Roland Corporation TD-10 Owner's Manual
®
We’d like to take a moment to thank you for purchasing the Roland Percussion
Sound Module TD-10.
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY
INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (p. 3, 4), and “IMPORTANT
NOTES” (p. 17). These sections provide important information concerning the
proper operation of the unit. Additionally, in order to feel assured that you have
gained a good grasp of every feature provided by your new unit, this manual should
be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
Copyright © 1997 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
Read all the instructions before using the product.
Do not use this product near water — for example, near a
bathtub, washbowl, kitchen sink, in a wet basement, or near
a swimming pool, or the like.
This product should be used only with a cart or stand that is
recommended by the manufacturer.
This product, either alone or in combination with an amplifier
and headphones or speakers, may be capable of producing
sound levels that could cause permanent hearing loss. Do
not operate for a long period of time at a high volume level
or at a level that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should consult an
audiologist.
The product should be located so that its location or position
does not interfere with its proper ventilation.
The product should be located away from heat sources such
as radiators, heat registers, or other products that produce
heat.
The product should be connected to a power supply only of
the type described in the operating instructions or as marked
on the product.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
A.
B.
C.
D.
E.
The power-supply cord of the product should be unplugged
from the outlet when left unused for a long period of time.
Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
The product should be serviced by qualified service
personnel when:
The power-supply cord or the plug has been damaged; or
Objects have fallen, or liquid has been spilled into the
product; or
The product has been exposed to rain; or
The product does not appear to operate normally or
exhibits a marked change in performance; or
The product has been dropped, or the enclosure
damaged.
Do not attempt to service the product beyond that described
in the user-maintenance instructions. All other servicing
should be referred to qualified service personnel.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product — if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
For the USA
The product which is equipped with a THREE WIRE GROUNDING TYPE LINE PLUG must be grounded.
WARNING:
IMPORTANT:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
THIS APPARATUS MUST BE EARTHED
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
For the U.K.
2
•Before using this unit, make sure to read the instructions below, and the Owner’s Manual.
...........................................................................................................
•Do not open or perform any internal modifications
on the unit. (The only exception would be where
this manual provides specific instructions which
should be followed in order to put in place userinstallable options; see p. 43.)
...........................................................................................................
•When using the unit with a rack or stand recommended by Roland, the rack or stand must be carefully placed so it is level and sure to remain stable. If
not using a rack or stand, you still need to make
sure that any location you choose for placing the
unit provides a level surface that will properly support the unit, and keep it from wobbling.
...........................................................................................................
•Use only the attached power-supply cord.
...........................................................................................................
• Avoid damaging the power cord. Do not bend it
excessively, step on it, place heavy objects on it, etc.
A damaged cord can easily become a shock or fire
hazard. Never use a power cord after it has been
damaged.
...........................................................................................................
•In households with small children, an adult should
provide supervision until the child is capable of following all the rules essential for the safe operation
of the unit.
...........................................................................................................
• Protect the unit from strong impact.
(Do not drop it!)
...........................................................................................................
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using extension
cords—the total power used by all devices you have
connected to the extension cord’s outlet must never
exceed the power rating (watts/amperes) for the
extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt
through.
...........................................................................................................
• Before using the unit in a foreign country, consult
with your dealer, or qualified Roland service personnel.
...........................................................................................................
•Always turn the unit off and unplug the power cord
before attempting installation of the circuit board
(WAVE & SYSTEM EXPANSION BOARD TDW series; p.
43).
...........................................................................................................
• Do not put anything that contains water (e.g., flower
vases) on this unit. Also, avoid the use of insecticides, perfumes, alcohol, nail polish, spray cans, etc.,
near the unit. Swiftly wipe away any liquid that
spills on the unit using a dry, soft cloth.
...........................................................................................................
USING THE UNIT SAFELY
3
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an
outlet or this unit.
...........................................................................................................
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
...........................................................................................................
• Never climb on top of, nor place heavy objects on
the unit.
...........................................................................................................
• Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from, an
outlet or this unit.
...........................................................................................................
• Before moving the unit, disconnect the power plug
from the outlet, and pull out all cords from external
devices.
...........................................................................................................
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (p. 27).
...........................................................................................................
• Whenever you suspect the possibility of lightning in
your area, pull the plug on the power cord out of
the outlet.
...........................................................................................................
• Install only the specified circuit board(s) (WAVE &
SYSTEM EXPANSION BOARD TDW series).
Remove only the specified screws (p. 43).
...........................................................................................................
USING THE UNIT SAFELY
4
This owner’s manual is organized as follows.
Quick Start
This section is intended for those using the TD-10 for the first time, and explains how to use various
functions in a simple way. Please read Quick Start and follow along by actually operating the TD-
10. This will help you understand most of what you need to know for basic operations. If you find
unfamiliar words or terms, refer to the “Glossary” on p. 169. More advanced ways of using the TD10, or details of other operations are explained the Reference section.
Advanced Use
This section explains all functions of the TD-10 in detail and is divided into specific parts. Basic
panel operations and displays are covered in the Quick Start. The Advanced Use section assumes
you already understand basic procedures, so if anything’s unclear, refer to the “Quick Start.”
Chapter 1. Overview of the TD-10 V-drums
This chapter explains the concept of the TD-10 and how it is organized. Read this chapter in order to
understand what the TD-10 is.
