Roland Corporation RD-700GX User's Manual

■

●

❍

Digital Piano

Model: RD-700GX

MIDI Implementation

1. Receive data

Channel Voice Messages

Note off

Status

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = note number: 00H - 7FH (0 - 127)

vv = note off velocity: 00H - 7FH (0 - 127)

* Some instruments are not received in Rhythm set.

Note on

Status

9nH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = note number: 00H - 7FH (0 - 127)

vv = note on velocity: 01H - 7FH (1 - 127)

Control Change

Bank Select (Controller number 0, 32)

Status

BnH 00H mmH

BnH 20H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)

* Not received when the Rx Bank Select (EDIT: Part Parameter: Rx Bank Select) is OFF.

* The SETUP, Rhythms, and Tones corresponding to each Bank Select are as follows.

* The SRX series corresponding to each Bank Select are to see the SRX series owner’s

manual.

-----+---------+-----------+----------------------+---------- 000 | | 001 - 128 | GM Tone | : | | | | 032 | | 001 - 128 | GM Tone | 085 | 000 | 001 - 100 | SETUP | 001 - 100 086 | 064 | 001 - 005 | Rhythm Set | 263 - 267 087 | 064 | 001 - 026 | Tone (PIANO) | 001 - 026 | 065 | 001 - 021 | Tone (E.PIANO) | 037 - 057 | 066 | 001 - 031 | Tone (CLAV/MALLET) | 058 - 088 | 067 | 001 - 022 | Tone (ORGAN) | 099 - 120 | 068 | 001 - 026 | Tone (STRINGS) | 121 - 146 | 069 | 001 - 024 | Tone (PAD) | 147 - 170 | 070 | 001 - 038 | Tone (GTR/BASS) | 171 - 208 | 071 | 001 - 028 | Tone (BRASS/WINDS) | 209 - 236 | 072 | 001 - 026 | Tone (VOICE/SYNTH) | 237 - 262 | : | | : | 092 | 000 - | 001 - | SRX Rhythm | 001 | : | | : | 093 | 000 - | 001 - | SRX Patch | 001 | : | | : | 112 | 000 | 001 - 010 | TW-Organ | 089 - 098 113 | 000 | 001 - 010 | S.NaturlEP | 027 - 036 120 | | 001 - 057 | GM2 Rhythm | 268 - 276 121 | 000 - | 001 - 128 | GM2 Tone | 277 - 532

Modulation (Controller number 1)

Status

BnH 01H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Modulation depth: 00H - 7FH (0 - 127)

* Not received when the Rx Modulation (EDIT: Part Parameter: Rx Modulation) is OFF.

Portamento Time (Controller number 5)

Status 2nd byte 3rd byte

BnH 05H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Portamento Time: 00H - 7FH (0 - 127)

* The Portament Time parameter (Tone Info: Portament Time) will change.

2nd byte 3rd byte

Date: Feb. 1, 2008

Version: 1.00

Data Entry (Controller number 6, 38)

Status

BnH 06H mmH

BnH 26H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = the value of the parameter specified by RPN/NRPN

mm = MSB, ll = LSB

Volume (Controller number 7)

Status 2nd byte 3rd byte

BnH 07H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Volume: 00H - 7FH (0 - 127)

* Not received when the Rx Volume (EDIT: Part Parameter: Rx Volume) is OFF.

* The Part Level parameter will change.

Panpot (Controller number 10)

Status

BnH 0AH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Panpot: 00H - 40H - 7FH (Left - Center - Right),

* Not received when the Rx Pan (EDIT: Part Parameter: Rx Pan) is OFF.

* The pan parameter (EDIT: Part Parameter: Pan) will change.

Expression (Controller number 11)

Status

BnH 0BH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Expression: 00H - 7FH (0 - 127)

General Purpose Controller 1 (Controller number 16)

Status 2nd byte 3rd byte

BnH 10H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127)

Hold 1 (Controller number 64)

Status

BnH 40H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH

* Not received when the Rx Hold-1 (EDIT: Part Parameter: Rx Hold-1) is OFF.

