Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (p. 2; p. 4). These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new
unit, this manual should be read in its entirety. The manual should be saved and kept on hand as a convenient
reference.
Thank you, and congratulations on your choice of the SRX-04
“Symphonique Strings” Wave Expansion Board.
The SRX-04 “Symphonique Strings” Wave Expansion Board
dedicates its entire memory to reproducing the most
expressive stereo-sampled string sounds on the planet.
Sampled with rich natural ambience, these string sounds can
be used across a complete spectrum of genres ranging from
classical to rock, pop, dance, film scoring and more.
Waveforms include full string sections as well as violin,
viola, cello, and contrabass sections. Each section contains
Waves representing different playing techniques and
rhythms, such as tremolo, pizzicato, marcato, spiccato, and
staccato—giving you lots of expressive possibilities.
The patches on the SRX-04 board are carefully selected and
optimized to bring out the expressiveness of the high-quality
waveforms. Moreover, settings for effects, sound parameters,
and controller assignments have been pre-programmed to
provide musicians with a rich tonal palette and unrivaled
realism.
• Patches:128
(The contents for the Fantom series/XV series/MX-200
and the RD-700/MC-909/VR-760 are slightly different.)
• Waveforms:196
* The parameter settings for patches are optimized for the
Fantom series, XV series, MX-200, RD-700, MC-909, and
VR-760 models, so there are some minor differences in the
sounds each instrument produces.
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
• Install the circuit board only into the specified unit
(Fantom series/XV series/MX-200/RD-700/MC909/VR-760). Remove only the specified screws
during the installation.
When you purchase the SRX-04 expansion board from an
authorized Roland dealer, the included sounds and samples
are licensed, not sold, to you by Roland Corporation, for
commercial use in music production, public performance,
broadcast, etc.
You may use any of the included phrases and/or samples in
a commercial or non-commercial recording without paying
any additional license fees. However, you must strictly
adhere to the following crediting guidelines on any music
recording that utilize material from SRX-04.
Reproduction or duplication of this collection or any of the
sound recording contained in the SRX-04, either as they exist
on this expansion board or by any means of reformatting,
mixing, filtering, re-synthesizing, processing or otherwise
editing for use in another product or for re-sale, is strictly
prohibited without the express written consent of Roland. All
unauthorized giving, trading, lending, renting, re-issue, redistribution or re-sale of the sounds included in the SRX-04
are expressly prohibited.
In Plain English: Be creative in your application of the SRX04 sounds, and keep this library for your use only. DO NOT
COPY IT.
Roland constantly monitors other Soundware releases to
check for copyright infringements, and will prosecute all
piracy and copyright violations to the fullest extent of the
law.
THIS LIBRARY IS GUARANTEED TO BE 100%
COPYRIGHT CLEAN.
291a
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2, please read and observe the
following:
901
To avoid the risk of damage to internal components that can
be caused by static electricity, please carefully observe the
following whenever you handle the board.
1
* Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
2
* When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
* Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
901 (F)
Veuillez suivre attentivement les instructions suivantes
quand vous manipulez la carte afin d’éviter tout risque
d’endommagement des pièces internes par l’électricité
statique.
1
* Toujours toucher un objet métallique relié à la terre (comme
un tuyau par exemple) avant de manipuler la carte pour vous
décharger de l’électricité statique que vous auriez pu
accumuler.
2
* Lorsque vous manipulez la carte, la tenir par les côtés. Évitez
de toucher aux composants ou aux connecteurs.
5
* Conservez le sachet d’origine dans lequel était la carte lors de
l’envoi et remettez la carte dedans si vous devez la ranger ou la
transporter.
Remove the cover located on the top (or rear) of your
instrument.
2.
Insert the Wave Expansion Board connector into a connector
for an SRX Series slot, while simultaneously inserting the
board holders into the holes in the Wave Expansion Board.
* Do not touch any of the printed circuit pathways or connection
terminals.
* Never use excessive force when installing a circuit board. If it doesn’t
fit properly on the first attempt, remove the board and try again.
3.
Use the supplied Installation Tool to turn the holders in the
LOCK direction, so the board will be fastened in place.
(To remove the Wave Expansion Board, turn the board holders
in the UNLOCK direction, and lift up the board.)
* When circuit board installation is complete, double-check your
work.
4.
Using the screws removed in Step 1, refasten the cover in its
original position.
5.
Check if the Wave Expansion Board is correctly installed.
* If the “EXP” display cannot be selected (doesn’t appear) in the
Waveform Selection Screen (refer to the owner’s manual of the
instrument you use), remove the Wave Expansion Board and
install it properly.
* Éteindre l'instrument.
1.
Retirer le couvercle situé sur le dessus (ou á l'arrière) de
l'instrument.
2.
Inserer le connecteur de la carte dans un des creneaux pour
la serie SRX tout en enfoncant les supports a carte dans les
trous de celle-ci.
* Ne pas toucher aux circuits imprimes ou aux connecteurs.
* Ne jamais forcer lors de l'installation de la carte de circuits
imprimes. Si la carte s'ajuste mal au premier essai, enlevez la
carte et recommencez l'installation.
