All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
WARNING:
IMPORTANT:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
THIS APPARATUS MUST BE EARTHED
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
For the U.K.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
USING THE UNIT SAFELY
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
008e
• Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements
and short circuits. Damaged cords are fire and
shock hazards!
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally
or exhibits a marked change in performance.
• If error messages (Error.60, Error.61, Error.62,
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
• Do not force the unit’s power-supply cord to
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
• DO NOT play a CD-ROM disc on a conventional
audio CD player. The resulting sound may be of a
level that could cause permanent hearing loss.
Damage to speakers or other system components
may result.
• Do not put anything that contains water (e.g.,
flower vases) on this unit. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray
cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft
cloth.
• At regular intervals, you should unplug the
power plug and clean it by using a dry cloth to
wipe all dust and other accumulations away from
its prongs. Also, disconnect the power plug from
the power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor insulation
and lead to fire.
• If the unit could become a hazard if it moves, all
caster wheels should be locked or fixed in place
once the unit has been placed at the place of
installation, or has been loaded onto a vehicle.
• If used improperly, batteries may explode or leak
and cause damage or injury. In the interest of
safety, please read and observe the following
precautions (p. 32).
1
• Carefully follow the installation instructions
for batteries, and make sure you observe the
correct polarity.
2
• Avoid using new batteries together with used
ones. In addition, avoid mixing different types
of batteries.
3
• Remove the batteries whenever the unit is to
remain unused for an extended period of time.
5
• If a battery has leaked, use a soft piece of cloth
or paper towel to wipe all remnants of the
discharge from the battery compartment. Then
install new batteries. To avoid inflammation of
the skin, make sure that none of the battery
discharge gets onto your hands or skin.
Exercise the utmost caution so that none of the
discharge gets near your eyes. Immediately
rinse the affected area with running water if
any of the discharge has entered the eyes.
6
• Never keep batteries together with metallic
objects such as ballpoint pens, necklaces,
hairpins, etc.
• Used batteries must be disposed of in compliance
with whatever regulations for their safe disposal
that may be observed in the region in which you
live.
• Be careful when opening/closing the lid so you
do not get your fingers pinched (p. 18). Adult
supervision is recommended whenever small
children use the unit.
• Always keep the following parts including with
the RG-7 and small components that may be
removed out of the reach of small children to
avoid accidental ingestion of these parts.
Included Parts
• Piano leg washers
• Bolts, washers, and springs used in attaching
the pedals
• Cord clamps used for securing pedal cords,
other cord clamps (using double-sided tape),
and cord clamp attachment screws
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2,
3, 4 and 5, please read and observe the following:
Power Supply
301
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a
power supply noise filter between this unit and the
electrical outlet.
306b
• Batteries are supplied with the unit. The life of these
batteries may be limited, however, since their primary
purpose was to enable testing.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
308
• Although the LCD and LEDs are switched off when the
POWER switch is switched off, this does not mean that the
unit has been completely disconnected from the source of
power. If you need to turn off the power completely, first
turn off the POWER switch, then unplug the power cord
from the power outlet. For this reason, the outlet into
which you choose to connect the power cord’s plug
should be one that is within easy reach and readily accessible.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this
unit; or move it farther away from the source of interference.
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
354b
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Also, do not allow lighting devices that normally are used
while their light source is very close to the unit (such as a
piano light), or powerful spotlights to shine upon the
same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
356
• Do not allow rubber, vinyl, or similar materials to remain
on the unit for long periods of time. Such objects can
discolor or otherwise harmfully affect the finish.
358
• Do not allow objects to remain on top of the keyboard.
This can be the cause of malfunction, such as keys ceasing
to produce sound.
359
• Do not paste stickers, decals, or the like to this instrument.
Peeling such matter off the instrument may damage the
exterior finish.
Maintenance
401b (revise)
• Since your piano has a polished finish that is as delicate as
that found on finely crafted wooden furniture, it needs
careful, periodic care. A few important suggestions
concerning the proper care of the unit follow.
• For dusting, using a soft, clean cloth and/or piano-use
feather duster. Be sure to wipe gently. Even the tiniest
grains of sand or grit can leave scratches on the surface
if too much force is applied while wiping.
Do not use any cleaners or detergents, since they might
deteriorate the surface of the cabinet, and produce
cracks.
• If the cabinet’s surface loses its luster, wipe it
thoroughly with a soft cloth dampened with a little of
the polishing liquid.
Do not use any cleaners or detergents, since they might
deteriorate the surface of the cabinet, and produce
cracks. Do not use dusting cloths that contain
chemicals.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
403
• The pedals of this unit are made of brass.\nBrass
eventually darkens as the result of the natural oxidization
process. If the brass becomes tarnished, polish it using
commercially available metal polisher.
Repairs and Data
452
• Please be aware that all data contained in the unit’s
memory may be lost when the unit is sent for repairs.
Important data should always be backed up on a USB
memory, or written down on paper (when possible).
During repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related
to memory itself is out of order), we regret that it may not
be possible to restore the data, and Roland assumes no
liability concerning such loss of data.
