Roland Corporation FR-3, FR-3s, FR-3sb, FR-3b Addendum
Version 2
V-Accordion
r
1
Kindly take note of the following
The following information has been changed or added as a result of a system software update for all FR-3 models.
Please correct those items accordingly.
Page 35, “Musette Detune”
→
Please add at the end of the following sentence:
“One reed is tuned slightly above, the other slightly
below the correct pitch (and the third, if available, is
tuned “properly”).”
“Musette Detune” only affects registers that use the 8’
reed, that is, usually:
5, 6a, 6b, 7a, 7b for all Sets except “F Folk”
4, 5, 6a, 6b, 7a, 7b for the “F Folk” Set.
It can be set for each register (provided the 8’ reed is
used) of all Sets separately, allowing you to use up to
56 different “ det ” assignments. Switching “Musette
Detune” settings while playing is therefore a matter of
selecting other Sets and/or pressing one of the registers
mentioned above.
Note that you will need to use the WRITE function if
you wish to keep your various “ det ” assignments after
switching off the FR-3.
→
Please delete the last note: “This parameter is reset
when you select a different Set.”
Page 36, “Editing settings”
→
In the table, please delete the following: “SET ✕ ”:
This setting changes when you select another Set.
→
The setting range of “Free Bass Mode” is “1~5”
→
The setting range of “Bass & Chord Mode” is “1~6”
→
Please add the following at the bottom of the table:
The “
trm
”, “
fbm
” and “
bCm
” parameters are not reset
when you load the factory defaults.
Page 37, “Musette Detune”
→
Please change the following: “This parameter allows
you to choose the system used for detuning the 8’
reeds of registers [5] MASTER, [6] MUSETTE and
[7] VIOLIN. It only applies to the Treble section.” … to:
This parameter allows you to choose the system used
for detuning the 8’ reeds of registers
[5]
MASTER,
[6]
MUSETTE and
[7]
VIOLIN. It only applies to the Treble
section. (After selecting Set 5, “FR FOLK”, you can also
detune the
[4]
ORGAN register.)
Page 37, “Treble Mode (only on the FR-3sb and
FR-3b)”
→
Please add the following note at the end of this sec-
tion:
Note: This parameter is not reset when you load the factory
defaults (page 53).
Page 42, “Free Bass Mode”, Bass & Chord Mode”
→
Please add the following note at the end of these
sections:
Note: This parameter is not reset when you load the factory
defaults (page 53).
Page 47, “MIDI parameter list”
→
The default setting of the “Bellows Expression TX”
parameter should read “Off”.
Page 50, “Bellows Expression TX”
→
The default setting of the “Bellows Expression TX”
parameter should read “Off”.
Improved or changed functions
Version 2
Version 2
2
r
FR-3s/FR-3/FR-3sb/FR-3b V-Accordion
Page 52, “Archiving your settings via MIDI (Bulk
Dump)”
→
Please change the following sentence: “The “ dMP ”
parameter allows you to transmit the contents of the
global area (that contains the PARAM LIST and MIDI
LIST settings) to a second FR-3s/FR-3sb or FR-3/
FR-3b…” … to:
The “ dMP ” parameter allows you to transmit the contents of the global area (which contains the PARAM
LIST and MIDI LIST settings), the Musette Detune
assignments and the User Programs to a second FR-3s/
FR-3sb or FR-3/FR-3b…”
Page 53, “Restoring the factory defaults”
→
Please insert the following note:
Note: Be aware that restoring the factory settings will also erase
your own “Musette Detune” and User Program settings. Consider
archiving the FR-3/FR-3b’s and FR-3s/FR-3sb’s settings with the
“
dmp ” function before using the “ fty ” function.
Page 54, “General remarks about batteries”
→
Please insert the following note:
• If the battery cover is not closed properly, the FR-3’s
display will show the message “
CVr ” when you switch it
on. In that case, press the battery cover until it clicks
into place.
Page 57, “Specifications”, “Operation modes”
→
Please add the following entry at the end of this
section:
10 User Program memories
Saving your settings (User Program)
Your FR-3 contains 10 memories where you can store the settings listed below. Working with those memories has the
advantage that you can recall frequently used settings at the press of a button. The User Program settings also include
the “address” of the last Set you selected. The following settings are saved to the User Programs:
Saving the current settings
Here is how to save the current settings of the eligible
parameters (see above) to the desired User Program
memory.
(1) Select the Set whose number should be memo-
rized.
(2) Set everything the way you want it to be when you
recall the User Program you are about to save.
(3) Press the [ORCHESTRA] and [5] registers.
(4) Press and hold the [SET] register until the “ Up- ”
message starts flashing.
New functions
Set
Number (1~10)
Treble section
Register
Octave setting
Orchestra
section
Register
Octave setting
Bass section
Register
Chord section
Register
Orchestral Bass
On/Off
Register
Level
Orchestral
Chord
On/Off
Register
Level
Orchestral Free
Bass
On/Off
Register
Level
Free Bass
On/Off
Register
Level
BASS
ORCHESTRA
FREE
BS
CHORD/
TREBLE
UP-
Loading...