R® |
Factory Reset Procedures |
|
|
Caution: Many of these procedures will erase all memory in the unit. Make sure you have backed up any data you wish to keep before performing these procedures! If a unit is not listed here, it does not have an initialization procedure that is user-executable.
A
Model |
Procedure |
|
|
A-30/33/37 |
Power on while holding WRITE. (Hold for 15 seconds) |
|
|
A-50/80 |
While holding the first, third, and fourth buttons under the display, press CHANNEL. Then |
|
press any cursor button |
A-70/90/90EX |
Power on while holding down MANUAL, then press ENTER |
|
|
A-220 |
Power on while holding B and MEMORY |
|
|
A-300PRO |
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. |
|
|
A-500PRO |
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. |
|
|
A-500S |
Hold MIDI CH and PGM CHANGE, press the SYSTEM key, Use the VALUE dial to select |
|
“SY6,” press ENTER 3 times. |
A-800PRO |
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. |
|
|
A-880 |
Power on while holding SIGNAL and MEMORY |
|
|
AD-8 |
Power on while holding WRITE. Confirm that “F” flashes in the display, then release |
|
WRITE. Press WRITE again |
AP-700 |
Power on, then press EXIT repeatedly to get ANALYZER/FILTER screen. Cursor to MENU, |
|
press ENTER. Cursor to SYSTEM, press ENTER. Cursor to INITIALIZE, press ENTER. Use |
|
VALUE to select ALL MEMORY, then press ENTER twice |
AT-Series |
(Make sure disk drive is empty.) Power on while holding ONE TOUCH PROGRAM |
|
|
AX-09 |
Power on while holding FAVORITE A, B, and WRITE. Press TONE 5, then press WRITE. |
|
|
AX-1/7 |
Power on while holding WRITE. (Hold for 30 seconds) |
|
|
AXIS-1 |
While holding FUNCTION, press the F#0, C#2, and D#2 keys |
|
|
AX-Synth |
Power on while holding INC/+, DEC/-, and TONE 7(ORGAN/CLAVI), then press WRITE. |
|
|
B |
|
Model |
Procedure |
|
|
BR-8/532/1180 |
Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice |
|
|
BR-600 |
Power on while holding GUITAR, MIC, and LINE. Press ENTER. |
|
|
BR-800 |
Press MENU. Cursor to “Factory Reset.” Press ENTER three times. |
|
|
BR-864 |
Power on while holding INPUT SELECT/GUITAR/BASS, MIC, and LINE. Press ENTER |
|
|
BR-900CD/ |
Press UTILITY. Press CURSOR Right to select “Initialize.” Press ENTER. Press CURSOR |
1200CD |
Right to select “All.” Press ENTER twice |
BR-1600CD |
Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice |
|
|
C |
|
Model |
Procedure |
|
|
CD-2 |
Press MENU. Use the DATA dial to select “INITIALIZE.” Press ENTER twice. |
|
|
CD-2E/2i |
Press MENU. Use the < / > buttons to select “Factory Reset.” Press ENTER twice. |
|
|
CDX-1 |
Press UTILITY. Cursor right to “INIT”. Press ENTER/YES. Use CURSOR buttons to select |
|
desired target to be initilaized, (GLOBAL, FX, MIXER, ALL). Press ENTER/YES twice |
CE-20 |
Power on while holding WRITE. Release WRITE then press WRITE again |
|
|
CR-80 |
Power on while holding DEL and REPEAT, then press ENTER |
|
|
D |
|
Model |
Procedure |
|
|
D-2 |
With the unit on, Hold WRITE and press SYSTEM. Press ENTER twice |
|
|
DB-30 |
Power on while holding the START/STOP button until “F” shows in the display |