Chapters 2–5. Functions for creating sound
If you wish to learn more about the sound creation possibilities introduced in the “Quick Start,”
refer to chapters 2–5.
Chapter 6. Using a sequencer and related functions
This chapter explains sequencer functions such as performance, recording, click settings, and pattern
editing.
Chapter 7. Settings for the entire TD-10
This chapter explains settings that affect the entire TD-10, such as adjusting the overall sound, saving data to a memory card etc.
Chapters 8 and 9. Convenient functions and how to use them
These chapters explain how to use pads or pedals for pattern play back, and other functions, and
about time-saving operations such as copy and help.
Chapter 10. Functions using MIDI
This chapter explains how to use MIDI—whether it be for saving data to an external device, or for
using the TD-10 as a sound module.
Appendices
If you run into problems, refer to “Troubleshooting” to make sure that the settings are correct. If an
error message appears during operation, refer to “Message/Error Message List” and take appropriate action. This section also provides information related to sound editing, MIDI, various lists, and
the MIDI implementation charts.
* The display screens printed in this owner’s manual are based on the factory settings. However, please be aware
that in some cases they may differ from the actual factory settings.
How to read this owner’s manual
5
IMPORTANT SAFETY INSTRUCTIONS............................................................................2
USING THE UNIT SAFELY.................................................................................................3
How to read this owner’s manual........................................................................................5
Features............................................................................................................................12
Front and rear panel..........................................................................................................14
Important notes .................................................................................................................17
About button operations and the screen displays .............................................................18
Quick Start ..............................21
Before you begin playing..........................22
Mounting the TD-10 to the stand.......................................................................................22
Connect your audio system or amp...................................................................................23
Connecting pads and pedals.............................................................................................24
Turning on the power ........................................................................................................26
To turn the power off ........................................................................................................................27
Listening to the internal demo playback............................................................................28
Specify the pads that the TD-10 will use...........................................................................29
If you have purchased the “V-Basic Kit” or “V-Standard Kit”....................................................29
If you have purchased the PD-5, PD-7, PD-9, PD-100 or PD-120 individually .........................30
Using triggers on an acoustic drum to play the TD-10 .................................................................33
Check the settings.............................................................................................................34
For a better performance ..........................35
Concerning the performance & expressiveness of the pads.............................................35
Rim shots..............................................................................................................................................35
Choking................................................................................................................................................35
Positional sensing ...............................................................................................................................36
Playing with brushes..........................................................................................................................36
Hi-hat control pedal ...........................................................................................................................36
TD-10 operating procedure...............................................................................................37
Adjusting the volume.........................................................................................................................37
Selecting a drum kit............................................................................................................................38
Adjusting the sensitivity of a pad.....................................................................................................39
Master equalizer..................................................................................................................................40
Effect on/off ........................................................................................................................................41
Help function.......................................................................................................................................42
About expansion boards....................................................................................................43
À propos des cartes d’extension.......................................................................................44
(French language for Canadian Safety Standard)
Troubleshooting connections and settings........................................................................45
Features of the preset drum kits................47
How sounds are created on the V-drums..........................................................................47
No.36: 70’s Rock drum kit.................................................................................................48
No.37: Brush Kit................................................................................................................50
No.38: Electronic drum kit.................................................................................................52
Contents
6
Modifying a drum kit................................54
[INST]: Creating drum sounds ..........................................................................................55
Selecting an instrument......................................................................................................................55
Modify the material and depth of the body....................................................................................56
Change the material and tuning of the head..................................................................................58
Adjust the muffling (muting) and snare strainer tension.............................................................60
[STUDIO]: Adjusting the acoustics of the room.................................................................62
Decide “where” the drums are played............................................................................................63
Change the size of the room..............................................................................................................64
[CONTROL ROOM]: Adding finishing touches to the sound.............................................65
Using the equalizer to modify the sound........................................................................................65
Adjusting the volume balance of the instruments.........................................................................67
Examples and convenient tips...................68
Perform with the on-board sequencer...............................................................................68
Playing back a preset pattern............................................................................................................68
Play the pads along with a preset pattern.......................................................................................69
Drum Kit Chain—Selecting drum kits in the desired order................................................70
Using a foot switch to select kits .......................................................................................72
Using a pad to playback patterns......................................................................................72
Using headphones to hear the click sound .......................................................................73
Using the TD-10 as a MIDI sound module........................................................................74
Advanced Use .........................75
Chapter 1. Overview of the TD-10 V-drums.......76
How the V-drums system is organized..............................................................................76
How to select pads............................................................................................................77
Using pads to select the pad/sound for editing ............................................................................77
Using the TD-10 to select the pad/sound for editing....................................................................77
Chapter 2. Settings for the entire drum kit ....78
Selecting a kit....................................................................................................................78
Selecting kits from the list display .....................................................................................78
Naming a kit ......................................................................................................................78
Making settings for brush performance.............................................................................79
Effect switches for the entire kit.........................................................................................79
Contents
7
Chapter 3. Instrument settings ..................80
Selecting an instrument.....................................................................................................80
Selecting instruments from the list display........................................................................80
Editing an acoustic drum kit (V-EDIT) ..............................................................................81
Selecting the shell material................................................................................................................81
Changing the shell depth...................................................................................................................82
Selecting the head material................................................................................................................82
Tuning the head..................................................................................................................................82
Muffling settings (muting) ................................................................................................................83
Adjusting the snare strainer tension................................................................................................83
Editing an electronic drum kit (V-EDIT).............................................................................84
Editing a TR-808/909 (V-EDIT).........................................................................................85
Editing hi-hat, cymbals and percussion.............................................................................86
Chapter 4. Studio settings .........................87
Settings for the entire drum kit ..........................................................................................87
Selecting the studio/room.................................................................................................................87
Changing the size of the room..........................................................................................................87
Changing the wall material...............................................................................................................87
Selecting the ambience mike location..............................................................................................87
Adjusting the volume and output assignments of the ambience................................................88
Settings for each instrument..............................................................................................88
Adjusting the amount of ambience..................................................................................................88
Selecting the type of mike and its location......................................................................................88
Settings for each group.....................................................................................................89
Adjusting the amount of ambience send level for each group ....................................................89
Chapter 5. Control room settings...............90
Settings for each instrument..............................................................................................90
Adjusting volume (level)...................................................................................................................90
Adjusting pan (stereo location).........................................................................................................90
Adjusting effect send level ................................................................................................................90
