Roland Corporation AT-15 Owner's Manual
Owner’s Manual
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any
form without the written permission of ROLAND CORPORATION.
Before using this unit, carefully read the sections entitled:
“IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT
SAFELY” (p. 3, 4), and “IMPORTANT NOTES” (p. 5, 6). These
sections provide important information concerning the proper
operation of the unit. Additionally, in order to feel assured that
you have gained a good grasp of every feature provided by your
new unit, Owner’s manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient
reference.
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
For EU Countries
For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
AVIS
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Never use with a cart, stand, tripod, bracket,
or table except as specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
BROWN:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
NEUTRAL
LIVE
For the U.K.
2
USING THE UNIT SAFELY
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
008a
• The unit should be connected to a power supply
only of the type described in the operating instructions, or as marked on the rear side of unit.
..........................................................................................................
008e
• Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
..........................................................................................................
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..........................................................................................................
012a:
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
3
USING THE UNIT SAFELY
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
026
• Do not put anything that contains water (e.g.,
flower vases) on this unit. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray
cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
101a
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..........................................................................................................
102b
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103a:
• At regular intervals, you should unplug the power
plug and clean it by using a dry cloth to wipe all
dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug and
the power outlet can result in poor insulation and
lead to fire.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107b
• Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from,
an outlet or this unit.
..........................................................................................................
108d: Selection
• If you need to move the instrument, take note of
the precautions listed below. At least two persons
are required to safely lift and move the unit. It
should be handled carefully, all the while keeping
it level. Make sure to have a firm grip, to protect
yourself from injury and the instrument from
damage.
• Check to make sure the knob bolts securing the
unit to the stand have not become loose. Fasten
them again securely whenever you notice any
loosening.
• Disconnect the power cord.
• Disconnect all cords coming from external
devices.
• Raise the adjusters on the stand (p. 16).
• Remove the music stand.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (p. 16).
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
117: Selection
• When using the bench, please observe the
following points:
• Do not use the bench as a toy, or as a stepping
stool.
• Do not allow two or more persons to sit on the
bench.
• Do not sit on the bench if the bolts holding the
bench legs are loose. (If the bolts are loose,
immediately re-tighten them using the supplied
wrench.)
..........................................................................................................
118
• Should you remove knob bolts, make sure to put
them in a safe place out of children’s reach, so
there is no chance of them being swallowed
accidentally.
..........................................................................................................
4
Important Notes
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2,
3 and 4, please read and observe the following:
Power Supply
301
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a
power supply noise filter between this unit and the
electrical outlet.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
308
• Although the LCD and LEDs are switched off when the
POWER switch is switched off, this does not mean that the
unit has been completely disconnected from the source of
power. If you need to turn off the power completely, first
turn off the POWER switch, then unplug the power cord
from the power outlet. For this reason, the outlet into
which you choose to connect the power cord's plug
should be one that is within easy reach and readily
accessible.
354b
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Also, do not allow lighting devices that normally are used
while their light source is very close to the unit (such as a
piano light), or powerful spotlights to shine upon the
same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
356
• Do not allow rubber, vinyl, or similar materials to remain
on the unit for long periods of time. Such objects can
discolor or otherwise harmfully affect the finish.
358
• Do not allow objects to remain on top of the keyboard or
pedal board. This can be the cause of malfunction, such as
keys ceasing to produce sound.
359
• Do not paste stickers, decals, or the like to this instrument.
Peeling such matter off the instrument may damage the
exterior finish.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this
unit; or move it farther away from the source of
interference.
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or
initiating a call, or while conversing. Should you
experience such problems, you should relocate such
wireless devices so they are at a greater distance from this
unit, or switch them off.
353
• Observe the following when using the unit’s floppy disk
drive. For further details, refer to “Before Using Floppy
Disks” (p. 6).
• Do not place the unit near devices that produce a
strong magnetic field (e.g., loudspeakers).
• Install the unit on a solid, level surface.
• Do not move the unit or subject it to vibration while
the drive is operating.
Maintenance
401b
• To clean the unit, use a dry, soft cloth; or one that is
slightly dampened. Try to wipe the entire surface using an
equal amount of strength, moving the cloth along with the
grain of the wood. Rubbing too hard in the same area can
damage the finish.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
Additional Precautions
552
• Unfortunately, it may be impossible to restore the contents
of data that was stored on a floppy disk and internal
memory once it has been lost. Roland Corporation
assumes no liability concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
554
• Never strike or apply strong pressure to the display.
555
•A small amount of noise may be heard from the display
during normal operation.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
5
IMPORTANT NOTES
Rear side of the disk
Write
(can write new data onto disk)
Protect
(prevents writing to disk)
Write Protect Tab
557
•A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559b
• When you need to transport the unit, pack it in shockabsorbent material. Transporting the unit without doing
so can cause it to become scratched or damaged, and
could lead to malfunction.
560
• Do not apply undue force to the music stand while it is in
use.
562
• Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
Before Using Floppy Disks
Handling Floppy Disks
651
• Floppy disks contain a plastic disk with a thin coating of
magnetic storage medium. Microscopic precision is
required to enable storage of large amounts of data on
such a small surface area. To preserve their integrity,
please observe the following when handling floppy disks:
• Never touch the magnetic medium inside the disk.
• Do not use or store floppy disks in dirty or dusty areas.