Portamento (Controller number 65)

Status

BnH 41H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

* The Portamento Sw parameter (Tone Info: Portament Sw) will change.

Sostenuto (Controller number 66)

Status 2nd byte 3rd byte

BnH 42H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

Soft (Controller number 67)

Status 2nd byte 3rd byte

BnH 43H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127)

Legato Foot Switch (Controller number 68)

Status

BnH 44H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

2nd byte 3rd byte

❍

●

MIDI Implementation

Resonance (Controller number 71)

Status

BnH 47H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv= Resonance value (relative change): 00H - 7FH (-64 - 0 - +63)

* The Resonanse parameter (Tone Info: Resonance) will change.

2nd byte 3rd byte

Release Time (Controller number 72)

Status 2nd byte 3rd byte

BnH 48H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63)

* The Release Time parameter (Tone Info: Release Time) will change.

Attack time (Controller number 73)

Status

BnH 49H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63),

* The Attack Time parameter (Tone Info: Attack Time) will change.

2nd byte 3rd byte

Cutoff (Controller number 74)

Status

BnH 4AH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Cutoff value (relative change): 00H - 7FH (-64 - 0 - +63)

* The Cutoff parameter (Tone Info: Cutoff) will change.

2nd byte 3rd byte

Decay Time (Controller number 75)

Status 2nd byte 3rd byte

BnH 4BH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Decay Time value (relative change): 00H - 7FH (-64 - 0 - +63)

* The Decay parameter (Tone Info: Decay) will change.

Vibrato Rate (Controller number 76)

Status

BnH 4CH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Vibrato Rate value (relative change): 00H - 7FH (-64 - 0 - +63)

2nd byte 3rd byte

Vibrato Depth (Controller number 77)

Status

BnH 4DH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)

2nd byte 3rd byte

Vibrato Delay (Controller number 78)

Status 2nd byte 3rd byte

BnH 4EH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)

Portamento Control (Controller number 84)

Status 2nd byte 3rd byte

BnH 54H kkH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = source note number: 00H - 7FH (0 - 127)

* A Note-on received immediately after a Portamento Control message will change

continuously in pitch, starting from the pitch of the Source Note Number.

* If a voice is already sounding for a note number identical to the Source Note Number,

this voice will continue sounding (i.e., legato) and will, when the next Note-on is

received, smoothly change to the pitch of that Note-on.

* The rate of the pitch change caused by Portamento Control is determined by the

Portamento Time value.

Effect 1 (Reverb Send Level) (Controller number 91)

Status

BnH 5BH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Reverb Send Level: 00H - 7FH (0 - 127)

* The Reverb Amount parameter (Tone Info: Reverb Amount) will change.

2nd byte 3rd byte

Effect 3 (Chorus Send Level) (Controller number 93)

Status 2nd byte 3rd byte

BnH 5DH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Chorus Send Level: 00H - 7FH (0 - 127)

* The Chorus Amount parameter (Tone Info: Chorus Amount) will change.

RPN MSB/LSB (Controller number 100, 101)

Status

BnH 65H mmH

BnH 64H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm = upper byte (MSB) of parameter number specified by RPN

ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are extended.

When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any

order) should be sent in order to select the parameter, then Data Entry (Controller numbers

6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry

messages that is received at the same MIDI channel after that are recognized as changing

toward the value of the RPN messages. In order not to make any mistakes, transmitting

RPN Null is recommended after setting parameters you need.

This device receives the following RPNs.

RPN Data entry

MSB, LSB MSB, LSB Notes

00H, 00H mmH, llH Pitch Bend Sensitivity

00H, 01H mmH, llH Channel Fine Tuning

00H, 02H mmH, llH Channel Coarse Tuning

00H, 05H mmH, llH Modulation Depth Range

7FH, 7FH ---, --- RPN null

2nd byte 3rd byte

mm: 00H - 18H (0 - 24 semitones)

ll: ignored (processed as 00H)

Up to 2 octave can be specified in semitone steps.