Selecting output assignments............................................................................................................91
Controlling variations in volume (Compressor)............................................................................91
Customizing the tone (Equalizer).....................................................................................................92
Settings for the entire drum kit ..........................................................................................93
Adjusting effect Return level ............................................................................................................93
Selecting the type of effect.................................................................................................................93
Editing the effects ...............................................................................................................................94
Settings for an entire group...............................................................................................96
Adjusting effect send level for an entire group..............................................................................96
Adjusting the volume by group .......................................................................................................96
Contents
8
Chapter 6. Sequencer................................97
Basic sequencer operation................................................................................................97
Using Preset Patterns .........................................................................................................................97
Setting the tempo..............................................................................................................97
Setting the tempo for each pattern...................................................................................................97
Temporarily changing the tempo of the currently-playing pattern............................................97
Playback functions ............................................................................................................98
Selecting a pattern...............................................................................................................................98
Selecting patterns from the list .........................................................................................................98
Selecting how a pattern will playback.............................................................................................98
Click settings.....................................................................................................................99
Click on/off and volume settings ....................................................................................................99
Setting the tempo................................................................................................................................99
Setting the time signature and click interval ..................................................................................99
Selecting the click sound..................................................................................................................100
Using ambience.................................................................................................................................100
Using effects ......................................................................................................................................100
Adjusting the pan (stereo location)................................................................................................100
Selecting the output destination.....................................................................................................100
Recording........................................................................................................................101
Basic recording procedure...............................................................................................................101
The Rehearsal function ....................................................................................................................102
Using a count-in................................................................................................................................102
Start recording the moment that you strike a pad.......................................................................102
Correcting timing as you record (Quantize).................................................................................103
Importing data from another sequencer into the TD-10.............................................................103
Editing a pattern..............................................................................................................103
Naming a pattern..............................................................................................................................103
Erasing a pattern...............................................................................................................................104
Erasing selected measures of a pattern..........................................................................................104
Copying a pattern.............................................................................................................................104
Copying selected measures of a pattern........................................................................................105
Clearing a pattern .............................................................................................................................105
Clearing selected measures of a pattern........................................................................................105
Connecting two patterns..................................................................................................................106
Settings for part instruments ...........................................................................................106
Adjusting the master tuning ...........................................................................................................106
Instrument selection and settings for each part ...........................................................................106
Mixer settings for each part.............................................................................................................107
Muting a specific part.......................................................................................................................107
Contents
9
Chapter 7. Settings for the entire TD-10...108
Changing output assignment for audio received by the MIX IN jack...............................108
Specifying the type of pad...............................................................................................108
Basic settings for the trigger parameters (BASIC) ..........................................................109
Detailed settings for the trigger parameters (ADVNCD)..................................................111
The order in which trigger parameters should be set when using drum triggers.............112
Adjusting the brightness of the display............................................................................113
Setting the master equalizer............................................................................................113
Saving data to a memory card ........................................................................................114
Loading data from a memory card ..................................................................................115
Automatically switching the display (Note Chase)...........................................................115
Chapter 8. Convenient functions..............116
Selecting kits in the desired order (Drum Kit Chain) .......................................................116
Specifying a Drum Kit Chain..........................................................................................................116
Naming a Drum Kit Chain..............................................................................................................116
Copying...........................................................................................................................117
The UNDO function.........................................................................................................117
Getting help.....................................................................................................................118
Specifying how the Preview button functions..................................................................118
Chapter 9. Operations using pads and
foot switches ..........................................119
Using pads to play patterns (Pad Pattern) ......................................................................119
Using pads to perform button operations (Pad Switch) ..................................................119
Using foot switches to perform button operations (Foot Switch).....................................120
Chapter 10. Functions using MIDI ............121
Saving/Loading data to/from an external device (Bulk Dump)........................................121
Saving data ........................................................................................................................................121
Loading saved data to the TD-10....................................................................................................121
Setting the Device ID—Transmitting saved data to two or more TD-10 units........................122
Using pads to play an external MIDI sound module........................................................122
Selecting the note number transmitted by each pad ...................................................................122
Setting the Gate Time.......................................................................................................................123
Setting the MIDI channel.................................................................................................................123
Using the TD-10 with the Roland SPD-11.......................................................................123
MIDI settings for the entire TD-10...................................................................................124
Setting the MIDI channels for each Part........................................................................................124
Turning off Local Control................................................................................................................124
Disabling reception or transmission of Program Changes.........................................................124
Reducing the amount of data transmitted by the FD-7 (Pedal Data Thin) ..............................124
Using the TD-10 as a sound module...............................................................................125
Setting the instrument for each part ..............................................................................................125
Adjusting the mixer settings for each part....................................................................................125
Regarding note numbers for the drum kit sounds ......................................................................125
Using the percussion group ............................................................................................................126
Changing the kit number that is selected by a program change...............................................128
Contents
10
MIDI messages for detailed performance expressions...................................................128
Messages for hi-hat control .............................................................................................................128
Messages for positional sensing (snare drum and ride cymbal only).......................................129
Synchronization with external MIDI devices....................................................................129
Appendices............................131
Troubleshooting...............................................................................................................132
Instruments that can be used with each trigger...............................................................136
Restoring the factory settings (INITIALIZE).....................................................................137
Message / error message list..........................................................................................138
About MIDI ......................................................................................................................140
Using drum triggers.........................................................................................................142
Preset list.........................................................................................................................143
MIDI implementation .......................................................................................................154
MIDI implementation chart ..............................................................................................165
Specifications..................................................................................................................168
Glossary..........................................................................................................................169
Index of screen displays..................................................................................................173
Index................................................................................................................................176
* PinStripe is a registered trademark of Remo Inc. U.S.A.