• Do not subject floppy disks to temperature extremes
(e.g., direct sunlight in an enclosed vehicle). Recommended temperature range: 10 to 50° C (50 to 122° F).
• Do not expose floppy disks to strong magnetic fields,
such as those generated by loudspeakers.
652
• Floppy disks have a “write protect” tab which can protect
the disk from accidental erasure. It is recommended that
the tab be kept in the PROTECT position, and moved to
the WRITE position only when you wish to write new
data onto the disk.
Handling the Floppy Disk Drive
602
• Install the unit on a solid, level surface in an area free from
vibration.
603
• Avoid using the unit immediately after it has been moved
to a location with a level of humidity that is greatly
different than its former location. Rapid changes in the
environment can cause condensation to form inside the
drive, which will adversely affect the operation of the
drive and/or damage floppy disks. When the unit has
been moved, allow it to become accustomed to the new
environment (allow a few hours) before operating it.
604
• To insert a disk, push it gently but firmly into the drive—
it will click into place. To remove a disk, press the EJECT
button firmly. Do not use excessive force to remove a disk
which is lodged in the drive.
605a
• Never eject a disk while reading or writing is in progress,
since that can damage the magnetic surface of the disk,
rendering it unusable. (The disk drive’s indicator will
light up at full brightness when the drive is busy reading
or writing data. Ordinarily, the indicator will be less
brightly lighted, or be extinguished.)
606
• Remove any disk from the drive before powering up or
down.
607
• To prevent damage to the disk drive’s heads, always try to
hold the floppy disk in a level position (not tilted in any
direction) while inserting it into the drive. Push it in
firmly, but gently. Never use excessive force.
608
• To avoid the risk of malfunction and/or damage, insert
only floppy disks into the disk drive. Never insert any
other type of disk. Avoid getting paper clips, coins, or any
other foreign objects inside the drive.
653
• The identification label should be firmly affixed to the
disk. Should the label come loose while the disk is in the
drive, it may be difficult to remove the disk.
654
• Store all disks in a safe place to avoid damaging them, and
to protect them from dust, dirt, and other hazards. By
using a dirty or dust-ridden disk, you risk damaging the
disk, as well as causing the disk drive to malfunction.
203
* GS ( ) is a registered trademark of Roland
Corporation.
203
* XG lite ( ) is a registered trademark of Yamaha
Corporation.
220
* All product names mentioned in this document are
trademarks or registered trademarks of their respective
owners.
6
Main Features
We want to take a moment to thank you for your purchase of the Roland AT-15 “Atelier Series”
Organ.
The AT-15 is an electronic organ which provides a generous collection of rich organ sounds. In
addition, it is designed to be easy to learn and use. In order to enjoy reliable performance of your
new keyboard for many years to come, please take the time to read through this manual in its
entirety.
■
Basic Concepts of the ATELIER Series
❍
A Full Complement of Organ Sounds
A wide range of basic organ sounds, ranging from jazz organ and pipe organ to theatre organ, are
onboard so you are sure to enjoy having access to all the sounds you expect from an organ.
Panel Layout Based on a Tradition of Emphasis on Realtime
❍
Operation
Based on the idea that you should be able to sit down and begin playing immediately, the operation
buttons of the panel are arranged by function as dictated by classic organ traditions, ensuring easy
and intuitive operation. All models of the ATELIER series feature the same operability, allowing
you to start playing immediately even if you switch models.
High-quality Sounds that You Can Use without Editing
❍
In addition to a full range of organ sounds, high-quality sounds such as strings and brass are also
included onboard. You can simply select sounds and enjoy playing the organ no need to perform
complicated editing operations.
❍
Expansive Lower Keyboard with Damper Pedal for Piano-like
Expressiveness
Piano is indispensable to the performance of contemporary music. On the ATELIER series, the
lower keyboard features an expanded range that gives you the expressive power of a piano. The
keyboard also features half-damper pedal capability and initial touch sensitivity, both
indispensable for piano performance.
All models provide high-quality grand piano sounds.
Design Utilizes Your Existing Music Data
❍
The ATELIER series is designed so that even on new models, you will feel right at home and can
begin playing immediately. Data compatibility has also been carefully taken into account, and song
data or registration data from earlier models can be used without change.
Music Styles From Around the World
❍
Many of the best-loved musical styles from around the world (rhythm and automatic
accompaniment patterns) are built in, allowing you to enjoy an international range of
performances.
❍
Make Full Use of Music Files
Compatible with GM2, the world standard in SMF music files, and equipped with its own floppy
disk drive, the AT-15 brings you access to the wealth of SMF music files available on the market.
You can also mute parts, allowing you to practice the part for each hand separately, and enjoy
performing ensemble with the music files.
7
Main Features
■
Main Features
❍
Highly Realistic Rhythms and Automatic Accompaniment Functions
All rhythms use data from performances by professional drummers, featuring high-quality
patterns with all the grooves and subtle nuance of the real thing. In addition, you can use automatic
accompaniments that are perfectly matched to each rhythm to enjoy the feeling of playing with
your own band in the background.
Developed Active Expression Sounds
❍
For some of the sounds, moving the expression pedal will vary not only the volume but also the
tone, or add other sounds. From pianissimo to fortissimo, the tonal character of the sound itself will
change as you perform a crescendo, or strings may appear behind the piano, creating dynamic
changes in tonality.