6
IMPORTANT NOTES
Automatic Keyboard
Add
• While the automatic keyboard is in operation, avoid doing
anything that could hamper the action of the keys, such as
using undue force to press a key, or forcing up a
depressed key. By doing so, you risk causing malfunction.
Additional Precautions
551
• Please be aware that the contents of memory can be
irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against
the risk of loosing important data, we recommend that
you periodically save a backup copy of important data
you have stored in the unit’s memory on a USB memory.
552
• Unfortunately, it may be impossible to restore the contents
of data that was stored on a USB memory and internal
memory once it has been lost. Roland Corporation
assumes no liability concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
554
• Never strike or apply strong pressure to the display.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
557
•A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559b
• When you need to transport the unit, pack it in shockabsorbent material. Transporting the unit without doing
so can cause it to become scratched or damaged, and
could lead to malfunction.
560
• Do not apply undue force to the music stand while it is in
use.
562
• Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
565
• Before opening or closing the keyboard lid, always make
sure that no pets or other small animals are located on top
of the instrument (in particular, they should be kept away
from the keyboard and its lid). Otherwise, due to the
structural design of this instrument, small pets or other
animals could end up getting trapped inside it. If such a
situation is encountered, you must immediately switch off
the power and disconnect the power cord from the outlet.
You should then consult with the retailer from whom the
instrument was purchased, or contact the nearest Roland
Service Center.
Before Using USB Memory
Using USB Memory
704 (revised)
• When connecting USB memory, make sure to press it until
it is fully inserted.
705 (revised)
• Never touch the terminals of the USB memory. Also,
avoid getting the terminals dirty.
708 (revised)
• USB memories are constructed using precision components; handle the cards carefully, paying particular note to
the following.
• To prevent damage to the cards from static electricity,
be sure to discharge any static electricity from your
own body before handling the cards.
• Do not touch or allow metal to come into contact with
the contact portion of the cards.
• Do not bend, drop, or subject cards to strong shock or
vibration.
• Do not keep cards in direct sunlight, in closed vehicles,
or other such locations (storage temperature: 0 to 50˚
C).
• Do not allow cards to become wet.
• Do not disassemble or modify the cards.
Add
• Insert the USB memory in the Ext Memory port evenly
and without undue force. Forcing the USB memory may
damage the Ext Memory port.
Add
• Do not insert any object other than the USB memory (e.g.,
wires, coins, other types of disks, etc.) in the Ext Memory
port. This may damage the Ext Memory port.
Add
• Do not subject the Ext Memory port cover or connected
USB memory to excessive stress.
Add
• Close the USB memory cover when using the USB
memory for extended periods
7
IMPORTANT NOTES
Before Using CDs
Handling the CD Drive
Add
• Avoid using the unit immediately after it has been moved
to a location with a level of humidity that is greatly
different than its former location. Rapid changes in the
environment can cause condensation to form inside the
drive, which will adversely affect the operation of the
drive and/or damage discs. When the unit has been
moved, allow it to become accustomed to the new
environment (allow a few hours) before operating it.
Add
• Remove any disc from the drive before powering up or
down.
Add
• To avoid the risk of malfunction and/or damage, insert
only discs with into the CD drive. Never insert any other
type of disc. Avoid getting paper clips, coins, or any other
foreign objects inside the drive.
Add
• Do not subject to vibrations or physical shock during use,
and do not move the unit while the power is turned on.
Add
• The pickup is of dust-resistant construction. Do not use
pickup cleaners or other such materials, as they may
damage the pickup.
* GS () is a registered trademark of Roland Corpo-
ration.
209
* Mac OS is a trademark of Apple Computer, Inc.
Add
* XG lite () is a registered trademark of Yamaha
Corporation.
220
* All product names mentioned in this document are
trademarks or registered trademarks of their
respective owners.
Handling the CDs
Add
• When handling the discs, please observe the following.
• Do not touch the recorded surface of the disc.
• Do not use in dusty areas.
• Do not leave the disc in direct sunlight or an enclosed
vehicle.
801
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean
using a commercially available CD cleaner.
Add
• Keep the disc in the case.
Add
• Do not keep the disc in the CD drive for a long time.
Add
• Do not put a sticker on the label of the disc.
Add
• Wipe the disc with a soft and dry cloth radially from
inside to outside. Do not wipe along circumference.
Add
• Do not use benzine, record cleaner spray or solvents of
any kind.
Add
• Do not bend the disc. Bending discs may prevent proper
reading and writing of data, and may further result in
malfunction.
8
Introduction
Thank you, and congratulations on your choice of the Roland RG-7 Digital Grand Piano.
The RG-7 is sure to be highly appreciated, not only for the authentic piano performances it offers, but also for
its extensive selection of player piano functions.
In order to enjoy reliable performance of your new keyboard for many years to come, please take the time to
read through this manual in its entirety.
