How it Works
Roland
Loading...
V-STUDIO 100
I/O Expansion by using the OCTA-CAPTURE
14 pgs2.56 Mb0
User Manual
64 pgs3.73 Mb0
User Manual
128 pgs10.84 Mb0
User Manual [ja]
14 pgs2.48 Mb0
User Manual [ja]
68 pgs4.95 Mb0
User Manual [nl]
130 pgs6.36 Mb0

Roland V-STUDIO 100 I/O Expansion by using the OCTA-CAPTURE

Download
I/O Expansion by using the OCTA-CAPTURE with the VS-100/VS-700
Operating Requirements
You can use the OCTA-CAPTURE Version 1.5 together with the VS-100 or VS-700 to expand the I/O. In order to expand the I/O, you must update the drivers and system software.
VS-100:
System program version 1.50 or later
Windows driver Ver.2.0.1
Mac driver
VS-700:
System program version 1.30 or later
Windows driver Ver.2.0.1
Mac driver Ver.1.0
Operating Requirements
NOTE
• The DIGITAL input connector is used in order to synchronize the VS-100/VS-700 with the OCTA-CAPTURE. You’ll need to obtain a coaxial cable
separately.
• This setup cannot be used at 192 kHz or higher.
• An internal hard disk drive that’s 7200 rpm or faster is required.
• In order to use this setup at 96 kHz or higher, a separate SATA hard disk drive is required as the audio recording destination. (This setup will not work
with a USB hard disk.)
• Depending on the application you’re using, the operating requirements may exceed those listed above.
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trademark of Roland Corporation in the United States and/or other countries.
2
Updating the VS-100/VS-700
4. In the “MIDI Out Device” eld, choose “CONTROL (VS-100).”
Updating the VS-100
You’ll need to perform the following updates in order to use expanded I/O functionality.
• Update the driver
Windows driver Ver.2.0.1
Mac driver
• Update the system program to version 1.50 or later
Updating the Driver
First, you need to download the driver from the Roland website.
The downloaded VS-100 driver version 2.00 is in a zip format archive le. Right-click the le’s icon, choose “Extract All” from the menu that appears, and extract the le as directed by the on-screen instructions.
In order to update the driver, you’ll rst need to uninstall the old driver.
For details on the installation procedure, refer to the Readme.htm le created when you extract the archive. You must read the Readme.htm le before you install the driver.
5. Click the [Path] button (on a Mac, the [Select...] button),
6. Click the [Scan SMF] (not required on a Mac), and verify that
7. Click the [Send] button
(on a Mac, choose “CONTROL.”)
and in SMF Path (on a Mac, SMF Folder), specify the folder location that contains the update les (_00001.mid–_00008. mid, end.mid).
the update les (_00001.mid–_00008.mid, end.mid) are shown in the le list.
File transmission will begin.
Transmission status is shown on the screen.
USB updater 12345 (Status of transfer) USB Online V1.30/01CA
When the transmission of the program has nished, the process of writing the program into the VS-100 will begin.
NOTE
Do not power o the VS-100 until the update is complete, doing so may damage the unit.
Updating the System Program
Checking the version
Check the version of the VS-100’s system software. When you power up the VS-100, the version of the current system software is displayed in the lower right of the screen.
Version Description
V1.30 or earlier
V1.50 or later An update is not required.
An update is required. Perform the update as described below.
Updating
1. Switch on the VS-100’s power, and before the level meter screen appears, simultaneously press the compressor/equalizer setting button and the CH1 [COMP/EQ] button, and continue holding down these buttons until the following screen appears.
The current system software version will appear.
USB updater 0
V1.30/01CA (current version)
2. Use the USB cable to connect the VS-100 to your computer.
When the USB connection is detected, the following screen will appear.
USB updater 0 USB Online V1.30/01CA
A screen like the following will appear.
USB updater erase USB Online V1.20/01AF
USB updater write USB Online V1.20/01AF
When the program has been updated successfully, a screen like the following will appear.
USB updater Update Successfully Please Reboot V1.20/01AF -> V1.50/01D4
Verify that the updated version is displayed.
This completes the update procedure.
8. Turn the power of the VS-100 o, then on again.
Make sure that the system software version shown in the lower right of the screen is V1.50.