Contents
11
●Enhanced tonal quality and expressiveness that rivals acoustic
drums
The TD-10 features a newly developed modeling sound module that relies on COSM technology.
The force and position of the hit are detected, providing sensitive and dynamic expression that is
extremely close to that of acoustic drums. In addition, when PD-100 or PD-120 (optional) pads are
used, you can enjoy excellent response when playing rolls.
* COSM (Composite Object Sound Modeling) is a Roland technology which combines multiple sound model-
ing processes to create new sounds.
* Positional detection is possible on snare drums and ride cymbals.
●With 600 drum sounds and 54 backing instrument provided
A rich array of instrumental sounds are provided, sufficient to cover all styles of music.
●A user interface comfortable for drummers
You can create sounds much in the same way that you would using acoustic drums when you select
a preferred drum head, tune it, and attach muffling (muting) material. With the large display, the
use of graphics and icons to portray parameters being set and their meanings, operation is intuitive
and easily understood.
●High-speed trigger response
The triggering time (time delay from hitting the pad until you hear the sound) is faster than ever,
allowing expressiveness and dynamics to be reproduced accurately.
●Twelve pads can be used simultaneously
Since up to twelve pads can be used simultaneously, you can create large-scale setups bigger than
ever before. This also gives you flexibility for extended applications, such as using pads as switches
(Pad Switch) or for pattern playback (Pad Pattern).
●Simulate the entire process of actual recording
By being able to choose drum materials, sizes, studio location, mike types and their settings, effects
and mixer parameters, the TD-10 allows total flexibility for recording or live applications. All of
these settings can be stored as part of a drum kit,for instant recall at any time.
●Perform using brushes
If you use the PD-100 or PD-120 pads, you can play with brushes, something not possible with any
previous electronic drum system. (Nylon brush only please!).
●Sound processing specially selected for drums
For each instrument assigned to trigger inputs 1–10, individual two-band equalizers and compressors are provided. In addition,(in the control room) —there are digital effects: reverbs, flanger, chorus, delays, pitch shift delay, and phaser. A three-band equalizer is also provided for processing the
sound at the MASTER OUT. Ambience(in the Studio) lets you choose WHERE the drums are being
played. You can change the sound of that space by changing the material of the walls, size of the
room and the position of the ambient mikes. There are individual ambience send levels for all
instruments.
Features
12
●Functions and operations perfect for live performances
The group faders on the front panel let you make quick changes as needed during performance. You
can play drum kits in any desired order (Drum Kit Chain). The INC/DEC buttons are large enough
to be pressed with a drum stick. (Don’t HIT them!) Another very useful function allows you to send
the click sound ONLY to the headphones if desired. An audio input (stereo) for custom monitoring
(MIX IN jack) is also provided.
●Easy-operation sequencer is built-in
With easy, tape recorder-like operations, you can record or play back patterns. In addition to the
drums, three backing parts can be added for ensemble practice or for creating backing patterns via
MIDI keyboard, external sequencer etc.
* Brush swish/sweeping and choke cannot be recorded.
●Previous models of pads can be used
Previous pad models (PD-5, PD-7, PD-9), kick trigger units (KD-5, KD-7) and the hi-hat control
pedal (FD-7) are all compatible. Also, the PD-7 and PD-9 allow positional sensing for the snare drum
and ride cymbal.
●User Installable Expansion boards allow extended functionality
WAVE & SYSTEM EXPANSION BOARD TDW series will bring more instruments and drum kits to
the TD-10, and allows the system to be upgraded through Flash ROM. A memory card (M-512E) can
be used to store all kits and patterns for the TD-10.
●Usable as a MIDI sound module
Percussion groups are provided so these sounds can be accessed via MIDI as with a dedicated module, so in addition to sounds assigned to the 12 trigger inputs, a special note map for percussion
allows 72 types of instruments to be accessed simultaneously.
