Roland KC-60 User Manual

Page 1
Owner’s Manual
Thank you, and congratulations on your choice of the Roland Keyboard Amplifier KC-60. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
Before using this unit, carefully read the sections entitled
• IMPORTANT SAFETY INSTRUCTIONS (p. 2)
• USING THE UNIT SAFELY (p. 3–p. 4)
• IMPORTANT NOTES (p. 5).
• Using a Speaker Stand (p. 10)
This unit is equipped with a protection circuit. The protection circuit helps ensure safety by operating when excessive input continues for a long time while the device is at a location with a high ambient temperature. Sound drop-out may occur when the protection circuit is actuated during use. Please read through the documentation carefully to ensure correct use.

Features

• This monitor-speaker amplifier is designed to provide high-quality sound for a variety of sources, including digital keyboards and sound modules.
• The two-way monitor features a 25-cm (10-inch) speaker and tweeter, and delivers a full 40 watts of high-power output.
• The input section features a three-channel mixer. Channel 1 is provided with an XLR connector in addition to supporting mic input.
• Features a SUBWOOFER OUT jack, allowing connection of a subwoofer for playback of even more impressive bass.
• Provided with an RCA phono type AUX IN jack, making it easy to connect devices such as CD and MD players.
• Master section includes a handy two-band equalizer for adjusting sound quality.
• Provided with a convenient headphones jack for use of the monitor at night.
Copyright © 2002 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Never use with a cart, stand, tripod, bracket, or table except as specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
For the U.K.
WARNING: IMPORTANT:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
THIS APPARATUS MUST BE EARTHED THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
Page 3

USING THE UNIT SAFELY

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
* Material damage refers to damage or
other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.
001
• Before using this unit, make sure to read the instructions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifica­tions on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” sheet.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
008a
• The unit should be connected to a power supply only of the type described in the operating instruc­tions, or as marked on the unit.
..........................................................................................................
009
• Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards!
..........................................................................................................
The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power­cord plug must be unplugged from the outlet.
010
• This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.
..........................................................................................................
012a:
• Immediately turn the power off, remove the power cord from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when:
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
3
Page 4
013
• In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords—the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.
..........................................................................................................
026
• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
..........................................................................................................
101a
• The unit should be located so that its location or position does not interfere with its proper venti­lation.
..........................................................................................................
102a
• Always grasp only the plug on the power-supply cord when plugging into, or unplugging from an outlet.
..........................................................................................................
103a:
• Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire. Periodically wipe away such dust with a dry cloth. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time.
..........................................................................................................
104
• Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on the unit.
..........................................................................................................
107a
• Never handle the power cord or its plug with wet hands when plugging into, or unplugging from, an outlet.
..........................................................................................................
108a
• Before moving the unit, disconnect the power plug from the outlet, and pull out all cords from external devices.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and unplug the power cord from the outlet.
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning in your area, pull the plug on the power cord out of the outlet.
..........................................................................................................
4
Page 5

IMPORTANT NOTES

291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2, 3 and 4, please read and observe the following:
Power Supply
301
• Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or variable lighting system).
307
• Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.
308
• Although the LEDs are switched off when the POWER switch is switched off, this does not mean that the unit has been completely disconnected from the source of power. If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. For this reason, the outlet into which you choose to connect the power cord’s plug should be one that is within easy reach.
Placement
351
• Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference.
352a
• This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.
352b
• Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
354b
• Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Also, do not allow lighting devices that normally are used while their light source is very close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time. Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the temper­ature and/or humidity is very different, water droplets (conden­sation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
356
• Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or otherwise harmfully affect the finish.
357
• Do not put anything that contains water (e.g., flower vases) on the unit. Also, avoid the use of insecticides, perfumes, alcohol, nail polish, spray cans, etc., near the unit. Swiftly wipe away any liquid that spills on the unit using a dry, soft cloth.
359
•Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior finish.
• Do not allow objects to remain on top of the unit while it is in operation.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
• For routine care of the carpeted surfaces, use a brush with stiff bristles.
Additional Precautions
553
• Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the connector itself—never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements.
557
•A small amount of heat will radiate from the unit during normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.
562
• Use a cable from Roland to make the connection. If using some other make of connection cable, please note the following precau­tions.
• Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
• When transporting and storing the KC-60, be sure to secure the AC cord to the cord hook on the rear of the main unit.
5
Page 6