* If the update was unsuccessful, you can retry the process from step
1.
3. Double-click “UpdSMFJ” on your computer.
3
Updating the VS-100/VS-700
Updating the VS-700
You’ll need to perform the following updates in order to use expanded I/O functionality.
• Update the driver to version 2.0.1 or later. (Windows only)
• Update the system program to version 1.30 or later.
Updating the Driver
You must install both the VS-700 driver and the VS-700C driver.
* The VS-700C driver is required for updating the system program
of the VS-700C console, so you must be sure to update the VS-700 driver and the VS-700C driver before you update the system program.
* In order to update the driver for the VS-700C, you must set the
VS-700C to the standalone mode. For details, refer to p. 164 in the owner's manual for the VS-700.
The downloaded le is a zip format archive. Right-click the le icon, choose “Extract All” from the menu that appears, and extract the les as directed by the on-screen instructions.
In order to update the drivers, you’ll rst need to uninstall the old drivers.
For details on the installation procedure, refer to the Readme.htm le created when you extract the archive. You must read the Readme.htm le before you install the drivers.
Checking the version of the VS-700R I/O
1. Install VS-700R I/O Editor
* VS-700R I/O Editor is an application that allows you to use VS-700R
I/O with applications other than SONAR. In this case, we’ll use it to check the version.
Read the contents of Readme.htm, and install the software as directed.
* For details on using or uninstalling VS-700R I/O Editor, refer to
Readme.htm.
2. Switch on the VS-700R’s power.
3. Use a USB cable to connect the VS-700R to your computer.
4. Start up VS-700R I/O Editor on your computer.
5. From the “Help” menu, open “VS-700R I/O Version.” If you’re
using Mac OS, choose the “VS-700R I/O Editor” menu command “About VS-700R I/O.”
6. The “About VS-700R I/O” window will appear; check the following version numbers.
• CPU
• DSP
• FANTOM VS
7. Click [OK] to close the “About VS-700R I/O” window.
8. Close VS-700R I/O Editor .
Updating the System Program
Checking the version of the VS-700C console
Check the version of the VS-700C console, VS-700 I/O CPU, VS-700 I/O DSP, and VS-700 I/O FANTOM VS.
If the version number is 1.30 or later, the update is not required.
1. Switch o the VS-700C’s power.
2. On the rear panel, set switch #8 of the “SETTING” switches to
the “ON” position (upward); this selects Update mode.
Normal setting Update mode
3. Switch on the VS-700C’s power.
4. The version is shown in the LCD display.
5. Switch the power o, then return switch #8 of the “SETTING”
switches on the rear panel to the “OFF” position (downward).
4
Updating the VS-100/VS-700
Updating the VS-700C console
* In order to update the VS-700C console, the VS-700C driver must be
installed in your computer.
* The update cannot be performed if the VS-700R is connected via
USB to your computer. Leave it disconnected.
1. Disconnect all USB cables from your computer (except those connecting the keyboard and mouse).
2. As described in “Checking the version of the VS-700C console,” put the VS-700C console in Update mode.
3. Use a USB cable to connect the VS-700C to your computer.
4. In the right side of the top panel, press the blinking [OK/
ENTER] button.
The indication in the LCD will change to “Erase.”
5. Press [OK/ENTER] once again.
The indication in the LCD will change to “Sure?”
6. Press [OK/ENTER] once again.
The indication in the LCD will change to “0%”.
7. On your computer, double-click “UpdSMFJ.”
8. As the “MIDI Out Device,” choose “CONSOLE (VS-700C)” (Mac
OS: “CONSOLE”).
9. Click the [Path] button (for Mac OS: the [Select...] button), and in the SMF Path (Mac OS: SMF Folder), specify the location that contains the update les (P00001.mid, P00002. mid).
10. Click the [Scan SMF] button (not necessary on Mac OS), and verify that the le list shows the update les (P00001.mid, P00002.mid).
11. Click the [Send] button.
Data transmission will begin.
The indication in the LCD will change to “End.”
* The update will require approximately one minute.
* Never turn o the power while the update is in progress.