Features
13
Front Panel
1
2
3
4
5678
9
10
11 12 13 14
15 16 17
18
20
19
21
22
Front and rear panel
14
Trigger Indicator
This will light when a trigger signal (signal produced when
pad is struck) is received from a pad. It allows you to check
whether the pad has been connected correctly.
LED Display
Displays the number of the currently selected drum kit.
Graphic Display
During performance, this indicates the drum kit name and
other important information. During editing, various graphics and text relative to the editing process is indicated.
* In this owner’s manual, this will be referred to simply as
“the display.”
F1-F4 Buttons
These buttons change their function depending on the contents of the display. The lower part of the display will indicate the function of each button (p. 18).
EXIT Button
Press this button and you will return to the screen one level
higher in the hierarchy. Repeated pressing takes you back to
the “DRUM KIT” page.
TOOLS Button
Provides access to functions such as Copy, Undo, and Help.
(p. 42, 117)
CHAIN Button
Lets you make Drum Kit Chain settings (a function that
arranges drum kits in a desired order for successive selection) (p. 70, 116).
SETUP Button
Here you can make settings that affect the entire TD-10, such
as trigger parameters and MIDI settings (p. 108).
1
2
3
4
5
6
7
8
GROUP FADERS
These allow you to adjust the volume of the kick, snare, hihat, other percussion instruments, backing instruments, and
the click sound (p. 37).
SEQUENCER
Here are the buttons that control sequencer functions (playback/recording of performance patterns) (p. 68, 97).
KIT Button
Provides access to the basic display page used when playing
the TD-10.
INST (Instrument) Button
Provides access to the display page in which you can edit
instruments (p. 55, 80).
STUDIO Button
Provides access to the display page where you can choose
mike types, their positions, ambience types and ambient
mike positions (p. 62, 87).
CONTROL ROOM Button
Allows you to edit mixer, EQ, compressor and effect parameters (p. 65, 90).
MIX IN Knob
This adjusts the volume of the device connected to the MIX
IN jack. The sound from the MIX IN will be output from the
MASTER out and/or the PHONES jack.
PHONES Knob
Adjusts the headphone volume. Even when headphones are
connected, sound will still be output from the various output jacks.
MASTER Knob
Adjusts the volume of the MASTER OUT jacks. The volume
of the PHONES jack is adjusted by the PHONES knob.
CURSOR Buttons
Used to move the cursor in the display, or to access the next
display page (p. 18).
VALUE Dial
This dial has the same function as the INC and DEC buttons.
Use this dial when you wish to make large changes in drum
kit settings or edited values (p. 19).
TRIG SELECT
Use the lower two buttons to select the pad (trigger number)
for which you wish to make settings. To select the rim of a
pad, press the RIM button, then the RIM indicator is lit. If
pads are connected to the TD-10, you can also select a pad
by striking it. The PREVIEW button lets you audition the
instrument that is assigned to the selected pad or the sound
appearing in the display when editing a percussion group
(p. 20).
PREVIEW Button
Used to audition an instrument. By using TRIG SELECT buttons to select a pad, you can play and edit sound even if no
pads are connected to the TD-10. The button is velocity sensitive (p. 20).
INC Button, DEC Button
These buttons are used to switch drum kits or to modify values. Pressing the INC button increases the value, and pressing the DEC button decreases it. Since these buttons are
large, you can also use the tip of your drum stick to press
them (p. 19).
* Please be aware that hitting the buttons with a stick can
cause malfunctions.
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Front and rear panel
15
Rear Panel
23
24
2529
30
3132
33
34
26
2728
Front and rear panel
16
MEMORY CARD Slot
An M-512E memory card (optional) can be inserted into this
slot. Each memory card can store all settings of the TD-10,
such as drum kits and sequencer performance data, etc (p.
114).
* The M-512E is the only memory card that can be used by
the TD-10.
TRIGGER INPUT Jacks
Accept the pads or kick trigger units you want to connect to
the TD-10. To connect a dual trigger type pad (PD-7, PD-9,
PD-120), use a stereo cable (p. 24).
FOOT SWITCH Jack
Accepts connection of an optional foot switch (FS-5U). A
foot switch can be used to select kits and start/stop the
sequencer, etc. Use a special PCS-31 cable (optional) (p. 72,
120).
HH CTRL Jack
Accepts connection of a hi-hat control pedal (FD-7) (p. 36).
OUTPUT (MASTER) Jacks
These jacks output the instrumental sounds of the TD-10,
and are for connection to external audio devices or amps. If
you are listening in mono, connect to only the MASTER L
(MONO) jack (p. 23).
OUTPUT (DIRECT 1, 2, 3) Jacks
The direct outs allow you to have more “separation,” over
the total kit, and can be used for external effects etc.
Ambience may also be sent from these outputs, but NOT the
digital effects. Output assignments DIRECT 1, 2 or 3 jacks
are found in the Control Room (p. 91).
PHONES Jack
A pair of stereo headphones can be connected to this jack.
Even if headphones are connected, sound will still be output
from the OUTPUT jacks (p. 23).
MIX IN Jack
This jack is used to connect a CD or cassette player, or as a
custom monitoring input for live/recording performances.
The sound that is input to this jack will be output from the
MASTER out jacks and/or the PHONES jack (p. 108).
