).
Connected device → AR-200R → Power amp, etc.
9
Installation
Attaching the Rubber Feet (Included Items)
Attach these as required, such as when you’re using the AR-200R without mounting
it on a rack or the like.
Peel off the double-sided tape from the rubber feet and affix the rubber feet at the
locations shown in the following figure.
fig.set-01
Bottom Chassis
Rack Mounting (Important Notes on Heat Radiation)
When you are mounting the unit on a rack or the like, give attention to the following
points to ensure efficient cooling.
• Install in a well-ventilated location.
• Avoid mounting in a sealed rack. Warm air within the rack cannot escape
and is sucked into the unit again, making efficient cooling impossible.
• When you are using a stacked mounting arrangement, be especially sure
to provide for adequate ventilation within the rack to keep discharged air
from being sucked back into the unit. If the back surface of the rack cannot
be kept open, then provide a ventilation port or ventilation fan at the
upper area of the back surface of the rack, where warm air accumulates.
• When you are using the unit in a portable case or rack, remove the covers
from the front and back surfaces of the case, so that the front and back
surfaces of the unit are not obstructed.
• If an error message informing you of a dangerous rise in temperature
appears (p. 52), then heat-dissipating measures are needed. Refer to the
cautions just described and check the installed state of the unit and the
rack.
10
* When placing the unit on the rack, be careful not to pinch your fingers.
* For more information about installation, also see
(p. 4).
“Placement”
in the Usage Notes
Rack-Mounting the AR-200R
By attaching a rack mount adaptor to the AR-200R (RAD-50: sold separately) you can
install it in an EIA rack. One RAD-50 can accommodate up to two AR-200R units.
1
Remove the four rubber feet from bottom of the unit.
fig.set-02
Note: Do not use these holes.
Installation
When turning the unit
upside-down, get a bunch
of newspapers or
magazines, and place them
under the four corners or at
both ends to prevent
damage to the buttons and
controls. Also, you should
try to orient the unit so no
buttons or controls get
damaged.
2
Attach the RAD-50 adaptor to the AR-200R using the screws
that are supplied with the RAD-50.
fig.set-03
Attaching the Card Protector
By attaching the Card Protector (supplied) to the AR-200R, you can prevent the
memory card from inadvertently being removed from the AR-200R.
1
fig.CardProtect.e
After confirming that the card is securely inserted in the card
slot, use the provided screws to attach the Card Protector, as
shown in the figure below.
RAD-50
When turning the unit
upside-down, handle with
care to avoid dropping it,
or allowing it to fall or tip
over.
Card Protector
11
Examples of Usage and Connection for the AR-200R
You can use the AR-200R alone or in combination with other AR-200R units
or other equipment to play audio in a wide variety of scenes. This section
shows some examples of these. You can use these examples as a starting
point for making changes to match your own usage circumstances.
Together with Other Equipment (System Examples)
Using the Control Input and Output Connectors
• Control Input: Messages, explanations, warnings, announcements, effect
sounds, and the like are played with high sound quality according to
control signals from sensors, buttons, and switches.
fig.use-01
Sensor
Momentary Switch
Pressing the switch plays back
a set announcement, guidance
message, explanation, or the like
•Set announcements played back as required
•Broadcast of museum exhibition explanations
or guidance
Types of External Control
Control Signal
Audio Signal
• Control Output: Control signals can be output during or after phrase
playback to control an external device.
fig.use-02
Busy Out
Program Timer
pm.
Control timer for automatic
broadcasts
•Playback of message broadcasts and
announcements at regular, set times in
offices, factories, or other such areas
•Broadcasts at set times of upcoming
events at amusements areas
Power Amp
“Controlling the AR-200R
from an External Device
(Control Input
Connectors)”
Sensor-triggered automatic
broadcasts
•Guidance announcements made upon
detection of a person's presence
•Playback of event performances at
attractions and other sites
(p. 28)
“Controlling Another
Device with the AR-200R
(Control Output
Connectors)”
Control Signal
Audio Signal
(p. 38)
12
Only during phrase playback, power amp or other
gear is powered up (offset time set to five seconds)
Lamp lights during phrase playback
Power
Control Out
After playback ends, controls external device
* A card created on the AR-3000R/3000/2000 or ARE-3000 is required.