Main Features
Piano Sounds with Rich Resonance and Wide-Ranging Expressiveness
The stereo sampling piano sound generator realistically reproduces even the sound of the hammers striking
the strings, producing the tones of a high-quality concert grand piano.
Maximum polyphony of 128 notes ensures that you can use the pedal freely without running out of notes.
Roland Digital Grand Brings Refinement to Interior Style
The RG-7 exhibits elegance in form with a beautiful black, mirror-like surface. With features just like those
found on an acoustic grand, such as a lid that opens and closes and retractable music rest, this instrument is
a perfect match for lounge or living room.
The simple, modern, and stylish panel design makes switching tones and making settings a snap.
Full Complement of Player Piano Functions
The RG-7 comes programmed with song data in jazz and classical styles. You can also use the CD drive to play
back a wide variety of music on the CD included with the instrument as well as songs on CD-ROMs
containing saved SMF files, player piano CDs, and audio CDs. Moreover, you can add song data by copying
songs saved on USB memory and CD-ROMs to the RG-7’s “Favorites.”
The RG-7 includes a “Moving Key” function, which plays the keys along with the song, providing exquisite
performances that are played automatically.
Also included is a convenient remote control you can use for selecting songs, adjusting volume, switching the
Moving Key function on and off simply and easily. You can connect an external display or television set to the
RG-7 for enlarged displays of the Song Select screen, karaoke screen (lyrics screen), notation, and even slide
shows.
Instrument Endowed with Superior Basic Functions
The RG-7 uses the progressive hammer action keyboard, which reproduces the touch of a grand piano, with
a heavier feel in the lower registers and a lighter, quicker response in the upper registers. This keyboard also
accurately reproduces the distinctive clicking feel that occurs when the keys are played gently (escapement
mechanism).
The instrument further is equipped with highly responsive pedals, which lend even greater expressive detail
to your performances.
The RG-7 also is programmed with 20 carefully selected performance tones, including two types of grand
piano tones, which you can select according to your own taste. What’s more, the settings for the “key touch,”
“hammer response,” and other precision tone adjustment settings that performers demand can be stored in
the RG-7 itself.
On top of this, a newly designed sound system puts the focus on the sound of the piano to achieve a luscious,
natural piano sound.
9
Introduction
Professional-Level Features and Specifications
The instrument features a lid lock to prevent unauthorized operation of the controls or keys while the Moving
Key function is in use, and an Ext Memory port lock to prevent theft of connected USB memory.
Since the RG-7 is a digital instrument, it has no strings and therefore requires no tuning.
You can connect an external display or television to the piano to run slide shows using whatever images you
prefer and, with a microphone connected, you can add echo and harmonies to microphone vocals and use the
Transformer function to change the sound of the vocals.
Connect External Speakers to Produce Concert Hall Presence
You can connect an amp and speakers to the RG-7 and play the sounds of the reverb and accompaniment
through the external speakers to produce the effect of being enveloped by an orchestra.
The RG-7 is equipped with XLR connectors, a very convenient feature when the instrument is used on stage.
■
Conventions Used in This Manual
This manual uses the following conventions in the interest of simpler, more concise instructions.
• Button names are enclosed in square brackets “[ ]”, as in [Moving Key] button.
• An asterisk (*) or a at the beginning of a paragraph indicates a note or precaution.
NOTE
These should not be ignored.
• (p. **) refers to pages within the manual.
10
Contents
USING THE UNIT SAFELY.......................................................................................................... 3
IMPORTANT NOTES ................................................................................................................... 6
Main Features.............................................................................................................................................. 9
Conventions Used in This Manual ............................................................................................. 10
Front Panel................................................................................................................................................. 14
Jack Panel (Left Side of Bottom Panel) ..................................................................................................15
CD Drive (Right Side of Bottom Panel)................................................................................................. 16
Before You Start Playing......................................................................17
Opening and Closing the Top ................................................................................................................ 17
Raising the Music Rest............................................................................................................................. 18
Extending the Music Rest ............................................................................................................ 18
Opening and Closing the Lid ................................................................................................................. 18
Using the Lid Lock........................................................................................................................ 18
Connect the Pedal Cord........................................................................................................................... 19
Connecting the Power Cord.................................................................................................................... 19
Turning the Power On and Off .............................................................................................................. 19
Adjusting the Sound’s Volume and Brilliance.....................................................................................20
About the Pedals....................................................................................................................................... 20
Connecting a Microphone....................................................................................................................... 21
Connecting USB Memory........................................................................................................................ 22
Connecting the Memory .............................................................................................................. 22
About the Screens..................................................................................................................................... 23
Main Screens .................................................................................................................................. 23
Adjusting the Contrast of the Screen.......................................................................................... 23
Chapter 1. Playing Back Songs ...........................................................24
Look at What You Can Do with the RG-7! ........................................................................................... 24
Listening to Songs ....................................................................................................................................25
Tone List .................................................................................................................................................. 107
Internal Song List.................................................................................................................................... 108
Parameters Stored to Internal Memory............................................................................................... 109
Parameters Stored in Memory Backup .................................................................................... 109
Parameters Stored in the User Program ..................................................................................109
Music Files That the RG-7 Can Use ..................................................................................................... 110
The RG-7 allows you to use the following music files........................................................... 110
About the RG-7 Sound Generator ............................................................................................ 110
Main Specifications ................................................................................................................................112
They are used to choose the kinds of tones (tone groups)
played by the keyboard (p. 53).