|
|
DB-60 |
Power on while holding the MEMORY button until “F” shows in the display |
|
|
DB-88 |
Power on while holding METRONOME MODE and LOOP MODE. Press WRITE |
|
|
DB-90 |
Power on while holding MEMORY |
|
|
DD-20 |
Power on while holding WRITE. Release, then press WRITE again |
|
|
©2010 Roland Corporation U.S. |
Page 1 |
|
R® |
Factory Reset Procedures |
|
|
||
|
|
|
|
|
|
|
|
DDR-30 |
|
Power on while holding the #1 button |
|
||
|
|
|
||||
|
|
|
|
|
||
|
DEP-3/5 |
|
Power on while holding MEMORY NO UP (^) and DOWN (v) |
|
||
|
|
|
|
|
||
|
DJ-70/70MKII |
|
Power on while holding the UP ARROW button to enter test mode. Press A, press C, press |
|
||
|
|
|
S1. When finished the screen will display IC21 = OK |
|
||
|
DR-3 |
|
Press EDIT. CURSOR Right to select “SYSTEM.” Press ENTER. CURSOR Right to select |
|
||
|
|
|
<FACTORY RESET>. Press ENTER twice |
|
||
|
DR-5 |
|
Power on while holding FRET LEFT (<) and RIGHT (>), then press ENTER twice |
|
||
|
|
|
|
|
||
|
DR-202 |
|
Power on while holding MUTE and ROLL. Press TAP/ENTER. Cursor to “YES” in the |
|
||
|
|
|
display. Press TAP/ENTER |
|
|
|
|
DR-550/550MKII |
|
Power on while holding -1 and +1, |
then press START |
|
|
|
|
|
|
|
||
|
DR-660 |
|
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [8] INIT. Press ENTER twice |
|
||
|
|
|
|
|
||
|
DR-670 |
|
Power on while holding REC and STOP / CONT. Press ENTER twice |
|
||
|
|
|
|
|
||
|
DR-770 |
|
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [9] F. RST. Press ENTER twice |
|
||
|
|
|
|
|
||
|
DR-880 |
|
Press EDIT. Press CURSOR Right to select “Factory Reset.” Press ENTER twice |
|
||
|
|
|
|
|
||
|
DS-330 |
|
Power on while holding REVERB and SPLIT, then press YES |
|
||
|
|
|
|
|
|
|
|
E |
|
|
|
|
|
|
Model |
|
Procedure |
|
|
|
|
|
|
|
|
||
|
E-09 |
|
Press FUNCTION so it is lit. Use the FAMILY </> buttons to select “Utility,” then use the |
|
||
|
|
|
SELECT </> buttons to select “Factory Reset.” Press TEMPO >/YES twice |
|
||
|
E-10/20/30 |
|
Power on while holding WRITE |
|
|
|
|
|
|
|
|
||
|
E-35 |
|
Power on while holding REC/PUNCH IN |
|
||
|
|
|
|
|
|
|
|
E-36 |
|
Power on while holding RECORDER |
|
|
|
|
|
|
|
|
||
|
E-50/60/80 |
|
Press MENU. Press “UTILITY” then press “FACTORY RESET.” Press “EXECUTE.” |
|
||
|
|
|
|
|
|
|
|
E-56 |
|
Power on while holding WRITE |
|
|
|
|
|
|
|
|
||
|
E-66 |
|
Power on while holding REC in the DISK RECORDER section |
|
||
|
|
|
|
|
|
|
|
E-68/70/86/96 |
|
Power on while holding WRITE |
|
|
|
|
|
|
|
|
||
|
E-300/500 |
|
Press UTILITY. Use the buttons under the display that correspond to <<PAGE>> to |
|
||
|
|
|
select FACTORY PRESET. Press EXECUTE, then press OK. When the screen displays |
|
||
|
|
|
RESET COMPLETE, turn the unit off, then on |
|
||
|
E-600 |
|
Press FUNCTION and use the PAGE (<) (>) buttons to select “Factory Preset.” Touch the |
|
||
|
|
|
“Execute” icon followed by the “OK” icon on the display screen. Power off then on |
|
||
|
EG-101 |
|
Power on while holding WRITE |
|
|
|
|
|
|
|
|
||
|
EM-10 |
|
Power on while holding USER PROGRAM/WRITE |
|
||