12. In UpdSMFJ’s Send SMF/Complete dialog box, click [OK].
13. In UpdSMFJ, click [Exit] (for Mac OS: [QUIT]) to close
UpdSMFJ.
14. Turn o the power, wait one or two seconds, and then turn the power on again.
Verify that the version is shown as Version: 1.30.
15. Turn o the power, then return switch #8 of the “SETTING” switches on the rear panel to the “OFF” position (downward).
Updating the VS-700R I/O CPU and DSP
* You can update the VS-700R I/O CPU and DSP simultaneously in a
single operation.
1. Disconnect all USB cables from your computer (except those connecting the keyboard and mouse).
2. Make sure that the VS-700R’s power is switched o.
3. Disconnect everything from the VS-700R except for the
power cord.
4. In the VS-700R’s top panel, remove the expansion board cover; then at the right side, turn SW1 “4” on, and turn the other switches o.
5. In the left side of the VS-700R’s front panel, set the “SAMPLE RATE” knob to “88.2 kHz.”
6. Switch on the VS-700R’s power.
7. Verify that the VS-700R’s front panel [USB], [CONSOLE], [MIDI
IN], and [MIDI OUT] indicators blink.
8. Return the VS-700R’s SW1 “4” to the “o” position.
9. Verify that the [USB] and [CONSOLE] indicators have gone
out, and that the [MIDI IN] and [MIDI OUT] indicators are lit.
10. Use a USB cable to connect the VS-700R to your computer.
11. Verify that the VS-700R’s [USB], [MIDI IN], and [MIDI OUT]
indicators are lit.
12. On your computer, double-click “UpdSMFJ.”
13. As the “MIDI Out Device,” choose “IO (VS-700)” (for Mac OS:
“VS-700 I/O”).
14. Click the [Path] button (for Mac OS, the [Select...] button), and in the SMF Path (for Mac OS: SMF Folder) eld, specify the location of the update les (_00001.mid, end.mid).
15. Click the [Scan SMF] button (not necessary on Mac OS), and verify that the update les (_00001.mid, end.mid) are shown in the le list.
16. Click the [Send] button.
Data transmission will begin, and the VS-700R’s [MIDI IN] indicator will blink.
When the VS-700R’s [MIDI IN] and [MIDI OUT] indicator are both blinking, the update is complete.
* The update will require approximately two minutes.
* Never turn o the power while the update is in progress.
17. In UpdSMFJ’s Send SMF/Complete dialog box, click [OK].
18. In UpdSMFJ, click [Exit] (for Mac OS: [QUIT]) to close
UpdSMFJ.
19. Switch o the VS-700R’s power.
20. Reattach the expansion cover. If necessary, return the
“SAMPLE RATE” knob to the appropriate setting for your system.
21. Switch on the VS-700R’s power once again.
22. Start up VS-700R I/O Editor and verify that the version is
1.30.
55
Updating the VS-100/VS-700
Updating the VS-700R I/O FANTOM VS
1. Disconnect all USB cables from your computer (except those connecting the keyboard and mouse).
2. Make sure that the VS-700R’s power is switched o.
3. Disconnect everything from the VS-700R except for the
power cord.
4. In the VS-700R’s top panel, remove the expansion cover; then at the right side, turn SW1 “4” on, and turn the other switches o.
5. In the left side of the VS-700R’s front panel, set the “SAMPLE RATE” knob to “192 kHz.”
6. Switch on the VS-700R’s power.
7. Verify that the VS-700R’s front panel [USB], [CONSOLE], [MIDI
IN], and [MIDI OUT] indicators blink.
8. Return the VS-700R’s SW1 “4” to the “o” position.
9. Verify that the indicators that were blinking in step 6 have
now gone out.
10. Use a USB cable to connect the VS-700R to your computer.
11. Verify that the VS-700R’s [USB] and [MIDI OUT] indicators are
both blinking.
12. On your computer, double-click “UpdSMFJ.”
13. As the “MIDI Out Device,” choose “FANTOM VS (VS-700)” (for
Mac OS: “FANTOM VS”).
14. Click the [Path] button (for Mac OS, the [Select...] button), and in the SMF Path (for Mac OS, the SMF Folder) indication, specify the location of the update le (FantomVSUpdate. mid).