MIDI IN Connector
Use this connector when you wish to use an external MIDI
sequencer to play the sounds of the TD-10, or when loading
TD-10 settings (bulk data) that were saved on an external
device (p. 121).
MIDI OUT/THRU Connector
Use this connector when you wish to use play sounds in an
external MIDI sound module/sampler from the pads, or
when you wish to transmit TD-10 settings (bulk data) to
another MIDI device (p. 121).
POWER Switch
This switch turns the power on/off (p. 26).
AC Inlet
Connect the included AC power cable to this inlet (p. 23).
23
24
25
26
27
28
29
30
31
32
33
34
Power Supply
● Do not use this unit on the same power circuit with any
device that will generate line noise (such as an electric
motor or variable lighting system).
● Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Placement
● Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit;
or move it farther away from the source of interference.
● This device may interfere with radio and television recep-
tion. Do not use this device in the vicinity of such
receivers.
● Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes.
Excessive heat can deform or discolor the unit.
Maintenance
● For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
● Never use benzene, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
Repairs and Data
● Please be aware that all data contained in the unit’s mem-
ory may be lost when the unit is sent for repairs.
Important data should always be backed up on a RAM
card/DATA card, in another MIDI device (e.g., a
sequencer), or written down on paper (when possible).
During repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related
to memory itself is out of order), we regret that it may not
be possible to restore the data, and Roland assumes no
liability concerning such loss of data.
Memory Backup
● This unit contains a battery which powers the unit’s
memory circuits while the main power is off. When this
battery becomes weak, the message shown below will
appear in the display. Once you see this message, have
the battery replaced with a fresh one as soon as possible
to avoid the loss of all data in memory. To have the battery replaced, consult with your dealer, or qualified
Roland service personnel.
“Backup Battery Low !”
Additional Precautions
● Please be aware that the contents of memory can be irre-
trievably lost as a result of a malfunction, or the improper
operation of the unit. To protect yourself against the risk
of loosing important data, we recommend that you periodically save a backup copy of important data you have
stored in the unit’s memory on a RAM card/DATA card,
in another MIDI device (e.g., a sequencer).
● Unfortunately, it may be impossible to restore the con-
tents of data that was stored on a RAM card/DATA card,
in another MIDI device (e.g., a sequencer), in the unit’s
memory once it has been lost. Roland Corporation
assumes no liability concerning such loss of data.
● Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
● Never strike or apply strong pressure to the display.
● When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s internal elements.
● A small amount of heat will radiate from the unit during
normal operation.
● To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those
around you (especially when it is late at night).
● Since sound vibrations can be transmitted through floors
and walls to a greater degree than expected, take care not
to allow such sound to become a nuisance to neighbors,
especially at night and when using headphones.
Although the drum pads and pedals are designed so
there is a minimal amount of extraneous sound produced
when they're struck, rubber heads tend to produce louder
sounds compared to mesh heads. You can effectively
reduce much of the unwanted sound from the pads by
switching to mesh heads.
● When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
● Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the following precautions.
❍ Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
Before Using Cards
Using DATA Cards
● New M-512E DATA cards do not yet have their battery
installed. Before a DATA card can be used, you first need
to insert the battery (refer to the instructions supplied
with the DATA card).
● M-512E DATA cards are equipped with a PROTECT
switch, which when turned on protects your data from
accidental erasure. It is recommended that the switch be
kept at the ON position, and switched to OFF only at the
times you wish to write new data onto the card.
● When the battery in an M-512E DATA card is nearly
worn out, the message below will be shown in the display. Refer to the instructions supplied with the DATA
card and promptly replace the battery to avoid the loss of
the data on it.
“MEMORY CARD Battery Low ! Please Change !”
● Carefully insert the DATA card all the way in—until it is
firmly in place.
● Never touch the terminals of the DATA card. Also, avoid
getting the terminals dirty.
OffOn
Important notes
17
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and
“USING THE UNIT SAFELY” on pages 2–4, please read and observe the following:
Operations common to all aspects of operating the TD-10 are covered below.
■ Saving your settings
For operations within the TD-10, there is no procedure for “saving settings.” When you modify the
value of a setting, the new value is automatically saved as soon as you make the change.
■ Buttons, sliders and knobs
Buttons, sliders and knobs on the front panel will be printed in square brackets [ ]; e.g., [SETUP].
■ Cursor
fig.00-003e
Cursor refers to the highlighted characters indicating an on-screen item that can be set. If the screen
contains more than one item that can be set, use the [CURSOR] buttons to move it to the item that
you wish to set.
fig.00-003a
■ Function buttons ([F1]–[F4])
fig.00-004
The [F1]–[F4] buttons are called the “function buttons.” The bottom part of the display will show the
names of the functions available for [F1]–[F4]. For example, if this owner’s manual makes reference
to [INST]-[F1 (SHELL)], press [INST] , and then press [F1] (in this case, “SHELL” is displayed above
[F1]).
Cursor
About button operations and the screen displays
18
■ How to modify settings
fig.00-005e
[INC] and [DEC] (referred to in this manual as [INC/DEC]) and the VALUE dial are both used to
modify the values of settings. The two methods have the following advantages.
[INC/DEC]
• Each time [INC] is pressed, the value increases. Each time [DEC] is pressed, the value decreases.
This is convenient for fine adjustments.
• When making an on/off setting, [INC] will turn the setting on and [DEC] will turn it off.