Power Amp
Power Unit
Reray
Switch
Power Amp
•Extinguishing lights
•When elevator doors are closed and
other similar situations
Examples of Usage and Connection for the AR-200R
Using the MIDI Connectors
• Spatial Expression
Using MIDI signals from a master AR-3000R/3000 (sold separately), you
can play back background music performances from sound generating
modules and other devices as well as sound effects phrases on slave AR-
200Rs. This lets you create sonic fields with six-channel multi-playback.
fig.use-03
(As a MIDI Sequencer)
Sound Module
MIDI Patcher
Power Amp
“Controlling the AR-200R
with MIDI Signals (MIDI
Control)”
MIDI Signal
Audio Signal
(p. 42)
Power Amp
Power Amp
• Sound-field Control
Using batch MIDI control from a switch box, you can change programs on a
mixer, equalizer, or the like to control the sonic field.
fig.use-04
Switch Box
Digital Mixer
& Console
MIDI Patcher
Equalizer
( As a MIDI Sequencer)
Power Amp
Control Signal
MIDI Signal
Audio Signal
Equalizer
Power Amp
13
Examples of Usage and Connection for the AR-200R
What You Can Do (Usage Tips)
Repeat Playback of the Same Phrase
There are several methods for doing this. Choose a playback method that
matches your usage conditions.
Changing Playback Mode Settings to Interval Mode
You can have phrases be played back repeatedly at set intervals.
Inputting a Continuous Make-contact Signal to the Control Input
Connectors
You can repeat playback by continuously shorting the control input
connectors.
* With some settings, playback doesn’t repeat even when you continuously input a
make-contact signal.
“Interval Playback”
(p. 34)
For information, refer to
Device (Control Input Connectors)”
“Controlling the AR-200R from an External
(p. 28).
Playing a Variety of Phrases in Succession
There are several methods for doing this. Choose a playback method that
matches your usage conditions.
Using Direct Playback of Control Input
By inputting control signals to a connector number from 1 through 9, you
can play back the phrase assigned to the number.
Using Binary Playback of Control Input
You can select phrases by inputting binary signals to connector numbers 1
through 8, and play the selected phrases in succession each time you input
control signals to the START connector.
“Direct Playback”
“Binary Playback”
(p. 30)
(p. 31)
14
Cards Handled by the AR-200R
b
Types of Usable Cards
The AR-200R stores recorded audio and MIDI signals on the card.
Also, all information other than recorded audio (phrase information) is
stored on the card as well. (That is, it is not stored in the AR unit itself.)
This means that you can change the settings simply by swapping cards.
You can use the ARE-3000 AR Card Editor software to back up all of the data
on memory cards using a Windows computer. When restoring backed up
data to memory cards, be sure to use memory cards formatted with the AR.
Please download the ARE-3000 (free of charge) from the following URL.
http://www.rolandsystemsgroup.net/
Information cannot be
stored in memory in the
AR unit itself, so be sure to
purchase cards separately.
There are several types of
card capacities available.
The amount of information
that you can store differs
according to card capacity.
Depending on the type of
CF card you are using, it
may not be possible to
perform recording or
playback at the set RDAC-
Grade and RDAC-Mode
due to data write speed
and other factors.
Basic Editing Operations
Card Storage Times and Number of Phrases
A maximum of 250 phrases may be created on cards formatted on the AR-
200R.
* The available recording time for a single card varies according to card capacity and
recording settings.
* For a rough guide to maximum recording times with various settings, see the
“Card-specific Audio Recording Time Chart”
53).
in the reference materials (p.
Depending on the length of
stored phrases, it may not
e possible to create the set
maximum number of
phrases.
Formatting a Card
When you use a new card or a card used previously on a device other than
the unit, you must first format (initialize) the card.
* Cards formatted on the AR-3000R/3000 can be used just as they are.
* Please refer to p. 17 for information regarding previous models (AR-2000/100).
The time required for
formatting a card varies
with the card type
(capacity), but may last
from several seconds up to
ten or twenty seconds.
15
Cards Handled by the AR-200R
b
Notes Regarding Formatting
Performing formatting erases all data on the card. Before you format the
card, make sure it contains no data you don’t want to lose.
* Do not format cards on a computer.
* A maximum of 250 phrases may be created on cards formatted on the AR-200R.
* The available recording time for a single card varies according to card capacity and
recording settings.
* For a rough guide to maximum recording times with various settings, see the
“Card-specific Audio Recording Time Chart”
53).
Procedure for Formatting Cards
in the reference materials (p.
Depending on the length of
stored phrases, it may not
e possible to create the set
maximum number of
phrases.
1
2
3
4
5
Confirm that there is no card inserted in the card slot.
Hold down the STOP button for at least 2 seconds
A flashing “Fot” appears.
fig.card-01
Insert the card that you wish to format into card slot.