15. Click the [Scan SMF] button (not necessary on Mac OS), and verify that the update le (FantomVSUpdate.mid) is shown in the le list.
16. Click the [Send] button.
Data transmission will begin, and the VS-700R’s [MIDI IN] indicator will blink.
When the VS-700R’s [MIDI IN] and [MIDI OUT] indicators are both blinking, the update is complete.
* The update will require approximately three minutes.
* Never turn o the power while the update is in progress.
17. In UpdSMFJ’s Send SMF/Complete dialog box, click [OK].
18. In UpdSMFJ, click [Exit] (for Mac OS: [QUIT]) to close
UpdSMFJ.
19. Switch o the VS-700R’s power.
20. Reattach the expansion board cover. If necessary, return the
“SAMPLE RATE” knob to the appropriate setting for your system.
21. Switch on the VS-700R’s power once again.
22. Start up VS-700R I/O Editor and verify that the version is
1.30.
6
Connecting the VS-100/VS-700 and the OCTA-CAPTURE
Connecting the VS-100 and the OCTA-CAPTURE
You’ll be able to use the OCTA-CAPTURE and VS-100 as a 18-in/16-out (of these, 2 IN/2 OUT are used for synchronization) audio interface with ASIO on Windows or with Core Audio on Mac OS X. In order to connect two the VS-100 and OCTA-CAPTURE, you must turn on the VS EXPAND setting of the OCTA-CAPTURE, and set both units to digitally synchronize at the same sampling frequency. Before you start making settings, disconnect both units from the computer and turn o their power.
7
8
7
VS-100 OCTA-CAPTURE EXP
61
6
2
DIGITAL: AUTO SAMPLE FREQ: Same settings as the OCTA-CAPTURE
COAXIAL IN (7/8) COAXIAL CABLE
9
VS EXPAND: ON
COAXIAL OUT (9/10)
34 5
Connecting the VS-700 and the OCTA-CAPTURE
You’ll be able to use the OCTA-CAPTURE and VS-700 as a 29-in/34-out (of these, 2 IN/2 OUT are used for synchronization) audio interface with ASIO on Windows or with Core Audio on Mac OS X. In order to connect two the VS-700 and OCTA-CAPTURE, you must turn on the VS EXPAND setting of the OCTA-CAPTURE, and set both units to digitally synchronize at the same sampling frequency. Before you start making settings, disconnect both units from the computer and turn o their power.
7
8
7
9
VS-700R front
VS EXPAND: OFF DIGITAL: AUTO SAMPLE FREQ: Same settings as the OCTA-CAPTURE
VS-700R rearLower right of VS-700C front panel
6
COAXIAL IN (9/10) COAXIAL CABLE
OCTA-CAPTURE EXP
6
COAXIAL OUT (9/10)
12
VS EXPAND: ON DIGITAL: AUTO
34 5
7
Connecting the VS-100/VS-700 and the OCTA-CAPTURE
1. Switch on the power to the VS-100/VS-700.
The OCTA-CAPTURE unit will be the timing master.
2. Specify the sampling frequency (VS-100 Owner’s manual p. 52, VS-700 Owner’s manual p. 80)
* When using two units, they cannot be used with the 192 kHz setting.
3. Switch on the power to the OCTA-CAPTURE.
4. In the Utility section on the OCTA-CAPTURE, turn VS-EXPAND
on (OCTA-CAPTURE Owner’s manual p. 61).
5. Set the OCTA-CAPTURE to the same sampling frequency as the VS-100/VS-700 (OCTA-CAPTURE Owner’s manual p. 69).
6. In order to digitally synchronize the two units, use a coaxial cable to connect the OCTA-CAPTURE’s COAXIAL OUT (9/10) to the VS-100/VS-700’s COAXIAL IN.
* If the Utility section’s DIGITAL setting is turned o, the sampling
frequency will not switch. Change the VS-100’s DIGITAL setting to “AUTO” (VS-100 Owner’s manual p. 55)
7. Connect the VS-100/VS-700 and the OCTA-CAPTURE to the computer.
Connect the two USB cables to USB ports that are near each other.
Windows 7/Windows Vista users
The driver will be installed automatically when you connect the OCTA-CAPTURE. Please wait.