• If you hold down [INC] and press [DEC], the value will increase rapidly. If you hold down [DEC]
and press [INC] the value will decrease rapidly.
VALUE dial
Since the dial allows you to make major changes to the value at once, it’s a convenient way to make
broad adjustments to a parameter quickly.
■ About the upper right of the screen display
fig.00-006e
In pages that allow you to make settings for each pad, you can strike the desired pad to see the setting page for that pad. At this time, the upper right of the display will show the number of the trigger jack to which the selected pad is connected, the instrument that it is using, and the MIDI note
number. The first character (“H” or “R”) indicates whether the head or the rim of the pad is selected.
The numerals at the right are the MIDI note number. You will need to know the MIDI note number
when using the TD-10 as a MIDI sound module.
The “H” or “R” display will indicate whether the head or rim will sound when you press the
Preview button. In cases where settings for the head and rim can be edited separately, the following
characters will also be displayed, letting you know the page in which you are.
fig.00-007
INC/DEC button VALUE dial
Trigger number
Instrument name (or Trigger name)
Rim
Head
MIDI note number
About button operations and the screen displays
19
■ Selecting pads from the TD-10 front panel
fig.00-008
The trigger select buttons ([TRIG SELECT]) are used when you wish to select a sound for editing
from the front panel of the TD-10, rather than by striking a pad as explained above. You can use
these buttons to select a trigger number and edit the settings.
When you press the button marked “1,” the next lower-numbered trigger will be selected. When
you press the button marked “12,” the next higher-numbered trigger will be selected.
When using a PD-7, PD-9 or PD-120, the rim button ([RIM]) lets you specify whether you are making settings for the head or the rim. When the [RIM] indicator is lit, the rim is selected.
By using these buttons in conjunction with the preview button, you can edit without pads connected
to the TD-10.
* Depending on the instrument selection, there will be no distinction between head and rim in some cases. For
details refer to p. 136.
■ About the Preset Drum Kits
When the instrument is shipped from the factory, drum kits 1–50 are already pre-loaded. Even if
you modify the settings of these drum kits, you can restore them to their factory settings at any time.
These drum kits are referred to as the Preset Drum Kits. For details, refer to p. 137.
■ About the basic screen
fig.00-008ae
This screen is the TD-10’s basic screen, which will appear when you press [KIT].
In addition to the kit name, it displays the status of the memory card (p. 78), the effect on/off setting
(p. 79), and whether or not the kit is for brushes (p. 79) etc.
Screen
name
Drum kit
name
Effect on/off
Settings for brushes
About button operations and the screen displays
20
Quick Start
Quick Start
21
This section explains the connections and settings that you must make before playing. The explanations here are given, assuming that the TD-10 has its factory settings.
The TD-10 provides a function for restoring the factory settings. Refer to “Restoring the factory settings (INITIALIZE)” on p. 137.
Mounting the TD-10 to the stand
Attach the stand holder (included with the optional MDS-7U/10) to the TD-10.
fig.00-009e
Using the included screws, attach it so that the unit is oriented as shown in the above diagram.
Use the included screws. Using other screws can cause damage.
Next, attach the TD-10 to the drum stand (MDS-7U/10).
For details on assembling the drum stand and attaching the TD-10, refer to the owner’s manual for
the drum stand (MDS-7U/10).
To attach the TD-10 to a cymbal stand (or the like), you may want to make use of the separately available
APC-33 All Purpose Clamp.
Make sure, though, that the cymbal stand you intend to use has pipes with a diameter of between 10.5 and 30
millimeters.
MEMO
Narrow
Wide
NOTE
MEMO
Before you begin playing
22
Connect your audio system or amp
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn
off the power on all devices before making any connections.
fig.00-010e
Connect the rear panel MASTER L(MONO) and R jacks to your audio system or amps. If you will be
using headphones, connect them to the PHONES jack.
Be sure that the TD-10’s MASTER L and R jacks are connected respectively to the L and R of your audio system or amps.
In consideration of live performance situations, the headphone output is designed to produce a higher volume
than other electronic musical instruments. Extended listening at high volumes will damage your hearing, so
please pay attention to the volume adjustment.
At the factory settings, no sound will be output from the DIRECT 1, DIRECT 2 or DIRECT 3 jacks.
NOTE
to AC
power outlet
Stereo headphones
Power cord
Audio cable
Audio set, etc.
RL
NOTE
MEMO
Before you begin playing
23
Quick Start
Connecting pads and pedals
Using the cables provided, connect your pads, hi-hat control pedals and kick trigger units as shown
in the above diagram. Special jacks are provided for the kick (KICK) and snare (SNARE), so make
the correct connections to these jacks.
fig.00-011e
Roland
Roland
TD-10 Rear panel
Before you begin playing
24
If you are using a PD-7 or PD-9, move the polarity switch located on the back of the pad to the “-(Roland)”
position. When using a KD-7, either position will do.
fig.00-012
To have the most expressive performance, we recommend the use of the Roland pads (PD-5, PD-7, PD-9, PD100, PD-120) and kick trigger units (KD-7).
NOTE
PD-7, PD-9
OUTPUT POLARITY
+ - (Roland)
MEMO
Before you begin playing
25
Quick Start
Turning on the power
Once the connections have been completed (p. 23, 24), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and
other devices.
fig.00-013
1
Rotate [MASTER] and [PHONES] all the way to the left to turn down the volume.