[Piano 1] button
[Piano 2] button
[Harpsichord] button
[Vibraphone] button
[E.Piano] button
5.
Display
Tone and song names and the values of various settings
are displayed here (p. 23).
6.
[Function] (Exit) button
This switches the RG-7 to the Function screen (p. 88).
You can make various different settings in the Function
screen, including settings for the master tuning and
temperaments.
5
678910 11
[] (Select +) button
8.
Press this button while the Song Select screen is
displayed to select the previous song (p. 26, p. 28, p. 31).
When the Function screen is displayed, this button is
used to select the item for which settings are to be made
(p. 88).
[] (Value -) button
9.
Press this button while the Song Select screen is
displayed to start and stop playback of the song (p. 26, p.
28, p. 31).
Press this button while the Function screen is displayed
to change the value of a setting (p. 88).
[] (Value +) button
10.
Press this button while the Song Select screen is
displayed to select the next song (p. 26, p. 28, p. 31).
Press this button while the Function screen is displayed
to change the value of a setting (p. 88).
[Moving Key] (Enter) button
11.
This switches the automatic keyboard feature on and off
(p. 88). This feature provides keyboard movement
corresponding to the song being played back.
Additionally, press this button when the Function screen
is displayed to make even more advanced settings.
7.
[Song] (Select -) button
This displays the Song Select screen (p. 23). The song
genre is switched each time you press this button while
the Song Select screen is displayed (p. 25).
When the Function screen is displayed, this button is
used to select the item for which settings are to be made
(p. 88).
14
Jack Panel (Front)
1234567
Panel Descriptions
Jack Panel (Rear)
8
91012
11
Jack Panel (Left Side of Bottom Panel)
1.
Phones jacks
A set of headphones can be connected here (p. 21).
Mic Volume knob
2.
Adjusts the volume level for the microphone (p. 21).
Mic jack
3.
Used for connecting microphones (p. 21).
4.
Aux Input jack
You can connect other sound generating devices or
audio equipment here and have their sound be played
through the RG-7’s speakers (p. 36).
5.
MIDI Out/In connectors
Connect to external MIDI devices to exchange
performance data (p. 99).
USB connector
6.
You can connect a computer and exchange performance
data between the instrument and the computer (p. 103).
LCD Contrast knob
7.
This adjusts the brightness of the front panel display (p.
23).
8.
AC Inlet
Connect the included power cord to this inlet (p. 19).
10.
Input jacks
You can connect other sound generating devices or
audio equipment here and have their sound be played
through the RG-7’s speakers (p. 97).
11.
Aux Output jacks
You can connect amps and external speakers here and
play accompaniment or surround sound (p. 98).
Main Output jacks
12.
These jacks can be connected to your audio system to
enjoy more powerful sound (p. 97).
13.
Balanced Out (Fixed) jacks
This provides balanced audio signal output. Connect a
mixer or other such device here (p. 97).
Video Out jack
14.
Connect a television here. This allows you to display the
Song Select screen, slide show, lyrics, and notations on
the connected television set (p. 49).
Ext Display connector
15.
Connect a external display here. You can display the
Song Select screen, slide show, lyrics, and notations on
the external display (p. 47).
131415
Pedal connector
9.
Connect the pedal cord here (p. 19).
15
Panel Descriptions
CD DriveBottom of CD Drive
54
21 3
3
CD Drive (Right Side of Bottom Panel)
Access Indicator
1.
This indicator will light when the inserted CD is being
read.
2.
Disc Tray
Place the CD to be loaded on this tray (p. 29).
3.
Emergency Eject Hole
This hole allows the disc tray to be opened in case of an
emergency (p. 29).
4.
Eject Button
Press this button to eject the CD (p. 29).
* You cannot eject the CD unless the RG-7’s power is turned
on.
Infrared Receiver
5.
Point the remote control at this sensor when using the
remote control to operate the RG-7 (p. 33).
Ext Memory Port
6.
You can connect USB memory (sold separately) here (p.
22).
7.
Ext Memory Port Cover
You can ensure the cover remains closed when you have
USB memory connected (p. 22).
* Be sure to close the cover of the Ext Memory port after
connecting USB memory to the Ext Memory port. If the cover
is left open, someone could get hurt if their legs bump into it;
the cover could be damaged as well.
Ext Memory Port Cover Lock
8.
You can lock the Ext Memory port cover to prevent theft
of the USB memory device connected to the theft
Memory port (p. 22).
8
6
7
16
Before You Start Playing
A
While holding up the top with one hand, lift up the top
Opening and Closing the Top
Opening only the front top
3.
stick and insert its end into the appropriate top slip.
fig.