Windows XP users
After you’ve made the connection, follow steps 10 through 13 on p. 20 of the OCTA-CAPTURE Owner’s Manual to install the driver.
8. The procedure will dier depending on your system. Proceed as follows.
Windows users
If you’re using Windows, the two units must be connected to the same USB controller. In the Windows control panel, double-click the VS-100/VS-700 icon to open the VS-100/ VS-700 control panel driver settings. Make sure that “OK” was indicated for the VS EXPAND item.
If this does not indicate “OK,” proceed as directed below.
(A screen shot for the VS-100 is shown here.)
If “USB controller does not match” is shown:
Connect the VS-100/VS-700 or the OCTA-CAPTURE to a dierent USB port, and keep trying other USB ports until the indication is “OK” or “Sampling frequency does not match.”
* Alternatively, you can ensure that the VS-100/VS-700 and the OCTA-
CAPTURE are connected to the same USB controller by connecting them both to a USB 2.0 compliant hub.
If “Sampling frequency does not match” is shown:
Disconnect both USB cables from the computer, turn o the power of the rst unit, and start again from step 4. Connect each OCTA­CAPTURE unit to the same USB controller.
If VS EXPAND is grayed out:
Disconnect both USB cables from the computer, turn o the power of the VS-100/VS-700 and the OCTA-CAPTURE units, and start again from step 1.
Mac OS X users
Make “MIDI Input/Output Device Settings” (p. 25) on p. 25 of the OCTA-CAPTURE Owner’s Manual for the OCTA-CAPTURE . In step 5, enter the following names.
New Device Device Name
First [new external device] EXP MIDI
Second [new external device] EXP CTRL
Mac OS X 10.5.8 or earlier
1. After making connections, start up “Audio MIDI Setup” (/Applications/Utilities).
2. From the “Audio” menu, choose “Open Aggregate Device Editor.”
3. The device settings dialog box will appear. Click the [+] button to add an aggregate device.
Change the device set name to “VS-100 EXPANDED” or “VS-700 EXPANDED.”
4. Add a check mark to “VS-100”/ “VS-700”and then to “OCTA­CAPTURE EXP.”
5. In the clock eld, choose “OCTA-CAPTURE EXP.”
6. If a check mark has been placed in the Resample eld, clear the
check mark.
7. Click “Finish” to close the dialog box.
Mac OS X 10.6 or later
1. After making connections, start up “Audio MIDI Setup” (/Applications/Utilities).
2. Click the [+] button.
3. “Aggregate Device” will appear in the list; double-click it and
edit the name.
Change the device set name to “VS-100 EXPANDED” or “VS-700 EXPANDED.”
4. From the audio devices at the right, add a check mark to “Use” for “VS-100”, “VS-700”, and then for “OCTA-CAPTURE EXP.”
5. In the clock source eld, choose “OCTA-CAPTURE EXP.”
6. If a check mark has been placed in the Resample eld, clear the
check mark.
9. Connect your headphones to the PHONES jack of the VS-100 or the VS-700 unit.
For Mac OS X, refer to “Core Audio device ports and input channel numbers” (p. 13)
8
Settings for monitoring through headphones
1. Start up the OCTA-CAPTURE control panel.
2. In the lower left of the screen, click the [OCTA-CAPTURE EXP]
button.
The state of the OCTA-CAPTURE will be shown.
3. Choose [Open the Patch Bay] from the “Device” menu.
The patch bay screen will appear.
4. In the OUTPUT 9–10 eld, choose “DIRECT MIX A.”
5. Click the [Close] button to close the patch bay screen.
For the VS-100
You can use COAX (7/8) to control the volume. Set the volume at an appropriate level.
All signals being input to the OCTA-CAPTURE will be output from the PHONES jack of the VS-100/VS-700.
Connecting the VS-100/VS-700 and the OCTA-CAPTURE
Setting the sampling frequency
1. Disconnect the coaxial cable that connects the VS-100/ VS-700 and the OCTA-CAPTURE units.
2. Disconnect the two USB cables from the computer.
3. Change the sampling frequency of the two units.
Set both units to the same sampling frequency.