Human Voices
❍
In addition to a full complement of organ tones, the AT-15 also features tones that express a wide
range of human vocal qualities, including “Jazz Scat,” which changes according to how firmly the
keys are pressed, and “Classical” tones that perfectly express that choir image.
❍
Split Function
The 61-key lower manual can be split into separate sections, with each being used to play a
different tone. Using the Split function lets you perform with the richness of performance
expression rivalling that of three-manual and even four-manual instruments.
Registration Buttons
❍
The AT-15 features eight highly visible and intuitive buttons for calling up registrations, which
allow you to switch among tone and rhythm settings instantly. Furthermore, these are located
between the upper and lower manuals for better access when performing in real time.
Harmony Intelligence
❍
The Harmony Intelligence function automatically adds harmony to the upper keyboard sound
according to the chord you play in the lower keyboard. This gives you greater tonal depth and a
more powerful performance.
❍
High-Quality Reverb
In addition to often-used “HALL” and “ROOM” type reverbs, the AT-15 also includes “LARGE
CHURCH” and “CATHEDRAL” reverb settings, which feature extremely long reverberation
times and can be used to add enormous presence to your organ performances.
■
Conventions Used in This Manual
8
• Button names are enclosed in square brackets (“[ ]”), as in [Harmony Intelligence] button.
• [+] [-], [ ▲ ] [ ▼ ], [ ] [ ] means that you should press one or the other button.
Example: Value [-][+] buttons, Reverb [ ▲ ][ ▼ ] buttons, Tempo [ ][ ] buttons
Contents
USING THE UNIT SAFELY ...............................................................................................................3
Important Notes ...............................................................................................................................5
Main Features ............................................................................. 7
Panel Descriptions ..................................................................... 14
Before You Start Playing ........................................................... 16
Setting Up the Music Stand ..........................................................................................................................16
Connecting the Power Cord .........................................................................................................................16
Turning the Power On and Off ....................................................................................................................16
Tuning On the Power ........................................................................................................................16
Turning Off the Power ......................................................................................................................16
Using Headphones .........................................................................................................................................17
Restoring All the Factory Default Settings .................................................................................................17
Restoring All Settings Other Than the Rhythm [Disk] Button to Their Original Factory Condition . 18
Adjusting the Contrast of the Screen ...........................................................................................................18
Displaying Basic Screens ...............................................................................................................................18
Rhythm Screen ...................................................................................................................................18
Composer Screen ...............................................................................................................................18
Selecting and Playing Sounds .................................................... 19
Listening to the Demo Songs........................................................................................................................ 19
Selecting Voices .............................................................................................................................................. 21
About the Voices and Parts.............................................................................................................. 21
Functions of the Upper/Lower/Pedal Bass Sound Select Buttons............................................ 22
Selecting the Upper and Lower Voices .......................................................................................... 23
Selecting Pedal Bass Voice ............................................................................................................... 23
Selecting Solo Voice........................................................................................................................... 24
Selecting a Voice Using the [Others] Button.................................................................................. 25
Adjust the Volume Balance........................................................................................................................... 26
Transpose the Pitch in Octave Units (Octave Shift) .................................................................................. 27
Sustaining Notes Played on the Lower Keyboard .................................................................................... 28
Playing Drum Sound or Sound Effects on the Keyboard......................................................................... 28
Playing Drums from the Entire Lower Keyboard (Drums/SFX) ............................................... 28
Changing the Drum/SFX Set........................................................................................................... 29
Using the Rhythm Performance .................................................. 30
Selecting a Rhythm ........................................................................................................................................ 30
Playing Rhythms (Starting and Stopping the Rhythm)............................................................................ 31
Starting the Rhythm Automatically When You Play the Lower Keyboard or Pedalboard
(Sync Start).......................................................................................................................................... 31
Starting at the Press of a Button ...................................................................................................... 31
Stopping the Rhythm ........................................................................................................................ 32
Playing Rhythm and Automatic Accompaniment.................................................................................... 32
Adding Variety to the Rhythm and Automatic Accompaniment........................................................... 33
Changing the Tempo ..................................................................................................................................... 33
A Simple Way to Make Automatic Accompaniment Settings (One Touch Program)......................... 34
Using a Rhythm from a Disk........................................................................................................................ 35
Inserting and Ejecting a Floppy Disk.............................................................................................. 35
Reviewing the Styles on a Music Style Disk.................................................................................. 35
9
Contents
Loading Disk Rhythms Into Internal Memory.............................................................................. 36
Copying a Rhythm Saved to the Rhythm [Disk] Button ............................................................. 38
Deleting a Rhythm Saved to the Rhythm [Disk] Button.............................................................. 39
Restoring the Rhythm Stored in the Rhythm [Disk] Button to the Factory Settings............... 40
Adding Various Effects to a Voice .............................................. 41
Adding Harmony to a Melody (Harmony Intelligence) .......................................................................... 41
Changing the Type of Harmony Intelligence ............................................................................................ 42
Adding Modulation to the Sound (Rotary Effect)..................................................................................... 43