Panel Descriptions

Control Panel
fig.01
2781 543 6
Jack Panel
fig.01
1291011
CHANNEL CONTROL
1. CH 1 knob / CH 1 Input Jacks
In addition to a 1/4” phone jack, this channel is equipped with a balanced XLR connector, useful for connecting microphones. This accepts input levels ranging from mic input (-50 dBu) to line level from sound modules and other equipment (-20 dBu).
2. CH 2 and CH 3 knobs / CH 2 and CH 3 Input Jacks
Use these for connecting keyboards, sound modules, and other devices. They accept line level input (-20 dBu).
MASTER CONTROL
These adjust the tone and volume level for the built-in speakers or for headphones.
3. LOW Knob
5. VOLUME Knob
This adjusts the total volume level of the unit’s internal speaker. The SUBWOOFER OUT output is also changed. When connecting headphones, adjust the headphone volume level.
* The VOLUME knob do not affect the line outs.
6. PHONES Jack
This is for connecting headphones. The unit’s speakers are deactivated when headphones are plugged in. Also, no signals are output from SUBWOOFER OUT (p. 7).
* Always be sure to lower the VOLUME knob to 0 whenever
connecting and disconnecting headphones.
* Although the PHONES jack accepts stereo plugs, the audio
output is mono.
This adjusts the level of the bass range.
4. HIGH Knob
This adjusts the level of the treble range.
6
Page 7
7. Power Indicator
This indicator illuminates when the power is on.
8. POWER Switch
This switches the power on and off.
* Always be sure to lower the volume on the KC-60 and any
connected equipment to 0 whenever turning the power on or off.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will operate normally. Slight pop noise may come from the speakers when the power is switched on, but this does not indicate a problem.
Panel Descriptions
* Refer to p. 9 for the order in which to turn the power to
connected devices on and off.
9. AUX IN Jacks
These are RCA phono type input jacks. You use these to connect equipment such as CD and MD players, and have them sound along with the equipment connected to channel 1 through channel 3. They accept level input of -10 dBu.
* To adjust the volume level of equipment connected to the AUX
IN jacks, use the controls on such equipment.
* Even though the input signal may be in stereo, the signal is
mixed internally to a mono signal.
10.LINE OUT Jack
Connect mixers, recorders, and other such equipment here. This output jack provides +4 dBu line level output.
* The MASTER CONTROL knobs (the LOW, HIGH, and
VOLUME controls) do not affect the output from LINE OUT.
11.SUBWOOFER OUT Jack
This lets you play even more powerful bass by connecting a powered subwoofer. Provides full-range output, at an output level +4 dBu. You can use the MASTER CONTROL knobs (LOW, HIGH, and VOLUME) to adjust the tone and volume level of the signals output from SUBWOOFER OUT.
* No signals are output from SUBWOOFER OUT when
headphones are connected.
7
Page 8

Making the Connections

Refer to the figure shown below to connect the KC-60 and the other equipment.
fig.03
Rear PanelControl Panel
Stereo Headphone
INPUTINPUT
CD Player
Subwoofer
(With built-in amp)
Here is an example of a setup that makes full use of the KC­60’s mixer and monitor functions. A microphone is input to CH 1, which accepts mic level input. Connect a keyboard, recorder, or other sound­generating device to the CH 2 and CH 3 inputs.
* To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power on all devices before making any connections. Set all of the KC­60’s channel volume knobs as well as the VOLUME knob to zero.
Mixer
Microphone
OUTPUT OUTPUT
Drum Machine
* Howling could be produced depending on the location of
microphone relative to speakers. This can be remedied by:
1. Changing the orientation of the microphone.
2. Relocating microphone at a greater distance from the speaker.
3. Lowering volume levels.
* When connection cables with resistors are used, the volume level
of equipment connected to the inputs (CH 1 through CH 3 and AUX IN) may be low. If this happens, use connection cables that do not contain resistors, such as those from the Roland PCS series.
Keyboard
* The pin assignment for the XLR type connectors is as shown
below. Before making any connections, make sure that this pin assignment is compatible with that of all your other devices.
fig.04
8
Page 9
1.
2.
3.
2.
3.
4.
5.
6.
Making the Connections
1.