3.
Utiliser l'outil d'installation fourni pour tourner les clips de
retenue vers la position de blocage (LOCK) de façon á ce que
la carte soit retenue en place.
(Pour retirer la carte d'expansion Wave, tourner les clips de
retenue de la carte vers la position déblocage (UNLOCK) et
retirer la carte en la soulevant.)
* Quand l'installation de la carte de circuits imprimes est terminee,
reverifiez si tout est bien installe.
4.
Remettre la plaque a sa place et la fixer a l'aide des vis
enlevees a l'etape 1.
5.
S'assurer que la carte d'expansion Wave est installée
correctement.
* S'il est impossible de sélectionner l'affichage “EXP” (il n'apparaît
pas) á l'écran de sélection Waveform (se reporter au guide du
propriétaire de l'instrument utilisé), retirer la carte d'expansion
Wave et la réinstaller correctement.
^:Accent
/sw:Alternate sound obtained with Key Velocity
/Mod: Alternate sound obtained with Modulation (CC:01)
/Aft:Alternate sound obtained with Aftertouch (CC:97)
When playing patches on the expansion board, we
recommend that you set all the EFFECTS ON/OFF settings
on the Fantom series/XV series to “ON.” If such settings are
set to “OFF,” you may not obtain the intended sound.
* Note that the Release Time has been set to a fairly long value
for some of the patches. As a result, if your sound generator
has been set so “Patch Remain” is “ON,” the release portion of
a previously sounding patch may continue to be heard even
after switching to a new patch.
* Refer to the owner’s manual for your instrument for specific
instructions on how to play Patches on the expansion board.
* On the Fantom series/XV series/MX-200, you can not select
only the patches which are designed to be used with the RD700/MC-909/VR-760.
97RhythmicPizz6STRINGS
98Harp StrPad 4COMBINATION
99Trem-Guitar 5AC.GUITAR
100 Baroque Ens27COMBINATION
101 ImitatEP Pad8OTHER SYNTH
102 Daybreak Ens6OTHER SYNTH
103 Grand Unison6ORCHESTRA
104 Va Sect&Glkn6ORCHESTRA
105 SRX Symphony8ORCHESTRA
106 XV Orchestra6ORCHESTRA
107 Full Orch 1 8ORCHESTRA
108 Orc with Str8ORCHESTRA
109 Symphnic Orc8ORCHESTRA
110 Strings&Hrns8ORCHESTRA
111 Strgs&Hrns 28ORCHESTRA
112 Octa StrEns 6BRIGHT PAD
113 Antique Str 4SOFT PAD
114 SweepSectStr6SOFT PAD
115 Stereo Tron!4STRINGS
116 Horror Str. 3STRINGS
117 DanzSurround4STRINGS
118 Ether Strngs4SOFT PAD
119 MoveFX Str 6SYNTH FX
120 Phase /Aft 4BRIGHT PAD
121 PhazeStrngs28BRIGHT PAD
122 Reverse Str23STRINGS
123 Haunted 8SYNTH FX
124 Rewind Vln 2BRIGHT PAD
125 Synthy Sweep2SYNTH FX
126 Ripple 3SYNTH FX
127 Mystery 2 7BRIGHT PAD
128 Rising STR 8SYNTH FX
^:Accent
/sw:Alternate sound obtained with Key Velocity
/Mod: Alternate sound obtained with Modulation (CC:01)
/Aft:Alternate sound obtained with Aftertouch (CC:97)
When playing patches on the expansion board, we
recommend that you set all the EFFECTS ON/OFF settings
on the Fantom series/XV series to “ON.” If such settings are
set to “OFF,” you may not obtain the intended sound.
* Note that the Release Time has been set to a fairly long value
for some of the patches. As a result, if your sound generator
has been set so “Patch Remain” is “ON,” the release portion of
a previously sounding patch may continue to be heard even
after switching to a new patch.
* Refer to the owner’s manual for your instrument for specific
instructions on how to play Patches on the expansion board.
* On the Fantom series/XV series/MX-200, you can not select
only the patches which are designed to be used with the RD700/MC-909/VR-760.