Reverb Effect ................................................................................................................................................... 44
Sustain Effect................................................................................................................................................... 45
Using the Play Functions ............................................................ 46
Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] Button).................................... 46
Playing the Solo Voice on the Lower Keyboard (Solo [To Lower] Button) ........................................... 47
Transposing to a Different Key (Transpose Buttons)................................................................................ 48
Adjusting the Overall Volume Using an Expression Pedal..................................................................... 49
Adding Decay to the Sound (Damper Pedal) ............................................................................................ 49
Using the Foot Switch.................................................................................................................................... 50
Using the Registration Buttons ................................................... 51
Storing Registrations...................................................................................................................................... 51
Recalling a Registration................................................................................................................................. 52
How to Recall a Registration............................................................................................................ 52
Changing the Timing of Recalling Registrations .......................................................................... 52
Automatically Registering When You Switch Panel Settings ................................................................. 53
Assigning a Name to a Registration Set...................................................................................................... 53
Copying Only the Name of a Registration .................................................................................... 55
Saving Registration Sets to a Floppy Disk.................................................................................................. 56
Loading Previously Saved Registration Sets Into the AT-15 ................................................................... 58
Loading a Set of Registrations ......................................................................................................... 58
Loading an Individual Registration................................................................................................ 59
Deleting a Set of Registrations from a Floppy Disk .................................................................................. 60
Record and Playback Your Performance .................................... 61
Playing Back Performance Songs Stored on Floppy Disk........................................................................ 62
Silencing a Specific Track (Track Mute)...................................................................................................... 64
Recording a Performance.............................................................................................................................. 65
Playing Back a Performance Song ............................................................................................................... 67
Rerecording Performance Data Recorded on the AT-15 .......................................................................... 68
Erasing a Performance Song......................................................................................................................... 69
Formatting Disks............................................................................................................................................ 70
Changing the Name of a Performance Song (Rename)............................................................................ 72
Saving Performance Songs onto Floppy Disk............................................................................................ 73
Deleting Performance Songs Stored on Disk ............................................................................................. 75
Layering a New Recording onto SMF Music Files.................................................................................... 76
Re-recording a Performance Saved on Floppy Disk................................................................................. 77
Using Song with a Different Tempo Than That of the Performance Song ............................................ 77
10
Settings for the Composer .......................................................... 78
Changing the Key When Playing Back Songs ............................................................................................78
Changing the Metronome Setting ................................................................................................................78
Adjusting the Metronome Volume ..............................................................................................................79
Changing the Sound of the Metronome .....................................................................................................79
Setting the Beat ...............................................................................................................................................80
Silencing a Specific Track ..............................................................................................................................80
Muting Individual Channels of Performance Data ...................................................................................81
Re-recording the Pedalboard Performance ................................................................................................82
Changing the Function of the Expression Pedal ........................................................................................82
Function During Recording .............................................................................................................82
Function During Playback ................................................................................................................83
Switching the Display of Lyrics On or Off .................................................................................................83
Adjusting the Effects .................................................................. 84
Sustain Effect ...................................................................................................................................................84
Changing the Sustain Length .......................................................................................................................84
Changing the Reverb Type ...........................................................................................................................85
Changing the Wall Type ...............................................................................................................................85
Changing the Depth of the Reverb ..............................................................................................................86
Contents
Various Other Settings ............................................................... 87
Turning Initial Touch On/Off (Initial Touch) ............................................................................................87
Using the Foot Switch to Switch Registrations (Regist Shift) ..................................................................87
Changing the Function of the Foot Switch (Left Foot SW, Right Foot SW) ...........................................87
Turning Chord Intelligence On/Off (Chord Intelli) .................................................................................88
Using the Leading Bass Function (Leading Bass) ......................................................................................89
Changing How the Solo Voice Responds (Solo Mode) ............................................................................89
Layering the Solo Voice and Lower Voice (Solo To Lower Mode) .........................................................90
Changing the Solo Split Point (Solo Split Point) ........................................................................................90
Changing the Pedalboard Polyphony (Pedal Bass Mode) .......................................................................90