4. In order to digitally synchronize the two units, use a coaxial cable to connect the OCTA-CAPTURE’s COAXIAL OUT jack to the VS-100/VS-700’s COAXIAL IN jack.
5. Connect each unit’s USB cable to the computer.
* You’ll need to turn the VS-700’s power on once again.
For the VS-700
Using VS-700 I/O Editor or the VS-700 Control Surface plug-in, set DIGITAL1 INPUT SOURCE to COAXIAL IN, and set SYNC SOURCE to DIGITAL1. For details, refer to the online manual.
99
Appendix
Input/Output Devices
VS-100 + OCTA-CAPTURE
VS-100
Input Device Output Device
IN 1-2
IN 3-4 OUT 3-4
VS-100
DIGITAL
OCTA-CAPTURE
Input Device Output Device
OCTA-CAPTURE EXP
IN 5-6 OUT 5-6
IN 7-8 –
MAIN – –
IN 1-2
IN 3-4 OUT 3-4
IN 5-6 OUT 5-6
IN 7-8 OUT 7-8
IN 9-10 OUT 9-10
MAIN – –
OUT 1-2
VS-100
Used when synchronizing.
OUT 1-2
OCTA-CAPTURE EXP
VS-700 + OCTA-CAPTURE
VS-700
Input Device Output Device
FANTOM VS (VS-700)
ARX (VS-700) SUB ( VS-700)
AUX (VS-700) 1-2 (VS-700)
1-2 (VS-700) 3-4 (VS-700)
3-4 (VS-700) 5-6 (VS-700)
VS-700
OCTA-CAPTURE
Input Device Output Device
OCTA-CAPTURE EXP
5-6 (VS-700) 7-8 (VS-700)
7-8 (VS-700) 9-10 (VS-700)
DIGITAL1 (VS-700) DIGITAL1 (VS-700)
DIGITAL2 1-2 (VS-700) DIGITAL2 1-2 (VS-700)
DIGITAL2 3-4 (VS-700) DIGITAL2 3-4 (VS-700)
DIGITAL2 5-6 (VS-700) DIGITAL2 5-6 (VS-700)
DIGITAL2 7-8 (VS-700) DIGITAL2 7-8 (VS-700)
IN 1-2
IN 3-4 OUT 3-4
IN 5-6 OUT 5-6
IN 7-8 OUT 7-8
IN 9-10 OUT 9-10
MAIN – –
MAIN (VS-700)
VS-700
Used when synchronizing.
OUT 1-2
OCTA-CAPTURE EXP
10
Port Names for the VS-100 and OCTA-CAPTURE (VS EXPAND)
ASIO input port names
Device Input Output
IN 1-2 OUT 1-2
IN 3-4 OUT 3-4
VS-100
OCTA-CAPTURE (VS Expand: ON)
Core Audio device ports and input channel numbers
Device Port Core Audio channel number
VS-100
OCTA-CAPTURE (VS Expand: ON)
IN 5-6 OUT 5-6
DIGITAL –
MAIN –
EXP IN 1-2 EXP OUT 1-2
EXP IN 3-4 EXP OUT 3-4
EXP IN 5-6 EXP OUT 5-6
EXP IN 7-8 EXP OUT 7-8
EXP IN 9-10 EXP OUT 9-10
EXP MAIN –
IN 1-2 1, 2
IN 3-4 3, 4
IN 5-6 5, 6
DIGITAL 7, 8
MAIN 9, 10
IN 1-2 11, 12
IN 3-4 13, 14
IN 5-6 15, 16
IN 7-8 17, 18
IN 9-10 19, 20
MAIN 21, 22
Appendix
Core Audio device ports and output channel numbers
Device Port Core Audio channel number
OUT 1-2 1, 2
VS-100
OCTA-CAPTURE (VS Expand: ON)
OUT 3-4 3, 4
OUT 5-6 5, 6
OUT 1-2 11, 12
OUT 3-4 13, 14
OUT 5-6 15, 16
OUT 7-8 17, 18
OUT 9-10 19, 20
1111
Appendix
Port Names for the VS-700 and OCTA-CAPTURE (VS EXPAND)
ASIO input port names
Device Port 44.1/48 kHz 96 kHz
FANTOM VS √ √
ARX √ √
AUX √ √
IN 1-2 √ √
IN 3-4 √ √
VS-700
OCTA-CAPTURE (VS Expand: ON)