2
Turn down the volume of the connected amp or audio system.
3
Turn on the POWER switch located on the rear panel of the TD-10.
Caution when turning on the power
● After turning on the power, do not press the hi-hat control pedal (FD-7) until the drum kit
name (see the following illustration) appears in the display.
If the pedal was pressed while the power was being turned on, hi-hat open/close operations cannot be performed correctly.
● After turning on the power, do not strike a pad until the drum kit name appears in the dis-
play.
Striking a pad while the power is being turned on will cause poor response when the pad is struck softly.
fig.00-037
NOTE
5
3
6
1
NOTE
Before you begin playing
26
4
Turn on the power of the connected amp or audio system.
5
Raise the [GROUP FADERS] sliders to the maximum position, and adjust [MASTER] ([PHONES])
to the position shown in the diagram.
fig.00-014a
6
While striking [PREVIEW] with your finger, adjust the volume of the connected amp or audio system. If you are using headphones, gradually raise [PHONES] to adjust the volume.
The TD-10 will produce sound. The volume will depend on the force with which you struck [PRE-
VIEW].
You can use [TRIG SELECT] to select and audition the instrument for each pad.
■ To turn the power off ...
1
Make sure that the TD-10 volume controls and the connected external devices are turned to the
minimum position.
2
Turn off the power of the external devices.
3
Turn off the power of the TD-10.
If there is no sound when you strike [PREVIEW] ...
Check the following points.
· If you are using headphones, are they connected to the PHONES jack?
· If you are using an external amp, is it connected to the MASTER jacks? Are the
audio cables connected correctly to the input jacks of the external amp, etc.?
· Could there be a problem with the cables connected to the external amp?
· Are the input select settings of the external amp correct?
· Are the [GROUP FADERS] sliders lowered?
· Could the [PHONES] volume be too low?
· Could the [MASTER] volume be too low?
MEMO
Before you begin playing
27
Quick Start
Listening to the internal demo playback
The TD-10 contains demo songs that demonstrate its sounds and expressive capabilities. The demo
song is a “rainbow” of 4 short songs, arranged as a medley. It plays back in “loop” (repeating)
mode, yet you can also listen, starting from any of 4 positions, accessed as follows:
fig.00-015
1
Set each of the [GROUP FADERS] sliders [KICK][SNARE][HI-HAT][OTHERS][BACKING] to the
same volume.
2
Hold down [SETUP] and press [CHAIN].
In this display, the cursor defaults to “Rock.”
3
Use [INC/DEC] or the VALUE dial to select the “section” number.
You can start listening from the beginning of any of the four sections.
4
Press [PLAY].
You can listen to the medley and it will continue to loop.
During playback, the [GROUP FADERS] function normally allowing you to mix the demo song as
you wish. (for more info on the [GROUP FADERS], see page 37.)
5
Press [STOP] to stop playback.
Once you are through listening to the demos, press [EXIT] to return to the “DRUM KIT” page.
All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a
violation of applicable laws.
No data for the music that is played will be output from MIDI OUT/THRU.
Drum kit 39–42 are used in the Demo Song.
For details of the Demo Song, refer to page 179.
2
5 4
1
3
NOTE
MEMO
Before you begin playing
28
Specify the pads that the TD-10 will use
In order for the TD-10 to accurately receive trigger signals from each pad, you must specify the type of
pad that is connected to each TRIGGER INPUT jack.
■ If you have purchased the “V-Basic Kit” or “V-Standard Kit”
Trigger settings for the V-Basic Kit or the V-Standard Kit are provided, so you can call up and select
them.
fig.00-016
1
Press [SETUP], press [F1 (TRIG)], and then press [F1 (BANK)].
2
Use [CURSOR] to move the cursor to the “BANK” number.
3
Use [INC/DEC] or the VALUE dial to make the setting.
V-Basic Kit: BANK 1 V-Standard Kit: BANK 2
If the settings have been modified and are different than the settings in the above diagram, use the Copy function to restore the factory settings (p. 137).
This completes settings for all pads of the V-Basic Kit or V-Standard Kit. If you are using a PD-100 or
PD-120, make settings for the head tension as explained on p. 31.
Once you have completed your settings, press [EXIT] enough times to get back to the “DRUM KIT” page.
1 2
3
NOTE
Before you begin playing
29
Quick Start
■ If you have purchased the PD-5, PD-7, PD-9, PD-100 or PD-120
individually
Make the following settings for each pad.
fig.00-023
1
Press [SETUP], press [F1 (TRIG)], and then press [F1 (BANK)].
The following screen will appear:
fig.00-017
This screen shows a list of pad models that are specified
for each TRIGGER INPUT jack.
Display Pad name
PD5 PD-5
PD7 PD-7
PD9 PD-9
10A PD-100
12A PD-120
KD7 KD-7/KD-5
* For details on 10B and 12B, refer to p. 108.
2
Use [CURSOR] to move the cursor to a location other than “BANK.”
3
Strike the pad for which you wish to make settings.
The cursor will move to the edited value of the pad that you struck.
4
Use [INC/DEC] or the VALUE dial to select the model name of the pad.
This completes pad settings. If you are using a PD-100 or PD-120, make settings for the head tension
as explained in the following section.
1 2
4
Before you begin playing
30
Loading...