Preventing Rhythm Tempos from Switching Automatically (Auto Standard Tempo) .......................91
Playing a Count Sound When the Intro Ends (Intro Count Down) .......................................................91
Changing the Sound of the Count Down (Count Down Sound) ............................................................91
Registration Arranger Update (Arranger Settings Recall Timing) .........................................................92
Registration Transpose Update (Transpose Setting Recall Timing) .......................................................92
Adjust the Standard Pitch (Master Tune) ...................................................................................................93
Selecting the MIDI Transmit Channel (Tx MIDI Channel) ......................................................................93
MIDI IN Mode ................................................................................................................................................94
Specifying Transmission of PC Numbers (Send PC Switch) ................................................................... 94
Setting PC Numbers (PC Number) ..............................................................................................................95
Connecting with External Devices .............................................. 96
Names and Functions of Jacks and Connectors .........................................................................................96
Connecting Audio Equipment .....................................................................................................................96
Making the Connections ...................................................................................................................96
If You’re Using MIDI .....................................................................................................................................97
Connecting the AT-15 to a MIDI Instrument ................................................................................97
11
Contents
Appendices
Troubleshooting .............................................................................................................................................98
Display Messages .........................................................................................................................................100
Voice List .......................................................................................................................................................102
Drum Set List ................................................................................................................................................103
Rhythm List ...................................................................................................................................................105
Chord List ......................................................................................................................................................106
Settings That Are Stored After the Power Is Turned Off .......................................................................108
Settings That Are Stored After the Power Is Turned Off ...........................................................108
Settings That Are Stored in the Registration Buttons .................................................................108
Settings That Are Stored in the Individual Registration Buttons .............................................108
Glossary .........................................................................................................................................................109
About ATELIER Series Sound Generator ....................................................................................110
MIDI Implementation Chart .......................................................................................................................111
Main Specifications ...................................................................................................................................... 112
Demo Song List .............................................................................................................................................114
Index ...............................................................................................................................................................116
12
MEMO
13
Panel Descriptions
Write
6
5
7
9
1 2 43
11
16 131217 10 1415
18
8
Pedal Bass Voice select buttons
1
( → p. 22, p. 23)
Pedal Part
[Alternate] button
[To Lower] button ( → p. 46)
Level [▲] [▼] button ( → p. 26)
Lower Voice select buttons ( → p. 23)
2
Lower part
Level [▲] [▼] button ( → p. 26)
3
Upper voice select buttons ( → p. 23)
Upper Organ part
Upper Orchestral part
Level [▲] [▼] button ( → p. 26)
Solo voice select buttons ( → p. 24)
4
Solo part
[Alternate] button
[To Lower] button ( → p. 47)
Level [▲] [▼] button ( → p. 26)
[Power On] switch ( → p. 16)
5
[Master Volume] knob ( → p. 16)
6
Part Balance [▲] [▼] button ( → p. 26, p. 44)
7
Lower [Drums/SFX] button ( → p. 28)
8
Transpose [-] [+] buttons ( → p. 48)
9
10
[Utility] button ( → p. 87)
[Display/Exit] button ( → p. 18)
Menu [ ][ ] buttons
Value [-] [+] buttons
Display ( → p. 18)
11
Beat Indicator ( → p. 33)
12
[Harmony Intelligence] button ( → p. 41)
13
[One Touch Program] button ( → p. 34)
14
Composer
15
Select [-] [+] buttons
[Load] button ( → p. 58, p. 59, p. 76, p. 77)
[Save] button ( → p. 56, p. 73)
[Registration] button ( → p. 53-p. 60)
Track Mute buttons ( → p. 64)
[Reset] button
[Play/Stop] button ( → p. 62, p. 67)
[Rec] button ( → p. 65, p. 68, p. 76, p. 77)
14
Rhythm select buttons ( → p. 30)
Manual
1 2 3 4 5 6 7 8
19
16
Tempo [ ][ ] button ( → p. 33)
Fill In button ( → p. 33)
[Intro/Ending] button ( → p. 31)
[Start/Stop] button ( → p. 31)
Rotary Sound [Fast/Slow] button ( → p. 43)
17
Disk Drive ( → p. 35)
18
Registration buttons
19
[Write] button ( → p. 51)
[Manual] button ( → p. 53)
Registration [1]–[8] buttons ( → p. 51)
15
Before You Start Playing
Setting Up the Music Stand
fig.01-03
1.
Attach the music stand by inserting it into the
two holes.
Connecting the Power Cord
1.
First, make sure that the [Power On] switch at
the panel’s left side is OFF (not pushed in).
2.
Connect the supplied power cord to the AC Inlet
connector, then plug the other end into an AC
outlet.
fig.01-04
fig.01-05
Master Volume
MaxMin
2.
Press the [Power On] switch to turn on the
power.
The power will turn on, and the Basic Screen appears on
the display.
fig.01-06
Lower position
ON
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
* Only use the power cord supplied with this instrument.
* Whenever you do not intend to use the instrument for extended
periods of time, pull out the power cord from the AC outlet.
Turning the Power On and Off
* Once the connections have been completed, turn on power to
your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction and/or
damage to speakers and other devices.
■
Tuning On the Power
1.
Make sure of the following before the power is
turned on.
•Is the power cord correctly connected to the AC inlet?
•Is the power cord correctly connected to the AC outlet?
•Is the [Master Volume] knob (located at the left of the
Lower keyboard) set to the Min (minimum) position?
3.
Turn the [Master Volume] knob or depress the
expression pedal to adjust the volume to a
suitable level.
Turning the [Master Volume] knob towards “Max”
increases the volume; turning the knob towards “Min”
decreases the volume. Likewise, pressing down on the
expression pedal increases the volume, while easing up
on the pedal decreases the volume.
fig.01-07
decrease
the volume
increase
the volume
■
Turning Off the Power
1.
Before switching the power off, set the [Master
Volume] knob to the Min (minimum) position.
2.
Press the [Power On] switch to turn off the
power.
fig.01-06
Upper position
OFF
* If you need to turn off the power completely, first turn off the
POWER switch, then unplug the power cord from the power
outlet. Refer to “Power Supply” (p. 5).
16
Before You Start Playing
Phones
Contrast
LCD
Using Headphones
The AT-15 features a Phones jack. This allows you to play
without having to worry about bothering others around you,
even at night.
fig.01-08
1.
Connect the headphones to the Phones jack on
the bottom left of the unit.
The sound from the built-in speakers stops.
Now, sound is heard only through the headphones.
Restoring All the Factory Default Settings
The settings stored in the AT-15 can be returned to their
factory settings. This function is called “Factory Reset.”
1.
Make sure there is no floppy disk in the disk
drive before carrying out the procedure.