Switching the Power On and Off

Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
Make sure that all volume controls on the KC-60 and connected devices are set to 0.
Turn on all the devices connected to the KC-60’s input jacks (CH 1 through CH 3 and AUX IN).
Turn on the KC-60.
Switch on any equipment connected to the KC-60’s LINE OUT or SUBWOOFER OUT jacks.
Adjust the volume levels for the devices.
Before switching off the power, lower the volume on each of the devices in your system and then TURN OFF the devices in the reverse order to which they were switched on.

About the Volume-level Settings

In order to get optimum sound from the KC-60 when performing, set the volume as described below.
Operate the CH 1 through CH 3 volume knobs to adjust the volume level for channels 1 through 3.
fig.11
Adjust the volume balance for channels 1 through 3 at this time.
* To adjust the volume level of equipment connected to the AUX
IN jacks, use the controls on such equipment.
Adjust the LOW and HIGH knobs to obtain the tone you want.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will operate normally. For protection from sudden big sound, always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction.
Use the VOLUME knob to adjust the overall volume level.
fig.12
* If the sound is distorted, lower the CH 1 through CH 3 volume
knobs, VOLUME knob and/or the volume knobs for devices connected to the input jacks (CH 1 through CH 3 and AUX IN).
9
Page 10

Using a Speaker Stand

By using a speaker stand, you can mount the KC-60 at the optimal height for use as a monitor speaker or simple PA device.
fig. Caution
The KC-60 is designed to be used only with speaker stands whose dimensions meet the specifications described below. Do not use it with a speaker stand that does not meet the following specifications.
fig.05
Diameter: 3.8 cm
(1-1/2”)
Leg spread: 120 cm (47-1/4”) or more
fig.06_e
Diameter:
136 cm (53-9/16”)
or more
Before use, adjust the speaker stand to a height of 165 cm (65”) or less and a leg spread of 120 cm (47-1/4”) or more, as shown in the figure below.
fig.08\
165 cm (65”) or less
120 cm (47-1/4”) or more
Using a speaker stand that does not meet the specifications at left or that is adjusted to a height over 165 cm (65”), or a leg spread of less than 120 cm (47-1/4”) may result in damage to equipment or injury due to the stand tipping over.
Leg spread: 120 cm (47-1/4”) or more
When deciding on a stand to use with the KC-60, make sure to pick one that is capable of supporting its weight.
When using KC-60 with a speaker stand, the speaker stand must be carefully placed so it is level and sure to remain stable.
Cables connected to KC-60 should be given enough slack to prevent accidents that might result from someone tripping over them.
To prevent accidents due to falls, do not place any object on the KC-60 when it’s mounted on a speaker stand.
Always have at least one other person assist you when mounting the KC-60 on a speaker stand, or when adjusting the height of the stand while the KC-60 remains mounted on it.
10
Page 11