Never remove a card while
formatting is in progress.
Press the PLAY button, formatting will begin.
If you wish to stop the process, press the STOP button.
When formatting is completed, the message is changed in the display.
fig.card-02
Important Notes on Handling Cards
• When Inserting
Insert the card all the way in—until it is firmly in place.
• When Removing
To remove the card, press the eject button.
Never remove a card during recording, playback, or formatting.
Furthermore, do not turn off the power or remove the AC adaptor cord
during recording, playback, or formatting. Doing so may damage the card.
16
Cards Handled by the AR-200R
Card Compatibility with Other Models in the AR Series
The AR-200R’s file format is the same as the format for the AR-3000R/3000/
200S/200.
Using Cards Formatted on Earlier Model Units with the AR-200R
• Compact Flash cards used with AR-3000R/3000/200S/200s can be used
as is with the AR-200R.
• Files on PC cards used on AR-3000/200/2000/100 models can be used
by copying the data to CompactFlash with the ARE-3000.
In addition, cards can be copied with the AR-3000 using a Compact
Flash Card Adaptor (cards which have not been copied using ARE-3000
or an AR-3000 cannot be used).
Using Cards Formatted on the AR-200R with Earlier Models
• Cards can be used as is with the AR-3000R/3000/200S/200.
• Cards can be used as is with the AR-3000/200 by copying the data to PC
card (PM series) with the ARE-3000. (Use a Compact Flash Card
Adaptor.)
• Cards cannot be used with the AR-2000/100.
(Cards copied using other AR models cannot be used.)
Please download the ARE-3000 (free of charge) from the following URL.
http://www.rolandsystemsgroup.net/
Basic Editing Operations
17
Recording Audio
Recording Units—Phrases
A single item of data recorded from the point where you start recording
until the point where you stop recording is called a phrase. Audio data and
MIDI data are both handled as phrases. Phrases are managed by phrase
numbers.
fig.rec-01
Phrase Number
Connecting External Devices
The AR-200R features analog input jacks (INPUT) on the rear panel.Refer to
the following figure when connecting the AR-200R with external devices.
fig.rec-02
Headphone
Powered Speakers
For monitor
Formatted Card
“What is a MIDI Phrase?”
(P.26)
“Important Notes on
Making Connections and
Switching the Power On
and Off”
(P.9)
CompactFlash™
IN (ANALOG)
AC Adaptor
(PSB-1U)
OUT (ANALOG)
Sound Recording Device
Monitor Output During Recording and Recording Standby
Sounds input from the analog input jack (INPUT) can be output from the
audio output jacks (BALANCED OUTPUT) during recording, recording
standby, and ordinary playback.
* The quality of sounds output from the audio output jack differs from that of RDAC-
Grade or RDAC-Mode sound quality. Be sure to play back the phrase after
recording to confirm the quality of the content.
18
Procedure for Recording
To enable recording with the AR-200R using cards formatted on the AR-
2000, carry out the
Required Settings for Recording Audio Signals (Recording Settings)
In order perform recording matched to usage conditions, including the
connected equipment, recording source, sound quality, time, and playback
system, you make recording settings.
Recording settings are made in phrase units. You can mix phrases having
different recording settings on a single card.
The possible recording time of a card varies according to the recording
settings. For a rough guide to maximum recording times with various
settings, see the
“Formatting a Card”
“Recording Audio”
(P.15) procedure.
(P.18) in the reference materials (p. 53).
Recording Audio
Basic Editing Operations
RDAC-Grade (
The RDAC grade is the type of sampling frequency for digital recording.
On the AR-200R, you can select from among six grades.
fig.rec-03
S-HIGH :
HIGH :
STANDARD :
LONG1 :
LONG2 :
ANNOUNCE :
STANDARD is best for ordinary recording. ANNOUNCE uses up the least
card space, and is best for recording announcements, narration, and the like.
When you are recording audio such as a narration with ANNOUNCE or
LONG2, you can record with higher clarity by using the equalizer to cut the
bass range. Select an RDAC grade that matches the circumstances of use.
sampling frequency) (REC MODE SW–3)
Amount of card
memory consumed
Large
Small
48 kHz
44.1 kHz
32 kHz
22.05 kHz
16 kHz
8 kHz
Sound
quality
High
1
2
Procedure
Turn off the power of the AR-200R.
Set the SW 1-3 REC MODE switches on the AR-200R’s bottom
panel.
19
Recording Audio
The different grade settings are shown in the following table.
