Roland Corporation GK-KIT-GT3 Owner's Manual

Instruction Manual
Thank you for purchasing the Roland GK-KIT-GT3, a divided pickup kit. The GK-KIT-GT3 is a specialized kit for internal installation of the guitar divided pickup. To ensure proper installation – which is critical – and operation, please read this manual carefully.
IMPORTANT NOTES
In addition to the items listed under “USING THE UNIT SAFELY,” please read and observe the following:
351
Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum.
352b
Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing.
402
Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
556
When connecting / disconnecting all wirings, grasp the connector itself---never pull on the cable. This way you will avoid causing shorts, or damage to the cable's internal elements.
901
To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the board.
• Before you touch the board, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged.
• When handling the board, grasp it only by its edges. Avoid touching any of the electronic components or connectors.
• Before you connect any cables, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been in contact with a carpet (or other object) where there is a static electricity buildup.
• Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it.
911
Do not touch any of the printed circuit pathways.
912
Never use excessive force when installing a circuit board.
913
When circuit board installation is complete, double-check your work.
915
Install only the included circuit boards. Remove only the specified screws.
962a
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Roland assumes no liability concerning any damage to the guitar and GK-KIT-GT3 upon installing the GK-KIT-GT3. Please proceed with the installation using cation and care at your own risk.
Be sure to use the special cable supplied by us to connect the GK­KIT-GT3 to the GK-compatible device for guitar. Use of any other cable may cause unnecessary problems.
GK-KIT-GT3 cannot be used with guitars that have unusual or customized string setups, or guitars strung with nylon, rubber, or other non-metallic strings.
901(F)
Veuillez suivre attentivement les instructions suivantes quand vous manipulez la carte afin d'éviter tout risque d'endom­magement des pièces internes par l'électricité statique.
• Toujours toucher un objet métallique relié à la terre (comme un tuyau par exemple) avant de manipuler la carte pour vous décharger de l'électricité statique que vous auriez pu accumuler.
• Lorsque vous manipulez la carte, la tenir par les côtés. Évitez de toucher aux composants ou aux connecteurs.
• Avant de connecter tout câble, assurez-vous qu'il ne contient aucune charge d'électricité statique. De telles charges peuvent être transmises, par exemple, si l'autre extrémité du câble touche à un tapis (ou autre objet) où il y a accumulation d'électricité statique.
• Conservez le sachet d'origine dans lequel était la carte lors de l'envoi et remettez la carte dedans si vous devez la ranger ou la transporter.
911(F)*
Ne toucher aucun chemin d'accès des cicuits imprimés.
912(F)
Ne jamais forcer lors de l'installation de la carte de circuits imprimés.
913(F)
Quand l'installation de la carte de circuits imprimés est terminée, revérifiez si tout est bien installé.
914(F)
Avant d'entreprendre l'installation de cette unité, retirer les piles de la guitare le cas échéant.
915(F)
Installer uniquement les carte de circuits imprimés ci-jointes. Enlevez seulement les vis indiquées.
Supplied parts contents
• Divided Pickup ........................................................................................1
• Preamp Board...........................................................................................1
• GK Connector Board................................................................................1
• Connector Plate ........................................................................................1
• Pan Head Screw (for installing the Divided Pickup) (M3x20) ..........2
• Spring (for installing the Divided Pickup)...........................................2
• Pan Head Screw with Spring Washer
(for installing the GK Connector) (M3x10) ...........................................2
Wirings
• For GK Connector-A (7 pins)..................................................................1
• For GK Connector-B (8 pins) ..................................................................1
• For GK Volume (3 pins)........................................................................... 1
• For Switches (8 pins)................................................................................ 1
• For Guitar Signal (2 pins)........................................................................ 1
• For Guitar Battery (2 pins)...................................................................... 1
• GK Volume (50kΩ ±20% B Curve)........................... ..............................1
• LED (with wiring)................... .................................................................1
• DOWN/S1, UP/S2 Switch (Momentary, Normal Operation) ...............2
• GUITAR/MIX/GK Select Switch (DPDT, ON-OFF-ON).........................1
Parts should be arranged separately
• Screw (for installing the Connector Plate)............................................ 4
• Ground Wire.........................................2 (See “Wiring Diagrams” (*1))
USING THE UNIT SAFELY
Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
* Material damage refers to damage or
other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.
001
• Before using this unit, make sure to read the instruc­tions below, and the Instruction Manual.
..................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
..................................................................................................
003
• Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific
instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor
..................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..................................................................................................
011
• Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..................................................................................................
014
• Protect the unit from strong impact. (Do not drop it!)
..................................................................................................
The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.
The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power­cord plug must be unplugged from the outlet.
012d
• Immediately turn the power off, and request servicing by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, when:
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..................................................................................................
013
• In households with small children, an adult should provide supervision until the child is capable of
following all the rules essential for the safe operation of the unit.
..................................................................................................
022b
• If the guitar includes a battery, remove the battery from the guitar before attempting installation of this unit.
106
• Never climb on top of, nor place heavy objects on the unit.
..................................................................................................
118c
• Whenever you’ve removed any parts (screws, washers, springs, etc.) used in attaching compo-
nents, be sure to keep them out of the reach of small children in order to prevent them from being swallowed accidentally.
..................................................................................................
This product complies with the requirements of
For EU Countries
European Directive 89/336/EEC.
Copyright © 2004 ROLAND CORPORATION All rights reserved. No part of this publication
may be reproduced in any form without the writ­ten permission of ROLAND CORPORATION.
Loading...
+ 2 hidden pages