IN 5-6 √ √
IN 7-8 √ √
DIGITAL1 √ √
DIGITAL2 1-2 √ √
DIGITAL2 3-4 √ √
DIGITAL2 5-6 √ –
DIGITAL2 7-8 √ –
EXP IN 1-2 √
EXP IN 3-4 √
EXP IN 5-6 √
EXP IN 7-8 √
EXP IN 9-10 √
EXP MAIN √
ASIO output port names
Device Port 44.1/48 kHz 96 kHz
MAIN √ √
SUB √ √
OUT 1-2 √ √
OUT 3-4 √ √
OUT 5-6 √ √
VS-700
OCTA-CAPTURE (VS Expand: ON)
OUT 7-8 √ √
OUT 9-10 √ √
DIGITAL1 √ √
DIGITAL2 1-2 √ √
DIGITAL2 3-4 √ √
DIGITAL2 5-6 √ -
DIGITAL2 7-8 √ -
EXP OUT 1-2 √
EXP OUT 3-4 √
EXP OUT 5-6 √
EXP OUT 7-8 √
EXP OUT 9-10 √
12
Core Audio device ports and input channel numbers
Appendix
Device Port
FANTOM VS 1, 2 1, 2
ARX 3, 4 3, 4
AUX 5, 6 5, 6
IN 1-2 7, 8 7, 8
IN 3-4 9, 10 9, 10
VS-700
OCTA-CAPTURE (VS Expand: ON)
IN 5-6 11, 12 11, 12
IN 7-8 13, 14 13, 14
DIGITAL1 15, 16 15, 16
DIGITAL2 1-2 17, 18 17, 18
DIGITAL2 3-4 19, 20 19, 20
DIGITAL2 5-6 21, 22 –
DIGITAL2 7-8 23, 24 –
IN 1-2 25, 26 21, 22
IN 3-4 27, 28 23, 24
IN 5-6 29, 30 25, 26
IN 7-8 31, 32 27, 28
IN 9-10 33, 34 29, 30
MAIN 35, 36 31, 32
Core Audio channel number
44.1/48 kHz 96 kHz
Core Audio device ports and output channel numbers
Device Port
MAIN 1, 2 1, 2
SUB 3, 4 3, 4
OUT 1-2 5, 6 5, 6
OUT 3-4 7, 8 7, 8
OUT 5-6 9, 10 9, 10
VS-700
OCTA-CAPTURE (VS Expand: ON)
OUT 7-8 11, 12 11, 12
OUT 9-10 13, 14 13, 14
DIGITAL1 15, 16 15, 16
DIGITAL2 1-2 17, 18 17, 18
DIGITAL2 3-4 19, 20 19, 20
DIGITAL2 5-6 21, 22 –
DIGITAL2 7-8 23, 24 –
OUT 1-2 25, 26 21, 22
OUT 3-4 27, 28 23, 24
OUT 5-6 29, 30 25, 26
OUT 7-8 31, 32 27, 28
OUT 9-10 33, 34 29, 30
Core Audio channel number
44.1/48 kHz 96 kHz
1313
Appendix
Troubleshooting
Problem Cause
Can’t sync the VS-700 and the OCTA­CAPTURE.
Can’t monitor the OCTA-CAPTURE’s output through headphones.
When updating the VS-700’s system program, the input indicator blinked when you connected the USB cable to your computer, and the update could not be performed.
You performed the VS-700C console update as directed by the manual, but it was not successful.
Did you use VS-700 I/O Editor or the Control Surface plug-in to set DIGITAL 1 INPUT SOURCE to COAXIAL IN, and set SYNC to DIGITAL1? Have you connected the coaxial cable to the VS-700’s COAXIAL IN?
Did you make patchbay settings from the OCTA-CAPTURE’s control panel?
After powering up the VS-700, did you return the SW1 “4” switch to the “o” position?
Could a device other than the VS-700C be connected to the computer? If the VS-700R is connected to your computer when updating the VS-700C, updating the VS-700C will not be successful.
14
3PS
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use