D
Children must not be permitted to open or close the top
on their own—adult supervision is required. Because the
top is very heavy, always use two or more people when
opening and closing the top, and be sure to handle it
carefully.
Lift the right front (the upper note side: A in the figure)
1.
of the board with both hands, fold it back, and then lay
it down slowly on the top.
fig.
C
Do not move the piano with the top in the open position.
The top stick may disengage from the socket, causing the
top to fall.
When opening the top, be careful not to open it too far.
Opening the top at an angle in excess of 30 degrees may
damage the unit, or cause the top to drop. Also, before
opening the top, make sure that no one is in the path of
the top as it is opened.
Opening both the front top and the top
2.
Follow Step 1 to open the front top. Then lift the right
front (the upper note side B: in the figure) of the board
with both hands.
fig.
B
About the Topsticks and Topslip
The RG-7 has two topsticks, each a different length.
You can use the different topsticks to change the amount the
top is left open.
fig.
Long top stick
Short top stick
The following describes the fitting of the lid props and their
corresponding topslips.
The long top stick: for inner top slip (C)
The short top stick: for outer top slip (D)
If you use the wrong top slip, the top stick could slip out
of the top slip, causing the top to fall. Make sure that the
end of the top stick is inserted securely into the top slip.
To close the top, reverse the opening procedure.
17
Before You Start Playing
Raising the Music Rest
fig.
1.
Open the front top (p. 17).
Hold the music rest with both hands, then raise it
2.
forward.
3.
While supporting the music rest with one hand, adjust
the angle of the music rest with the brace behind the
music rest.
Opening and Closing the Lid
fig.
1.
To open the lid, hold handles with both hands and lift
it straight up. Then, slide it to the rear.
To close the lid, hold handles with both hands and
2.
slowly pull it forward until it stops. Then, gently lower
it into place.
When opening and closing the lid, be careful not to let
your fingers get caught. Small children should use it
only under the supervision of an adult.
■
Extending the Music Rest
The music rest can be pulled forward to make your sheet
music easier to read.
1.
When extending the music rest, be sure to grasp the
music rest with both hands and gently pull it forward.
fig.
When moving the piano, for safety’s sake be sure to close
the lid first.
NOTE
Make sure you don’t have anything (such as sheet
music) on the keyboard when you close the lid.
■
Using the Lid Lock
You can lock the keyboard lid with the lid covering the
control panel (front panel) to prevent it from being opened,
thus avoiding inadvertent changes during automatic
performances.
Lower the lid until the control panel (the front panel) is
1.
covered.
2.
Turn the lid lock under the piano as shown in the
figure below to lock the lid.
Lid Lock released
Pulling the music rest too far forward may cause it to
separate and fall; be sure not to overextend the music
rest.
18
Lid Lock engaged
Before You Start Playing
NOTE
Using undue force to open the lid when it is locked may
damage the lid and/or the lock.
Turning the lid lock when the lid lock is released while
the keyboard lid is open may make the keyboard lid
prone to closing. Always confirm that the keyboard lid is
covering the control panel before locking the lid.
Connecting the Pedal Cord
1.
Connect the pedal cord to the Pedal jack located in the
jack panel on the lower left of the RG-7.
fig.00-01
Turning the Power On and
Off
NOTE
Turn on power to your various devices in the order
specified. By turning on devices in the wrong order, you
risk causing malfunction and/or damage to speakers
and other devices.
To turn the power on, turn the [Volume] knob all the
way down, and then press the [Power] switch.
When you turn on the power to the RG-7, the front panel
display appears as shown below.
After a few seconds, you will be able to play the
keyboard to produce sound.
Use the [Volume] knob to adjust the volume.
Connecting the Power Cord
1.
Connect the supplied power cord to the AC inlet.
2.
Connect the pedal cord to the Pedal connector.
3.
Cramp the power cord and pedal cord with Cord
Cramp and screw at A, B, and C (see the picture
above).
b
a
NOTE
This unit is equipped with a protection circuit. A brief
interval (a few seconds) after power up is required
before the unit will operate normally.
To turn the power off, turn the [Volume] knob all the
way to the left, and press the [Power] switch.
The front panel display goes blank, and the power is
turned off.
* If you need to turn off the power completely, first turn off the
POWER switch, then unplug the power cord from the power
outlet. Refer to “Power Supply” (p. 6).
a
Screw
b
Cord Cramp
Plug the power cord into an AC outlet.
4.
19
Before You Start Playing
Adjusting the Sound’s
Volume and Brilliance
Turn the [Volume] knob to adjust the overall volume.
Turn the [Brilliance] knob to adjust the brightness of
the sound.
fig.00-07.e
The mark at the top of the [Volume] knob indicates the
volume level typically produced by an acoustic piano.
This is usually the most appropriate volume for your
piano performances.
You can adjust the volume with the remote control. For
details, refer to “About the Remote Control” (p. 34).
About the Pedals
The pedals have the following functions, and are used
mainly for piano performance.
fig.00-08.e
Soft Pedal
Sostenuto Pedal
Damper pedal (right pedal)
While this pedal is pressed, notes will be sustained even after
you take your fingers off the keys.