* The Bend Range parameter (Tone Info: Bend Range) will

change.

mm, ll: 20 00H - 40 00H - 60 00H

(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)

* The Fine Tune parameter (Tone Info: Fine Tune) will

change.

mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)

ll: ignored (processed as 00H)

* The Coarse Tune parameter (Tone Info: Coarse Tune)

will change.

mm, ll: 00 00H - 06 00H ( 0 - 16384 x 600 / 16384 cent)

RPN and NRPN will be set as “unspecified.” Once this

setting has been made, subsequent Parameter values that

were previously set will not change.

mm, ll: ignored

Program Change

Status

CnH ppH

n = MIDI channel number: 0H - FH (ch.1 - 16)

pp = Program number: 00H - 7FH (prog.1 - prog.128)

* Not received when the Rx Program Change parameter (EDIT: Part Parameter: Rx

Program Chanage) is OFF.

2nd byte

●

■

●

■

●

■

●

❍

MIDI Implementation

Pitch Bend Change

Status

EnH llH mmH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Not received when the Rx Bender parameter (EDIT: Part Parameter: Rx Bender) is OFF.

2nd byte 3rd byte

Channel Mode Messages

All Sounds Off (Controller number 120)

Status

BnH 78H 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* When this message is received, all notes currently sounding on the corresponding

channel will be turned off.

Reset All Controllers (Controller number 121)

Status

BnH 79H 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* When this message is received, the following controllers will be set to their reset values.

Controller Reset value

Pitch Bend Change ±0 (center)

Channel Pressure 0 (off)

Modulation 0 (off)

Breath Type 0 (min)

Expression 127 (max)

Hold 1 0 (off)

Sostenuto 0 (off)

Soft 0 (off)

Hold 2 0 (off)

RPN unset; previously set data will not change

NRPN unset; previously set data will not change

All Notes Off (Controller number 123)

Status 2nd byte 3rd byte

BnH 7BH 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* When All Notes Off is received, all notes on the corresponding channel will be turned

off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are

turned off.

OMNI OFF (Controller number 124)

Status

BnH 7CH 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* The same processing will be carried out as when All Notes Off is received.

OMNI ON (Controller number 125)

Status

BnH 7DH 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* The same processing will be carried out as when All Notes Off is received. OMNI ON

will not be turned on.

MONO (Controller number 126)

Status 2nd byte 3rd byte

BnH 7EH mmH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm = mono number: 00H - 10H (0 - 16)

* The same processing will be carried out as when All Notes Off is received.

* The Mono/Poly parameter (Tone Info: Mono/Poly) will change.

2nd byte 3rd byte

POLY (Controller number 127)

Status

BnH 7FH 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* The same processing will be carried out as when All Notes Off is received.

* The Mono/Poly parameter (Tone Info: Mono/Poly) will change.

2nd byte 3rd byte

System Realtime Message

Timing Clock

Status

F8H

* This message will be received if the Clock Source parameter (EDIT: SYSTEM: Clock

Source) is EXT.

Active Sensing

Status

FEH

* When Active Sensing is received, the unit will begin monitoring the intervals of all

further messages. While monitoring, if the interval between messages exceeds 420 ms,

the same processing will be carried out as when All Sounds Off, All Notes Off and Reset

All Controllers are received, and message interval monitoring will be halted.

System Exclusive Message

Status

F0H iiH, ddH, ......,eeH F7H

F0H: System Exclusive Message status

ii = ID number: an ID number (manufacturer ID) to indicate the manufacturer whose

dd,...,ee = data: 00H - 7FH (0 - 127)

F7H: EOX (End Of Exclusive)

Of the System Exclusive messages received by this device, the Universal Non-realtime

messages and the Universal Realtime messages and the Data Request (RQ1) messages and

the Data Set (DT1) messages will be set automatically.