|
|
|
|
|
||
|
EM-15/25 |
|
With the unit on, press FUNCTION until “RESUME” shows in the display. Then press |
|
||
|
|
|
TEMPO+ |
|
|
|
|
EM-20/30/50/55 |
|
Power on while holding USER PROGRAM/WRITE |
|
||
|
|
|
|
|
||
|
EM-2000 |
|
Performance Sets need to be loaded from disk to restore factory default settings. Insert |
|
||
|
|
|
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press |
|
||
|
|
|
PAGE ^ / v to select “PRF MEM” and press UPPER 1(Execute) |
|
||
|
ep-5/7/7MKII |
|
While holding REC and PLAY, press STRINGS. Power off and then back on |
|
||
|
|
|
|
|
||
|
ep-9 |
|
While holding REC and PLAY, press CHOIR. Power off and then back on |
|
||
|
|
|
|
|
|
|
|
ep-75/85 |
|
Power on while holding REC |
|
|
|
|
|
|
|
|
||
|
EQ-20 |
|
Power on holding LIGHT and SELECT. Release, then press LIGHT and SELECT again |
|
||
|
|
|
|
|
||
|
EXR-3/5 |
|
Power on while holding USER PROGRAM/WRITE |
|
||
|
|
|
|
|
||
|
EXR-40/46OR |
|
Power on while holding USER PROGRAM/WRITE |
|
||
|
|
|
|
|
|
|
|
F |
|
|
|
|
|
|
Model |
|
Procedure |
|
|
|
|
|
|
|
|||
|
F-110 |
|
Hold REVERB and press TRANSPOSE, hold OTHERS and use the +/- buttons to select |
|
||
|
|
|
“Fct” in the display. Press the Stop/Start button twice. |
|
||
|
Fantom |
|
With the unit on, press MENU. Press the UP or DOWN cursor buttons to select FACTORY |
|
||
|
|
|
RESET. Press 8 (EXECUTE) twice |
|
|
|
|
Fantom-G6/7/8 |
|
Press MENU. Use the CURSOR Up and Down buttons to select “Factory Reset,” then press |
|
||
|
|
|
F8 [Select] followed by F7 [OK]. Press F7 [OK] when completed. |
|
©2010 Roland Corporation U.S. |
Page 2 |
|
R® |
Factory Reset Procedures |
|
|
||
|
|
|
|
|
|
|
|
Fantom-S/S88 |
|
Press MENU. Use the CURSOR Up or Down buttons to select “Utility,” then press ENTER. |
|
||
|
|
|
||||
|
|
|
Press 3 (Factory Reset) Press 8 (Execute) |
|
||
|
Fantom-Xa |
|
Press EXIT. Press MENU. Turn the VALUE dial to select “Utility” and then press ENTER. |
|
||
|
|
|
Press F3. Press F6 |
|
|
|
|
Fantom-XR |
|
Press MENU. Press CURSOR Down to select “UTILITY.” Press ENTER. Press CURSOR |
|
||
|
|
|
Down to select “FACTORY RESET.” Press ENTER twice |
|
||
|
Fantom-X6/7/8 |
|
Press MENU. Press the CURSOR DOWN button to select “Utility.” Press button 3 (Factory |
|
||
|
|
|
Reset). Press Button 8 (Exec). Cycle the power |
|
||
|
FC-100MKII |
|
Power on while holding pedals #1, #2, and #8 |
|
||
|
|
|
|
|
||
|
FC-200 |
|
Power on while holding the #10 pedal, then press the CTL pedal |
|
||
|
|
|
|
|
||
|
FG-10/1000 |
|
Power on while holding CLEAR and EXIT |
|
||
|
|
|
|
|
||
|
FP-2 |
|
Power on while holding REVERB until “Fct” shows in the display |
|
||
|
|
|
|
|
||
|
FP-4 |
|
Power on while holding FUNCTION |
|
||
|
|
|
|
|
||
|
FP-5 |
|
Power on while holding PEDAL CONTROL |
|
||
|
|
|
|
|
||
|
FP-7 |
|
Power on while holding FUNCTION |
|
||
|
|
|
|
|
||
|
FP-8 |
|
Press FUNC and release. While holding PIANO, press FUNC again |
|
||
|
|
|
|
|
||
|
FR-3 |
|
Power on while holding SET and ORCHESTRA. |
|
||
|
|
|
|
|
||
|
FR-5/7 |
|
Power on while holding MENU/WRITE. Press the DATA/ENTER button |
|
||
|