On an acoustic piano, holding down the damper pedal will
allow the remaining strings to resonate in sympathy with the
sounds that you played from the keyboard, adding a rich
resonance.
The RG-7 simulates this Damper Resonance.
Damper Pedal
You can change the amount of resonance applied with
the damper pedal. Please refer to “Producing the
Resonance of the Strings When the Keys Are Played
(Damper Resonance)” (p. 59).
Sostenuto pedal (center pedal)
This pedal sustains only the sounds of the keys that were
already played when you pressed the pedal.
Soft pedal (left pedal)
When you hold down this pedal and play the keyboard, the
sound will have a softer tone.
The softness of the tone can be varied subtly by the depth to
which you press the pedal.
You can assign functions to the left and center pedals.
Refer to “Assigning Functions to Pedals” (p. 69).
20
Before You Start Playing
Connecting Headphones
The RG-7 has two jacks for plugging in headphones. This
allows two people to listen through headphones
simultaneously, making it very useful for lessons and
performing piano pieces for four hands. Additionally, this
allows you to play without bothering others around you,
even at night.
fig.00-04.e
Connecting a Microphone
You can connect a microphone into the Mic jack, and enjoy
karaoke with the RG-7.
fig.00-10
1.
Plug the headphones into the Phones jack located in
the jack panel on the lower left of the RG-7.
Connecting headphones will automatically mute the
sound from the internal speakers.
The headphone volume is adjusted by the [Volume]
knob of the RG-7.
NOTE
Use Stereo headphones.
Some Notes on Using Headphones
• To prevent damage to the cord, handle the headphones
only by the headset or the plug.
• Connecting the headphones when the volume of
connected equipment is turned up may result in damage
to the headphones. Lower the volume on the RG-7
before plugging in the headphones.
• Listening at excessively high volume levels will not only
damage the headphones, but may also cause hearing
loss. Use the headphones at a moderate volume level.
Connect a microphone (sold separately) to the Mic jack
1.
located in the jack panel on the lower left of the RG-7.
2.
Rotate the Mic Volume knob in front of the Mic jack to
adjust the volume level for the microphone.
3.
Adjust the mic echo (p. 39).
Some Notes on Using a Microphone
• Be careful of high volume levels when using microphone
late at night or early in the morning.
• When connecting a microphone to the RG-7, be sure to
lower the volume. If the volume control is too high when
the microphone is plugged in, noise may be produced by
the speakers.
• Howling could be produced depending on the location
of microphones relative to speakers. This can be
remedied by:
- Changing the orientation of the microphone.
- Relocating microphone at a greater distance from
speakers.
- Lowering volume levels.
21
Before You Start Playing
Ext Memory
Por t Cover
Connecting USB Memory
You can connect USB memory (sold separately) to the RG-7’s
Ext Memory port. Connecting external USB memory enables
you to do the following:
• Play back songs stored on the USB memory device.
• Save songs recorded on the RG-7 to the USB memory
device.
• Copy songs in the USB memory device to the RG-7’s User
memory, allowing the songs to be called up simply and
easily.
• The images saved to the USB memory are displayed as a
slide show.
■
Connecting the Memory
NOTE
Always be sure to use the following procedure when
connecting USB memory.
1.
Press the Ext Memory port cover located under the CD
drive to open the cover.
Press on the front part of the Ext Memory port cover to
3.
close the cover.
NOTE
Use USB memory available from Roland. Proper
operation cannot be guaranteed if other external
memory products are used.
Locking the Ext Memory Port Cover
You can lock the Ext Memory port cover to prevent theft of
the USB memory device (sold separately) connected to the
Ext Memory port.
Connect the USB memory device (refer to previous
1.
section).
Press on the front part of the Ext Memory port cover to
2.
close the cover.
Press the front of the cover to open it.
Connect the USB memory to Ext Memory port.
2.
3.
Using a screwdriver, remove the anti-theft lock screws
(two screws) to the side of the Ext Memory port.
Screw
22
Ext Memory
Por t
Anti-theft
Lock
Secure the anti-theft lock with the screws as shown
4.
below.
Screws
Before You Start Playing
About the Screens
Immediately after the power is turned on, the Song Select
screen like the one below is displayed.
■
Main Screens
Song Select Screen
When you press the [Song] button, the following screen is
displayed. Each time you press the [Song] button in this
screen, the song genre is switched.
Function Screen
Press the [Function] (Exit) button; the indicator lights, and
the following screen appears.
NOTE
Be sure to replace removed screws when securing the
anti-theft lock.
Tone Screen
Press the Tone button; the indicator lights, and the following
screen appears.
■
Adjusting the Contrast of the
Screen
Rotate the LCD Contrast knob on the jack panel at the
1.
lower left of the instrument.
23
Chapter 1. Playing Back Songs
Look at What You Can Do with the RG-7!