Universal Non-realtime System Exclusive Messages

Identity Request Message

Status Data byte Status

F0H 7EH, dev, 06H, 01H F7H

Byte Explanation

F0H Exclusive status

7EH ID number (Universal Non-realtime Message)

dev Device ID (dev: 10H - 1FH (1 - 32), the initial value is 10H (17))

06H Sub ID#1 (General Information)

01H Sub ID#2 (Identity Request)

F7H EOX (End Of Exclusive)

* When this message is received, Identity Reply message (p. 8) will be transmitted.

GM1 System On

Status

F0H 7EH, 7FH, 09H, 01H F7H

Byte Explanation

F0H Exclusive status

7EH ID number (Universal Non-realtime Message)

7FH Device ID (Broadcast)

09H Sub ID#1 (General MIDI Message)

01H Sub ID#2 (General MIDI 1 On)

F7H EOX (End Of Exclusive)

Data byte Status

Exclusive message this is. Roland’s manufacturer ID is 41H.

ID numbers 7EH and 7FH are extensions of the MIDI standard;

Universal Non-realtime Messages (7EH) and Universal Realtime

Messages (7FH).

Data byte Status

* Not received when the Rx GM/GM2 System On parameter (EDIT: System: Rx GM/GM2

System ON) is OFF.

❍

●

❍

●

❍

MIDI Implementation

GM2 System On

Status F0H 7EH 7FH 09H 03H F7H

Byte Explanation F0H Exclusive status 7EH ID number (Universal Non-realtime Message) 7FH Device ID (Broadcast) 09H Sub ID#1 (General MIDI Message) 03H Sub ID#2 (General MIDI 2 On) F7H EOX (End Of Exclusive)

* Not received when the Rx GM/GM2 System On parameter (EDIT: System: Rx GM/GM2

System ON) is OFF.

Data byte Status

GM System Off

Status Data byte Status F0H 7EH, 7F, 09H, 02H F7H

Byte Explanation F0H Exclusive status 7EH ID number (Universal Non-realtime Message) 7FH Device ID (Broadcast) 09H Sub ID#1 (General MIDI Message) 02H Sub ID#2 (General MIDI Off) F7H EOX (End Of Exclusive)

* Not received when the Rx GS Reset parameter (EDIT: System: Rx GS Reset) is OFF.

Universal Realtime System Exclusive Messages

Master Volume

Status F0H 7FH, 7FH, 04H, 01H, llH, mmH F7H

Byte F0H Exclusive status 7FH ID number (universal realtime message) 7FH Device ID (Broadcast) 04H Sub ID#1 (Device Control) 01H Sub ID#2 (Master Volume) llH Master Volume lower byte mmH Master Volume upper byte F7H EOX (End Of Exclusive)

* The lower byte (llH) of Master Volume will be handled as 00H. * The Master Volume parameter (EDIT: System: Master Volume) will change.

Master Fine Tuning

Status F0H 7FH, 7FH, 04H, 03H, llH, mmH F7H

Byte F0H Exclusive status 7FH ID number (universal realtime message) 7FH Device ID (Broadcast) 04H Sub ID#1 (Device Control) 03H Sub ID#2 (Master Fine Tuning) llH Master Fine Tuning LSB mmH Master Fine Tuning MSB F7H EOX (End Of Exclusive) mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.9 [cents])

Master Coarse Tuning

Status Data byte Status F0H 7FH, 7FH, 04H, 04H, llH, mmH F7H

Byte F0H Exclusive status 7FH ID number (universal realtime message) 7FH Device ID (Broadcast) 04H Sub ID#1 (Device Control) 04H Sub ID#2 (Master Coarse Tuning) llH Master Coarse Tuning LSB mmH Master Coarse Tuning MSB F7H EOX (End Of Exclusive)