|
|
|
|
|
|
|
G |
|
|
|
|
|
|
Model |
|
Procedure |
|
|
|
|
|
|
|
|
||
|
G-70 |
|
Press MENU. Touch UTILITY, then touch FACTORY RESET. Touch EXECUTE |
|
||
|
|
|
|
|
||
|
G-600/800 |
|
Power on while holding WRITE |
|
||
|
|
|
|
|
||
|
G-1000 |
|
Performance Sets need to be loaded from disk to restore factory default settings. Insert |
|
||
|
|
|
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press |
|
||
|
|
|
PAGE ^ / v to select “PRF MEM” and press UPPER 1 (Execute) |
|
||
|
GI-10 |
|
Power on while holding PARAMETER + and -, then press VALUE + |
|
||
|
|
|
|
|
||
|
GI-20 |
|
With the power off, set the GUITAR /BASS switch to match the instrument you are using. |
|
||
|
|
|
Power on while holding TUNER(STRING SEL). Press WRITE |
|
||
|
GM-70 |
|
Poly Mode: Power on while holding PLAY, GENERAL EDIT, and IND EDIT. |
|
||
|
|
|
Mono Mode: Power on while holding TUNE, CONTROL ASSIGN, and DATA TRANSFER |
|
||
|
GP-16 |
|
Power on while holding the #6, #7, and #8 buttons. Use the FUNCTION LEFT (<) and |
|
||
|
|
|
RIGHT (>) buttons to select “2.All Factory Preset,” then press WRITE three times |
|
||
|
GP-20 |
|
Power on while holding WRITE. Release WRITE, (The MEMORY indicator will flash), then |
|
||
|
|
|
press WRITE again |
|
|
|
|
GP-100 |
|
Power on while pressing in the PARAMETER knob, then press WRITE |
|
||
|
|
|
|
|
||
|
GR-09 |
|
Power on while holding Pedal #2, then press the VALUE + button. Now press EDIT/PLAY |
|
||
|
|
|
|
|
||
|
GR-1 |
|
Power on while holding WRITE/COPY, then press YES |
|
||
|
|
|
|
|
||
|
GR-20 |
|
Power on while holding WRITE, then press WRITE again |
|
||
|
|
|
|
|
|
|
|
GR-30 |
|
Power on while holding |
Pedal #2, then press the PATCH+ button to select INI. Press |
|
|
|
|
|
EDIT/PLAY. Then press PATCH+ and PATCHsimultaneously |
|
||
|
GR-33 |
|
Press SYSTEM. Press PARAMETER (>) right to select “FACTORY RESET”. Use VALUE to |
|
||
|
|
|
select “ALL”. Press WRITE twice |
|
||
|
GS-10 |
|
Power on while holding the CHANNEL SELECT A and B buttons (within the |
|
||
|
|
|
PREAMP/SPEAKER section), then press WRITE |
|
||
|
GT-3 |
|
Power on while holding MOD and SFX. Press WRITE |
|
||
|
|
|
|
|
||
|
GT-5 |
|
Power on while holding MOD and FEEDBACKER/SLOW GEAR. Press WRITE |
|
||
|
|
|
|
|
||
|
GT-6/8/Pro |
|
Power on while holding the PREAMP ON/OFF and (PREAMP)TYPE/VARIATION buttons. |
|
||
|
|
|
Press WRITE |
|
|
|
|
GT-6B |
|
Power on while holding COMP/LIMITER ON/OFF and TYPE VARIATION. Press WRITE |
|
||
|
|
|
|
|
||
|
GT-10/10B |
|
Press SYSTEM. CURSOR right to select “FACTORY RESET” then press ENTER twice. |
|
||
|
|
|
|
|
||
|
GW-7 |
|
Press FUNCTION. Press SELECT Left or Right to choose “Utility.” Press ENTER twice |
|
||
|
|
|
|
|
||
|
GW-8 |
|
Press MENU. Use the CURSOR Up and Down buttons to select “Utility” then press ENTER. |
|
||
|
|
|
Use the CURSOR buttons to select “Factory Reset” then press ENTER twice. Power off and |
|
||
|
|
|
on. |
|
|
|
|
GX-700 |
|
Press TUNER/UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) buttons to select FACT |
|
||
|
|
|
|
|
|
|
©2010 Roland Corporation U.S. |
Page 3 |