2.
Turning off the power.
3.
While holding down the [One Touch Program]
button, press the [Power On] switch to turn the
power on.
fig.01-15
Do not turn off the power while the following screen is
displayed.
fig.01-16
2.
Adjust the headphones volume with the [Master
Volume] knob and Expression pedal.
* Accepts connection of Stereo headphones.
Some Notes on Using Headphones
• To prevent damage to the cord, handle the headphones
only by the headset or the plug.
• Headphones may be damaged if the volume is too high
when they are plugged in.
Lower the volume on the AT-15 before plugging in
headphones.
• To prevent possible auditory damage, loss of hearing, or
damage to the headphones, the headphones should not be
used at an excessively high volume.
Use the headphones at a moderate volume level.
When factory reset is completed, the basic screen
reappears.
* To return all settings other than the Rhythm [Disk] button
settings to their original factory conditions, refer to page 18.
* Loading factory default settings will erase any Registrations
currently in the memory of the AT-15. To save the registrations
you are currently using, refer to “Saving Registration Sets to a
Floppy Disk” (p. 56).
* To return only the Rhythm [Disk] button settings to their
original factory conditions, refer to page 40.
17
Before You Start Playing
Rhythm
Tempo
Chord
Restoring All Settings Other Than the Rhythm [Disk] Button to Their Original Factory Condition
All settings other than the Rhythm [Disk] button can be
returned to their factory settings. This function is called
“Panel Reset.”
1.
Make sure there is no floppy disk in the disk
drive before carrying out the procedure.
2.
Turning off the power.
3.
While holding down the [Harmony Intelligence]
button, press the [Power On] switch to turn the
power on.
fig.01-15
Do not turn off the power while the following screen is
displayed.
fig.01-16
Displaying Basic Screens
The instrument’s display provides a large variety of
information. The AT-15 has two types of basic display screen:
the Rhythm display, and the Composer display. You can
alternate from one to the other by pressing the [Display/Exit]
button.
fig.01-17
■
Rhythm Screen
fig.01-18
When panel reset is completed, the basic screen
reappears.
Adjusting the Contrast of the Screen
You can adjust the contrast of the screen.
1.
Turn the [LCD Contrast] knob located at the
bottom of the unit to adjust the contrast of the
screen.
LCD
Contrast
■
Composer Screen
When internal music data is selected:
fig.01-19
Song Name
Tempo Chord
When you have selected a performance song on a floppy
disk:
fig.01-20
Song Name
Tempo Chord
Measure Number
Song No.
18
Phones
Selecting and Playing Sounds
2, 3
4, 5
The data for the Demo song
that is being played is not
available at the MIDI Out
connector.
Listening to the Demo Songs
The AT-15 contains 12 Demo songs. Here’s how to play the Demo songs,
and fully appreciate the sounds, Rhythms, and Automatic Accompaniment
that are available with the AT-15.
fig.02-01
NOTE
All rights reserved.
Unauthorized use of this
material for purposes other
than private, personal
enjoyment is a violation of
applicable laws.
NOTE
1.
2.
Make sure that a floppy disk is not inserted in the disk drive.
If a floppy disk is in the disk drive, press the eject button (p. 35) and remove
the floppy disk.
Press the Select [-] [+] buttons simultaneously.
fig.02-02
3.
4.
5.
Press the Select [-] and [+] buttons to select a Demo song.
Press the [Play/Stop] button.
When the selected demo song ends, the next demo song will begin playing.
To stop playback in the middle of the song, press the [Play/
Stop] button.
Check out the “Demo Song
List” (p. 114) for
information such as the
names of the composers
and players of the demo
songs.
19
Selecting and Playing Sounds
❍
If the following screen appears
If the performance song in the unit has not been saved to a floppy disk, the
following message will appear, and it will not be possible to play the Demo
songs.
fig.02-03
If you don’t mind erasing this song, press the [Rec] button. However, if you
wish to save this song, press the [Reset] button to cancel the procedure, and
then save the song onto a floppy disk.
If you wish to save the
musical data to a floppy
disk, refer to “Saving
Performance Songs onto
Floppy Disk” (p. 73).
20
Selecting Voices
Upper Keyboard
Lower Keyboard
Pedalboard
The AT-15 is able to produce the sounds of various instruments. These
sounds are called “Voices” (or tones). It is very easy to select voices.
■
About the Voices and Parts
The AT-15 has two keyboards and one Pedalboard, as shown below.
From top to bottom these are called the “Upper Keyboard,” “Lower
Keyboard,” and “Pedalboard.”
fig.02-04
Selecting and Playing Sounds
The Upper Keyboard has two parts: “Organ,” “Orchestral.” You can select
one voice for each part, meaning that it is possible to layer the voices on
Upper Keyboard and play them simultaneously. The voice of the “Solo”
part can be layered on the Upper keyboard.
The Lower Keyboard has the part: “Lower.”
The Pedalboard has the part: “Pedal.”
Keyboard
Upper Keyboard
Lower Keyboard
Pedalboard Pedal Bass Pedal
Type of voices Parts
Upper
Solo Solo
Lower Lower
Solo
(This voice is sounded
only when Solo [To
Lower] button lights
up)
Upper Organ
Upper Orchestral
Solo
To play a Solo voice on the
Lower keyboard, select the
Solo voice and press the
Solo [To Lower] button (p.