Data byte Status

Explanation

Data byte Status

Explanation

Global Parameter Control

Reverb Parameters

Status

F0H 7FH, 7FH, 04H, 05H, 01H, 01H, F7H

Byte Explanation

F0H Exclusive status

7FH ID number (universal realtime message)

7FH Device ID (Broadcast)

04H Sub ID#1 (Device Control)

05H Sub ID#2 (Global Parameter Control)

01H Slot path length

01H Parameter ID width

01H Value width

01H Slot path MSB

01H Slot path LSB (Effect 0101: Reverb)

ppH Parameter to be controlled.

vvH Value for the parameter.

F7H EOX (End Of Exclusive)

Chorus Parameters

Status

F0H 7FH, 7FH, 04H, 05H, 01H, 01H, F7H

Byte Explanation

F0H Exclusive status

7FH ID number (universal realtime message)

7FH Device ID (Broadcast)

04H Sub ID#1 (Device Control)

05H Sub ID#2 (Global Parameter Control)

01H Slot path length

01H Parameter ID width

01H Value width

01H Slot path MSB

02H Slot path LSB (Effect 0102: Chorus)

ppH Parameter to be controlled.

vvH Value for the parameter.

F7H EOX (End Of Exclusive)

Data byte Status

01H, 01H, 01H, ppH, vvH

pp=0 Reverb Type

vv = 00H Small Room

vv = 01H Medium Room

vv = 02H Large Room

vv = 03H Medium Hall

vv = 04H Large Hall

vv = 08H Plate

pp=1 Reverb Time

vv = 00H - 7FH 0 - 127

Data byte Status

01H, 01H, 02H, ppH, vvH

pp=0 Chorus Type

vv=0 Chorus1

vv=1 Chorus2

vv=2 Chorus3

vv=3 Chorus4

vv=4 FB Chorus

vv=5 Flanger

pp=1 Mod Rate

vv= 00H - 7FH 0 - 127

pp=2 Mod Depth

vv = 00H - 7FH 0 - 127

pp=3 Feedback

vv = 00H - 7FH 0 - 127

pp=4 Send To Reverb

vv = 00H - 7FH 0 - 127

ll: ignored (processed as 00H) mm: 28H - 40H - 58H (-24 - 0 - +24 [semitones])

❍

●

❍

MIDI Implementation

Channel Pressure

Status

F0H 7FH, 7FH, 09H, 01H, 0nH, ppH, rrH F7H

Byte

F0H Exclusive status

7FH ID number (universal realtime message)

7FH Device ID (Broadcast)

09H Sub ID#1 (Controller Destination Setting)

01H Sub ID#2 (Channel Pressure)

0nH MIDI Channel (00 - 0F)

ppH Controlled parameter

rrH Controlled range

F7H EOX (End Of Exclusive)

Data byte Status

Explanation

pp=0 Pitch Control

rr = 28H - 58H -24 - +24 [semitones]

pp=1 Filter Cutoff Control

rr = 00H - 7FH -9600 - +9450 [cents]

pp=2 Amplitude Control

rr = 00H - 7FH 0 - 200%

pp=3 LFO Pitch Depth

rr = 00H - 7FH 0 - 600 [cents]

pp=4 LFO Filter Depth

rr = 00H - 7FH 0 - 2400 [cents]

pp=5 LFO Amplitude Depth

rr = 00H - 7FH 0 - 100%

Controller

Status

F0H 7FH, 7FH, 09H, 03H, 0nH, ccH, ppH, rrH F7H

Byte

F0H Exclusive status

7FH ID number (universal realtime message)

7FH Device ID (Broadcast)

09H Sub ID#1 (Controller Destination Setting)

03H Sub ID#2 (Control Change)

0nH MIDI Channel (00 - 0F)

ccH Controller number (01 - 1F, 40 - 5F)

ppH Controlled parameter

rrH Controlled range

F7H EOX (End Of Exclusive)