1F.Str mp A L*
2F.Str mp A R*
3F.Str mp B L*
4F.Str mp B R*
5F.Str mp C L*
6F.Str mp C R*
7F.Str mp + L*
8F.Str mp + R*
9Mrct A L *
10Mrct A R *
11Mrct B L *
12Mrct B R *
13Mrct C L *
14Mrct C R *
15Mrct + L *
16Mrct + R *
17Spcct A L *
18Spcct A R *
19Spcct B L *
20Spcct B R *
21Spcct C L *
22Spcct C R *
23Trem mp A L*
24Trem mp A R*
25Trem mp B L*
26Trem mp B R*
27Trem mp C L*
28Trem mp C R*
29Trem mp + L*
30Trem mp + R*
31Vn mp A L *
32Vn mp A R *
33Vn mp B L *
34Vn mp B R *
No. Name
35Vn mp C L *
36Vn mp C R *
37Vn mp + L *
38Vn mp + R *
39Va mp A L *
40Va mp A R *
41Va mp B L *
42Va mp B R *
43Va mp C L *
44Va mp C R *
45Va mp + L *
46Va mp + R *
47Vc mp A L *
48Vc mp A R *
49Vc mp B L *
50Vc mp B R *
51Vc mp C L *
52Vc mp C R *
53Vc mp + L *
54Vc mp + R *
55Cb mp A L *
56Cb mp A R *
57Cb mp B L *
58Cb mp B R *
59Cb mp C L *
60Cb mp C R *
61Cb mp + L *
62Cb mp + R *
63Vn mltV A L*
64Vn mltV A R*
65Vn mltV B L*
66Vn mltV B R*
67Vn mltV C L*
68Vn mltV C R*
No. Name
69Vn mltV + L*
70Vn mltV + R*
71Va mltV A L*
72Va mltV A R*
73Va mltV B L*
74Va mltV B R*
75Va mltV C L*
76Va mltV C R*
77Va mltV + L*
78Va mltV + R*
79Vc mltV A L*
80Vc mltV A R*
81Vc mltV B L*
82Vc mltV B R*
83Vc mltV C L*
84Vc mltV C R*
85Vc mltV + L*
86Vc mltV + R*
87Cb f A L *
88Cb f A R *
89Cb f B L *
90Cb f B R *
91Cb f C L *
92Cb f C R *
93Cb f + L *
94Cb f + R *
95Vn mltV^ A L*
96Vn mltV^ A R*
97Vn mltV^ B L*
98Vn mltV^ B R*
99Vn mltV^ C L*
100Vn mltV^ C R*
101Vn mltV^ + L*
102Vn mltV^ + R*
^: Accent
*:These are stereo waveforms, offered in left-right pairs.
When you create a Patch using the waveforms stored in the
Expansion Board, observe the following points:
* If you make a Patch with a single voice and then later play it in
a chord, the sound may be distorted with certain settings for
the Effects and TVA. If this happens, adjust the level of the
Effects and TVA.
103Va mltV^ A L*
104Va mltV^ A R*
105Va mltV^ B L*
106Va mltV^ B R*
107Va mltV^ C L*
108Va mltV^ C R*
109Va mltV^ + L*
110Va mltV^ + R*
111Vc mltV^ A L*
112Vc mltV^ A R*
113Vc mltV^ B L*
114Vc mltV^ B R*
115Vc mltV^ C L*
116Vc mltV^ C R*
117Vc mltV^ + L*
118Vc mltV^ + R*
119Vn Stc A L *
120Vn Stc A R *
121Vn Stc B L *
122Vn Stc B R *
123Vn Stc C L *
124Vn Stc C R *
125Va Stc A L *
126Va Stc A R *
127Va Stc B L *
128Va Stc B R *
129Va Stc C L *
130Va Stc C R *
131Vc Stc A L *
132Vc Stc A R *
133Vc Stc B L *
134Vc Stc B R *
135Vc Stc C L *
136Vc Stc C R *
No. Name
137Cb Stc A L *
138Cb Stc A R *
139Cb Stc B L *
140Cb Stc B R *
141Cb Stc C L *
142Cb Stc C R *
143All Stc L *
144All Stc R *
145Vn Pz mf A L*
146Vn Pz mf A R*
147Vn Pz mf B L*
148Vn Pz mf B R*
149Vn Pz mf C L*
150Vn Pz mf C R*
151Va Pz mf A L*
152Va Pz mf A R*
153Va Pz mf B L*
154Va Pz mf B R*
155Va Pz mf C L*
156Va Pz mf C R*
157Vc Pz mf A L*
158Vc Pz mf A R*
159Vc Pz mf B L*
160Vc Pz mf B R*
161Vc Pz mf C L*
162Vc Pz mf C R*
163Cb Pz mf A L*
164Cb Pz mf A R*
165Cb Pz mf B L*
166Cb Pz mf B R*
167Cb Pz mf C L*
168Cb Pz mf C R*
169All Pz mf L*
170All Pz mf R*
No. Name
171Vn Pz ff A L*
172Vn Pz ff A R*
173Vn Pz ff B L*
174Vn Pz ff B R*
175Vn Pz ff C L*
176Vn Pz ff C R*
177Va Pz ff A L*
178Va Pz ff A R*
179Va Pz ff B L*
180Va Pz ff B R*
181Va Pz ff C L*
182Va Pz ff C R*
183Vc Pz ff A L*
184Vc Pz ff A R*
185Vc Pz ff B L*
186Vc Pz ff B R*
187Vc Pz ff C L*
188Vc Pz ff C R*
189Cb Pz ff A L*
190Cb Pz ff A R*
191Cb Pz ff B L*
192Cb Pz ff B R*
193Cb Pz ff C L*
194Cb Pz ff C R*
195All Pz ff L*
196All Pz ff R*
^: Accent
*:These are stereo waveforms, offered in left-right pairs.
When you create a Patch using the waveforms stored in the
Expansion Board, observe the following points:
* If you make a Patch with a single voice and then later play it in
a chord, the sound may be distorted with certain settings for
the Effects and TVA. If this happens, adjust the level of the
Effects and TVA.