SW 1 SW 2 SW 3
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
3
RDAC-Grade
ANNOUNCE
LONG2
LONG1
STANDARD
HIGH
S-HIGH
Turn on the power of the AR-200R.
* Use a narrow-tipped object to set the MODE switches to ON or OFF.
RDAC-Mode (Signal Processing Format)
The RDAC mode is a type of digital data processing system for recording.
On the AR-200R, you can select from among four modes.
fig.rec-04
LINEAR :
MODE3 :
MODE2 :
MODE1 :
16 bit PCM Recording
About 2.5 times the recording time of Linear.
More than 2.5 times the recording time
of Linear.
About 4 times the recording time of Linear.
OFF
OFF
OFF
OFF
ON
ON
(REC MODE SW 4, 5)
Sound
quality
High
Amount of card
memory consumed
Large
Small
If the type of card does not
provide the recording time you
want, change the RDAC mode
or RDAC grade setting to use
less card capacity, then
perform recording again.
“Card-specific Audio
Recording Time Chart”
(P.53)
1
2
3
LINEAR enables recording at the highest sound quality, but uses the most space
on the card. MODE1 uses up the least card space, and is suited to long recording
times. Select an RDAC mode that matches the circumstances of use.
Procedure
Turn off the power of the AR-200R.
Set the SW 4 and 5 REC MODE switches on the AR-200R’s
bottom panel.
The different grade settings are shown in the following table.
RDAC-Mode
MODE 1
MODE 2
MODE 3
LINEAR
SW 5SW 4
OFF
ON
OFF
ON
OFF
OFF
ON
ON
Turn on the power of the AR-200R.
20
* Use a narrow-tipped object to set the MODE switches to ON or OFF.
What’s RDAC?
RDAC (Roland Digital Audio Coding) is a proprietary audio recording
standard from Roland.
It achieves high sound quality and also makes it possible to record for long times.
If You’re Not Sure About Which Grade and Mode to Choose
Recording Audio
The optimal grade and mode vary according to the usage conditions,
including the connected equipment, recording source, sound quality, time,
and playback system.
The factory default settings are RDAC-Grade: LONG1; and RDAC-Mode: MODE1.
First, try recording and playback with these settings. In most cases, this
yields satisfactory sound quality.
Recording Type (Stereo/Mono)
Select either stereo recording or mono recording.
Choosing mono recording gives you recording times that are twice as long
as with stereo recording.
Procedure
1.
Turn off the power of the AR-200R.
2.
Set the SW 6 REC MODE switch on the AR-200R’s bottom panel.
OFF: MONO
ON: STEREO
3.
Turn on the power of the AR-200R.
Basic Editing Operations
(REC MODE SW 6)
* Use a narrow-tipped object to set the MODE switches to ON or OFF.
What is mono recording
In the case of mono recording, input the audio signal to the “MONO/L”
input jack. When audio signals are input simultaneously to the “MONO/L”
and “R” input jacks, L and R are mixed and recorded.
Line Thru Output
REC SW6: OFF (mono)
When audio signals are input to “MONO/L,” output is from OUTPUT L
and R. When audio signals are input to “R,” output is from OUTPUT R only.
When audio signals are input to both “MONO/L” and “R,” solely the
signals input to “MONO/L” are output from OUTPUT L, while the
“MONO/L” and “R” signals are mixed and output from OUTPUT R.
REC SW6: ON (stereo)
Audio signals input to “MONO/L” are output from OUTPUT L, and audio
signals input to “R” are output from OUTPUT R.
21
Recording Audio
Procedure
Make the correct connections, then turn on the power switch.
1
Insert a formatted card into one of the slots.
“Important Notes on
Making Connections and
Switching the Power On
and Off”
(P.9)
2
3
4
Press the [ ] or [ ] button to select the number of the phrase
to be recorded.
The non-recording phrase number in display is flashed.
fig.rec-05
* If you are re-recording over a previously recorded phrase, you should delete the
phrase. (p. 25)
* You cannot change the phrase number after recording, so be sure to select the phrase
number you want to record.
Hold down the STOP button and press the PLAY button to go
into recording standby.
The PLAY indicator is flashed while the recording standby mode.
Input the sounds from the device connected to the input jacks,
then use the input volume knob to adjust the recording level
so that the MIDI/CLIP indicator does not light.
Nominal Input level:0 dBm
Maximum input level: +2 dBu
* If signals louder than +2 dBu are being input, rotate the input volume knob to the
left of center.
* Press the STOP button and recording standby mode will end.
22
Loading...