Data byte Status

Explanation

pp=0 Pitch Control

rr = 28H - 58H -24 - +24 [semitones]

pp=1 Filter Cutoff Control

rr = 00H - 7FH -9600 - +9450 [cents]

pp=2 Amplitude Control

rr = 00H - 7FH 0 - 200%

pp=3 LFO Pitch Depth

rr = 00H - 7FH 0 - 600 [cents]

pp=4 LFO Filter Depth

rr = 00H - 7FH 0 - 2400 [cents]

pp=5 LFO Amplitude Depth

rr = 00H - 7FH 0 - 100%

Scale/Octave Tuning Adjust

Status Data byte Status

F0H 7EH, 7FH, 08H, 08H, ffH, ggH, hhH, ssH... F7H

Byte

F0H Exclusive status

7EH ID number (Universal Non-realtime Message)

7FH Device ID (Broadcast)

08H Sub ID#1 (MIDI Tuning Standard)

08H Sub ID#2 (scale/octave tuning 1-byte form)

ffH Channel/Option byte 1

ggH Channel byte 2

hhH Channel byte 3

ssH 12 byte tuning offset of 12 semitones from C to B

F7H EOX (End Of Exclusive)

Explanation

bits 0 to 1 = channel 15 to 16

bit 2 to 6 = Undefined

bits 0 to 6 = channel 8 to 14

bits 0 to 6 = channel 1 to 7

00H = -64 [cents]

40H = 0 [cents] (equal temperament)

7FH = +63 [cents]

Key-based Instrument Controllers

Status

F0H 7FH, 7FH, 0AH, 01H, 0nH, kkH, nnH, vvH F7H

Byte Explanation

F0H Exclusive status

7FH ID number (universal realtime message)

7FH Device ID (Broadcast)

0AH Sub ID#1 (Key-Based Instrument Control)

01H Sub ID#2 (Controller)

0nH MIDI Channel (00 - 0F)

kkH Key Number

nnH Control Number

vvH Value

F7 EOX (End Of Exclusive)

* This parameter affects drum instruments only.

Data byte Status

nn=07H Level

vv = 00H - 7FH 0 - 200% (Relative)

nn=0AH Pan

vv = 00H - 7FH Left - Right (Absolute)

nn=5BH Reverb Send

vv = 00H - 7FH 0 - 127 (Absolute)

nn=5D Chorus Send

vv = 00H - 7FH 0 - 127 (Absolute)

Data Transmission

This instrument can use exclusive messages to exchange many varieties of internal settings

with other devices.

The model ID of the exclusive messages used by this instrument is 00H 00H 2BH.

Data Request 1 RQ1 (11H)

This message requests the other device to transmit data. The address and size indicate the

type and amount of data that is requested.

When a Data Request message is received, if the device is in a state in which it is able to

transmit data, and if the address and size are appropriate, the requested data is transmitted

as a Data Set 1 (DT1) message. If the conditions are not met, nothing is transmitted.

Status

F0H 41H, dev, 00H, 00H, 2BH, 11H, aaH, bbH, ccH, F7H

Byte Remarks

F0H Exclusive status

41H ID number (Roland)

dev Devdevice ID (dev: 10H - 1FH, 7FH)

00H Model ID #1 (RD-700GX)

00H Model ID #2 (RD-700GX)

2BH model ID #3 (RD-700GX)

11H Command ID (RQ1)

aaH Address MSB

bbH Address

ccH Address

ddH Address LSB

ssH Size MSB

ttH Size

uuH Size

vvH Size LSB

sum Checksum

F7H EOX (End Of Exclusive)

* The size of data that can be transmitted at one time is fixed for each type of data. And

data requests must be made with a fixed starting address and size. Refer to the address

and size given in

* For the checksum, refer to 14 page.

data byte status

ddH, ssH, ttH, uuH, vvH, sum

“Parameter Address Map”

(p. 9).

+ 9 hidden pages