Listen to the Internal Songs
The various internal songs programmed in the RG-7 are categorized into “Jazz” and
“Classical” genres. You can play back the songs in these genres in a variety of ways,
playing all the songs in sequence or randomly, or just playing songs individually.
Listen to the Included CD and Commercial Audio CDs
You can use the RG-7’s CD drive to play the included CD, CD-ROMs containing
saved SMF music files, commercial audio CDs, and player piano CDs.
Listen to Songs Saved to USB Memory
Not only can you play CDs, you can also play back SMF music files saved on USB
memory. In addition, you can connect USB memory and copy song data recorded
with the RG-7 to the USB memory.
Store Songs in the “Favorites”
The RG-7 is set at the factory with tone demos registered in the “Favorites.” Listen
to the tone demos to check out the special characteristics of each tone.
Additionally, you can save songs recorded with the RG-7 to the “Favorites” and you
can copy songs stored in USB memory to the “Favorites” as well. Songs held in the
“Favorites” are not lost when the power is turned off, making this a convenient place
to store those songs you listen to often.
Easy-to-Use Remote Control Included
You can use the included remote control to start and stop the current performance
and switch songs. You can also use the remote control to select what is to be
displayed on an external screen or television set connected to the RG-7 and assign
other functions to the remote control’s buttons to make operating the RG-7 even
simpler.
Connect a Microphone for Karaoke Performances
Connect a microphone to the RG-7, and you are ready to enjoy karaoke. You can
change the key of the song to match the singer’s voice and adjust the amount of echo
applied to the microphone input. In addition, the RG-7 includes functions for adding
harmonies and effects (Transformer) to vocals.
Show Your Favorite Images on a Connected Display or Television
You can connect an external display or television set to the RG-7 and display the
Song Select screen, lyrics and notations, and even slide shows of your favorite
images. You can also use the remote control to switch the images appearing in the
connected external display or television.
The “Moving Key” Feature
You can have the RG-7’s keyboard play automatically along with the internal songs,
songs recorded with the RG-7, songs on CDs, and songs stored in USB memory. You
can switch this feature on and off with the [Moving Key] button on the front panel
or with the buttons on the remote control.
24
Listening to Songs
The RG-7 features a variety of internal songs. The internal songs are categorized into
“Jazz” and “Classical” genres.
You can also use the RG-7’s CD drive to play back the included CD, CD-ROMs with
songs saved in SMF format, commercially available audio CDs, and player piano
CDs. Moreover, you can connect USB memory to the Ext Memory port and play back
SMF music file that’s been saved on the memory device.
■
[Song] Button Functions
Each press of the [Song] button selects the next available song genre, in this order:
“Jazz” → “Classical” → “Favorites” → “CD” → “Ext Memory” (songs in the USB
memory device connected to the Ext Memory port)
fig.
Chapter 1. Playing Back Songs
The “CD” and “USB” genres appear only when a CD is in the CD drive or when USB
memory is connected to the Ext Memory port. “Favorites” is indicated only when
there are songs in the Favorites genre.
What are the “Favorites?”
This is the area of memory where you can save copies of performances recorded with
the RG-7, songs saved on CD-ROMs, songs stored in the USB memory connected to
the RG-7’s Ext Memory port, and other songs.
After copying songs to the “Favorites,” you can then select the copied songs simply
by pressing the [Song] button and selecting “Favorites” as the song genre.
The RG-7 features a User Memory (the RG-7’s memory) area where the following
types of data are stored.
• Content registered in the “Favorites”
• Content set in User programs (Favorites performance settings) (p. 78)
To delete the content of the User Memory and restore the memory to the default
factory settings, refer to “Initializing the User Memory or USB Memory” (p. 92).
You can select and listen to tone demos (p. 26) from the “Favorites” after initializing
the User memory.
You can also delete these tone demos and overwrite them with other songs, which
can then be saved.
25
Chapter 1. Playing Back Songs
b
■
Listening to the Tone Demos
The factory settings have tone demos registered in the “Favorites” (p. 25).
1.
Press the [Song] button one or more times to select “Favorites” as the
genre.
2.
Press the [] button to start playback of the tone demos.
You can select the tone demo to play back by pressing the [] or [] button.
3.
Press the [] button once more to stop playback of the tone demos.
You can delete tone demos in the “Favorites” and overwrite them by saving other
songs in their place. If you want to play back tone demos after they have been
deleted, initialize the User Memory to restore the factory settings (p. 92).
■
Listening to the Internal Songs
NOTE
Songs saved to the “Favorites”
are deleted when the User
Memory is initialized. Save
any songs you want to retain
y copying them to USB
memory (p. 42).
Press the [Song] button one or more times to select the genre you want.
1.
The internal song genres are “Jazz” and “Classical.”
fig.
If using the remote control, press the remote control’s [INTERNAL] button. The
internal song genre selection can be switched between “Jazz” and “Classical” by
pressing the [INTERNAL] button.
“Jazz” → “Classical” → “Jazz”....
Press the [] button to start playback of the internal songs.
2.
Songs in the selected genre are played back.