47).
21
Selecting and Playing Sounds
■
Functions of the Upper/Lower/Pedal Bass Sound Select Buttons
fig.02-05
Each time you press a voice button, its indicator will switch between being
lit and being turned off. Voices that have their button indicator lit can be
played.
Two voices are assigned to both of the Pedal Part and Solo Part button
groups.
NOTE
If none of the voice buttons
are lit, playing the
keyboard will not produce
a sound.
The [Alternate] button switches between these two voices.
The [Alternate] button
The [Alternate] button is not lit.
The [Alternate] button is lit.
Voice that will be selected
The voice indicated on the button
is selected.
Another voice of the same family
or the voice indicated on the
bottom half of the button is
selected.
22
■
Selecting the Upper and Lower Voices
Select voices by pressing the Upper and Lower Part buttons.
When the power is turned on, the Upper keyboard will play “Full Organ 3”
and the Lower keyboard will play “Lower Organ2.”
Example: Selecting “Jazz Organ2” for the Upper Organ part,
and “Grand Piano” for the Upper Orchestral part.
Selecting and Playing Sounds
1.
2.
Press the Upper Organ [Jazz] button (indicator lights).
The name of the selected voice appears in the display for several seconds.
fig.02-06
Now when you play the Upper keyboard, the “Jazz Organ2” will sound.
Press the Upper Orchestral [Piano] button (the indicator
lights).
Now when you play the Upper keyboard, the two voices “Jazz Organ2” and
“Grand Piano” will sound simultaneously (mixed together).
■
Selecting Pedal Bass Voice
Immediately after the power is turned on, the Pedal Bass voice will sound
single notes using the “Organ Bass1” voice. Here’s how to select Pedal voice
played by the Pedalboard.
1.
Press the Pedal [Organ] button (indicator lights).
Settings can be adjusted to
allow multiple notes to be
played on the Pedalboard
(p. 90).
The name of the selected voice appears in the display for several seconds.
fig.02-08
Now when you play the Pedalboard, “Organ Bass1” will be heard.
Each time you press the [Alternate] button you will switch between the two
voices which are assigned the button.
NOTE
If you press the Pedal [To
Lower] button (indicator
lights p. 46), the Pedal Bass
voice can now be played by
the Lower keyboard, not by
the Pedalboard.
23
Selecting and Playing Sounds
It is possible to change how
a Solo voice will sound.
Normally, the Solo voice
will be sounded by the
highest note you play on
the Upper keyboard, but
you can make settings so
that the last-played note
will sound the Solo voice.
You can also make settings
so that the Solo voice will
be sounded by all notes of
the keyboard to which the
Solo voice is assigned. For
details refer to “Changing
How the Solo Voice
Responds (Solo Mode)” (p.
89).
■
Selecting Solo Voice
The Solo section of the Upper keyboard is monophonic, that is, the Solo
voice will only sound for the highest note played on the Upper keyboard.
This allows you to play full chords and have the selected Solo voice playing
the highest (solo) note.
fig.02-11
1
NOTE
If you press the Solo [To
Lower] button (indicator
lights p. 47), the Solo voice
can now be played by the
Lower keyboard, not by the
Upper Keyboard.
1.
Press the Solo [Trumpet] button (indicator lights).
The name of the selected voice appears in the display for a few seconds.
fig.02-12
Play the Upper keyboard. The selected voice will sound by the highest note
played.
Each time you press the [Alternate] button you will switch between the two
voices which are assigned the button.
24
■
You can jump by voice
group by pressing Menu
[] [ ] buttons to
select the voice group.
The sound number of each
voice is preceded by an
alphabetical character A–T
which indicates the sound
group; e.g., “G11 Strings1.”
You can also press the key
for the part containing a
changed voice to confirm
the voice setting.
About the voices that can
be assigned to an [Others]
button, please refer to
“Voice List” (p. 102).
Selecting a Voice Using the [Others] Button
Notice that there is an [Others] button for each part of the Upper, Lower,
Solo, Pedal. By using the [Others] button, you can select all the other voices,
the ones that can’t be selected directly by pressing voice buttons.
Selecting and Playing Sounds
1.
Press the [Others] button for the Part for which you wish to
specify a voice.
The voice name appears in the display.
fig.02-10 (P.29)
The indicator of the selected [Others] button will light.
For the solo part and pedal part, press the [Alternate] button and select the
voices to assign, either with the [Alternate] button ON (lit) or OFF (unlit).
2.
While the voice name is shown in the display screen, use the
Value [-] [+] buttons to select the desired voice.
The indicator of the selected [Others] button will blink.
To stop mid-way through this or any procedure, press the [Display/Exit]
button.
3.
Once again, press the [Others] button for the part whose
sound you wish to set to confirm the voice.
The indicator of the [Others] button will change from blinking to lit.
25
Selecting and Playing Sounds
Adjust the Volume Balance
The AT-15 allows you to adjust the volume balance individually for each
Part.
fig.02-13
The following buttons are used to adjust the volume of a multiple number
of Parts.
1.
Accomp/SMF [▼] [▲] button:
• Automatic Accompaniment (except bass part)
• Playback of performance data from something other than the Atelier
(EX.: SMF music files)
Rhythm [▼] [▲] button:
• Rhythm performance
• Drums/SFX
Pedal Level [▼] [▲] button:
• Pedal Voice
• Bass part of Automatic Accompaniment
The volume levels of each part are adjusted using the
corresponding [▲] and [▼] buttons.