When the RG-7 is set to play back all songs (p. 27), once the song currently being
played back is finished, the next song starts playing automatically. After all of the
songs in the genre have been played, playback automatically resumes from the first
song in the genre. When the RG-7 is set to play back a single song (p. 27), playback
stops automatically when the song is finished.
For more information on the
[Song] button functions, refer
to “[Song] Button Functions”
(p. 25).
NOTE
If any previously recorded
song data is present, the
message “Delete User Song
OK?” appears in the display. If
you want to delete the existing
song data, press the [Moving
Key] (Enter) button. If you do
not want the song data to be
deleted, press the [Function]
(Exit) button, and save the
song to the “Favorites” or to
your USB memory (p. 76).
You can select the next song by pressing the [] button, and return to the
beginning of the song or the previous song by pressing the [] button.
3.
Press the [] button once more to stop playback of the internal songs.
26
When playing songs on CDs,
refer to “Listening to Songs on
CDs” (p. 28).
When playing songs from a
USB memory device connected
to the Ext Memory port, refer
to “Playing Back Songs from
USB Memory” (p. 31).
Playing Back One Song
To play a single selected song, use the following procedure.
1.
Press the [Function] (Exit) button, getting its indicator to light.
2.
Press the [Song] (Select -) button or [] (Select +) button to display
the PLAY screen.
fig.
3.
Press the [Song] (Select -) button or [] (Select +) button to get the
value for “Mode” to flash.
fig.
Chapter 1. Playing Back Songs
You can save this setting in the
RG-7’s memory using the
Memory Backup function (p.
72).
Press the [] (Value -) button or [] (Value +) button to select
4.
“One Song.”
Value
All of the songs in the genre are played back in sequence,
All Song
One Song
5.
Press the [Function] (Exit) button so the indicator goes out.
starting from the selected song. When the final song in the
selected genre is finished playing, playback then
automatically resumes from the first song in that genre.
Only the selected song is played.
Playback stops when the song is finished.
Description
27
Chapter 1. Playing Back Songs
■
Listening to Songs on CDs
Cautions
Handling CDs
• Do not leave discs exposed to direct sunlight for extended periods.
• Handle CDs with your finger and thumb, holding the disc by the center hole and
outer rim. Do not touch or scratch the disc’s recording surface (the green side).
• Do not drop or stack discs.
• Do not place heavy objects on discs or subject them to strong impact.
• Do not affix stickers or other such materials on the label side. Placing stickers on
the disc may result in errors when data writing and scratch the disc.
• Use a felt-tip marker or other soft-tipped implement to write titles and other
information on the label side of discs.
• Store discs in their original cases or other suitable cases for protection.
• Before using the CD, please read the warning on the CD cover.
Cleaning Discs
• If a disc becomes dusty or soiled, gently wipe the disc with a soft cloth. Always
wipe outwards from the center using light, gentle strokes. Do not wipe the disk
in a circular pattern.
Precautions Concerning Use of the CD
• CD-R/RW discs to which audio tracks have been added, and CDs with mixed
audio tracks and data will not play back properly.
• The RG-7 is capable of playing back only commercial CDs that conform the
official standards-those that carry the “COMPACT DISC DIGITAL AUDIO”
logo. The usability and sound quality of audio discs that incorporate copyright
protection technology and other non-standard CDs cannot be guaranteed.
• For more detailed information on audio discs featuring copyright protection
technology and other non-standard CDs, please consult the disc vendor.
• You cannot save songs and styles to CDs, and you cannot delete songs or styles
recorded to CDs. Furthermore, you cannot format CDs.
• The prescribed format for CD-R/RW discs is “ISO9660 Level 1 Mode 1.”
• You may be unable to read using other formats.
CDs That Can Be Played Back
• Commercially available audio CDs
• CD-ROMs containing saved SMF music files
• CD included with the RG-7
• Player piano CDs
28
Insert the CD in the CD Drive
If a disc tray does not open
If the power is turned off with the disc still in the drive (such as due to a power
failure), the disc tray cannot be opened by pressing the eject button. In this case, you
can insert a piece of wire to force the tray open.
fig.
Press the eject button and open a disc tray.
1.
fig.
Disc Tray
2.
Put a CD on a disc tray.
3.
Press the eject button again to close the disc tray.
Removing a CD
1.
Press the eject button and open a disc tray.
Chapter 1. Playing Back Songs
Eject Button
2.
Remove the CD from the disc tray.
Emergency Eject Hole
Make sure the RG-7’s power has been turned OFF before attempting to engage the
emergency eject hole. If you insert something while the power is on, the disc could
be damaged, or unexpected problems may occur.
Playing Back Songs on CDs
You can play back the CD included with the RG-7, CDs with player piano CDs,
audio CDs, and CD-ROMs to which SMF music files are saved.
1.
Place the CD you want to play in the CD drive.
2.
Press the [Song] button one or more times to select “CD” as the genre.
If using the remote control, press the remote control’s [EXTERNAL] button, then
select “CD” as the genre.
29
Loading...
+ 92 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.