When you press the up button (▲), the volume increases; when you press
the down button (▼), the volume decreases.
The volume can be set to any value from 0 to 12.
When you press the Level [▲] [▼] buttons, the volume for each part will be
shown in the display.
fig.02-14
NOTE
When the volume value
shown in the display is 0,
that part will produce no
sound.
26
Transpose the Pitch in Octave Units (Octave Shift)
The pitch of the sound played by the keyboard can be adjusted in one-octave
steps.
You can apply an Octave shift to the following 5 Parts:
The Upper Organ Part, Upper Orchestral Part
The Lower Part
The Pedal Part
The Solo Part
Selecting and Playing Sounds
1.
2.
3.
4.
5.
6.
Press the [Utility] button.
Press the Menu [ ] and [ ] button to select “Octave
Shift.”
f
Press the [Rec] button.
Use the Menu [ ] and [ ] button to select a performance
Part to which you wish to apply an Octave Shift.
Part: Pedal, Lower, U. Organ, U. Orch, Solo
fig.02-16
Use the Value [-] and [+] buttons to set the amount of shift.
The value can be set to a range of +/- 3 octaves.
Press the [Utility] button.
The basic screen reappears.
NOTE
Please note that when you
apply the Octave Shift
function to certain voices,
their pitch could be
stretched beyond their
recommended note ranges,
and they may not sound as
expected. Care should be
taken when using Octave
Shift.
27
Selecting and Playing Sounds
Sustaining Notes Played on the Lower Keyboard
You can have the sound for keys in the Lower keyboard continue to play,
even after you release the key, until the next key is pressed.
1.
Hold down the Pedal [To Lower] button for several seconds
until its indicator begins flashing.
The following appears in the screen.
The notes played on the lower keyboard will continue sounding.
2.
Press the Pedal [To Lower] button so its indicator goes out.
The sound stops playing.
Playing Drum Sound or Sound Effects on the Keyboard
■
Playing Drums from the Entire Lower Keyboard (Drums/SFX)
This setting is saved to the
registration.
1.
You can use the Lower keyboard to play various drum sounds (drum set).
In this case, the Lower voices will no longer sound.
fig.02-18
Press the [Drums/SFX] button (indicator lights).
Play the Lower keyboard and listen to the various drum sounds on each key.
The [Drums/SFX] button will alternate between on (lit) and off each time it
is pressed.
Immediately after the power is turned off, the STANDARD drum set will
sound.
Refer to “Drum Set List” (p.
103) for details on which
drum sound or Sound
Effect will be played by
each note.
NOTE
For some drum sets, there
will be keys that do not
sound.
28
■
Changing the Drum/SFX Set
Immediately after the power is turned on, the STANDARD drum set will
sound.
Selecting and Playing Sounds
1.
2.
Let’s try selecting a different Drum Set or the Sound Effect set.
As the drum set, you can choose from 8 types of drum set and one type of
sound effect. When you change the drum set, the sound produced by each
note will change.
fig.02-19
21, 3
Press the [Drums/SFX] button (indicator lights).
When the Drum Set name is displayed on the screen, press
Refer to “Drum Set List” (p.
103) for details on which
drum sound or Sound
Effect will be played by
each note.
3.
the Value [-] [+] buttons to select a Drum Set or Sound Effect
Set.
The [Drums/SFX] button indicator will begin to blink.
fig.02-20
You can select from 8 different Drum Sets and one set of Sound Effects as
follows:
STANDARD, ROOM, POWER, ELECTRONIC, TR-808, JAZZ, BRUSH,
ORCHESTRA, SOUND EFFECTS
To stop mid-way through this or any procedure, press the [Display/Exit]
button.
Press the [Drums/SFX] button once again.
The [Drums/SFX] button indicator will be lit constantly, and the selected
Drum/SFX set will be applied.
You can also play the lower
manual to confirm the
drum set.
29
Using the Rhythm Performance
The AT-15 lets you enjoy playing along with a rhythmic accompaniment.
Selecting a Rhythm
1.
The AT-15 provides 62 types of Rhythms and Automatic Accompaniments
(Music Styles). These are organized into eight groups.
fig.03-01
2
1, 3
Press a Rhythm button to select a Rhythm group.
The indicator of Rhythm button will light.
That Rhythm will be shown in the display.
fig.03-02
For more on the internal
rhythms, refer to the
“Rhythm List” (p. 105).
2.
Press the Value [-] and [+] buttons to select a different
Rhythm within the same group.
The indicator of the Rhythm button will blink.
3.
❍
Using the Rhythms of the [Disk] Button
Press the flashing rhythm button once more.
The Rhythm button’s indicator will change from blinking to light.
The Rhythm has now been applied.
The [Disk] button contains 4 preset Rhythms. These Rhythms can be
rewritten by loading disk styles into the AT-15.
The Rhythms that are already written in the [Disk] button memory can be
selected in the same way as when selecting Rhythms of another Rhythm
group.
If you wish to store a disk
style in the [Disk] button,
refer to “Loading Disk
Rhythms Into Internal
Memory” (p. 36).
30
Loading...