Appendices

Block Diagram

CH1
MIC/LINE
BALANCED
CH1
MIC/LINE
CH 2 LINE
CH 3 LINE
AUX IN
AUX IN
L
R
HOT
COLD
CH 1 VOL
CH 2 VOL
CH 3 VOL
LINE OUT

Main Specifications

SPEAKER
LOW
MASTER VOL
HIGH
POWER AMP
HIGH PASS FILTER
LINE OUT
SUBWOOFER OUT
PHONES
TWEETER
WOOFER
Rated Power Output
40 W
Nominal Input Level (1 kHz)
Input
Channel 1 (MIC/LINE): -50 – -20 dBu Channel 2, 3 (LINE): -20 dBu
AUX IN: -10 dBu
Nominal Output Level
LINE OUT: +4 dBu SUBWOOFER OUT: +4 dBu * 0 dBu = 0.775 Vrms
Speakers
25 cm (10 inches) x 1 Tweeter x 1
Controls
Channel 1 (MIC/LINE) Volume Knob Channel 2 (LINE) Volume Knob Channel 3 (LINE) Volume Knob Equalizer: LOW Knob, HIGH Knob VOLUME Knob POWER Switch
Indicator
POWER
Connectors
Channel 1 Input Jack (XLR type, 1/4” phone type) Channel 2 Input Jack (1/4” phone type) Channel 3 Input Jack (1/4” phone type) AUX IN Jack (RCA phono type) LINE OUT Jack (1/4” phone type) SUBWOOFER OUT Jack (1/4” phone type) PHONES Jack (1/4” TRS phone type, mono signal output)
Power Supply
AC 117 V, AC 230 V, AC 240 V
Power Consumption
45 W
Dimensions
420 (W) x 300 (D) x 410 (H) mm 16-9/16 (W) x 11-13/16 (D) x 16-3/16 (H) inches
Weight
12.5 kg 27 lbs 9 oz
Accessory
Owner’s Manual
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
11
Page 12
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.
AFRICA
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429
SOUTH AFRICA
That Other Music Shop (PTY) Ltd.
11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA
P.O.Box 32918, Braamfontein 2017 Johannesbourg, SOUTH AFRICA TEL: (011) 403 4105
Paul Bothner (PTY) Ltd.
17 Werdmuller Centre, Main Road, Claremont 7708 SOUTH AFRICA
P.O.BOX 23032, Claremont 7735, SOUTH AFRICA TEL: (021) 674 4030
ASIA
CHINA
Roland Shanghai Electronics Co.,Ltd.
5F. No.1500 Pingliang Road Shanghai, CHINA TEL: (021) 5580-0800
Roland Shanghai Electronics Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili Chaoyang District, Beijing, CHINA TEL: (010) 6426-5050
HONG KONG
Tom Lee Music Co., Ltd. Service Division
22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855
MALAYSIA
BENTLEY MUSIC SDN BHD
140 & 142, Jalan Bukit Bintang 55100 Kuala Lumpur,MALAYSIA TEL: (03) 2144-3333
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801
SINGAPORE
Swee Lee Company
150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676
CRISTOFORI MUSIC PTE LTD
Blk 3014, Bedok Industrial Park E, #02-2148, SINGAPORE 489980 TEL: 6243-9555
TAIWAN
ROLAND TAIWAN ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C. TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2, Bangkok 10100, THAILAND TEL: (02) 2248821
VIETNAM
Saigon Music
138 Tran Quang Khai St., District 1 Ho Chi Minh City VIETNAM TEL: (08) 844-4068
AUSTRALIA/ NEW ZEALAND
AUSTRALIA
Roland Corporation Australia Pty., Ltd.
38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA TEL: (02) 9982 8266
NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden, Auckland, NEW ZEALAND TEL: (09) 3098 715
CENTRAL/LATIN AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700
BRAZIL
Roland Brasil Ltda
Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666
COSTA RICA
JUAN Bansbach Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211
CHILE
Comercial Fancy S.A.
Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final Alameda Juan Pablo , Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101
PARAGUAY
Distribuidora De Instrumentos Musicales
J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (021) 492-124
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa 1771 C.P.: 11.800 Montevideo, URUGUAY TEL: (02) 924-2335
VENEZUELA
Musicland Digital C.A.
Av. Francisco de Miranda, Centro Parque de Cristal, Nivel C2 Local 20 Caracas VENEZUELA TEL: (212) 285-8586
EUROPE
AUSTRIA
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74, A-6063 RUM, AUSTRIA TEL: (0512) 26 44 260
BELGIUM/HOLLAND/ LUXEMBOURG
Roland Benelux N. V.
Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811
DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK, Parc de l'Esplanade, F 77 462 St. Thibault, Lagny Cedex FRANCE TEL: 01 600 73 500
FINLAND
Roland Scandinavia As, Filial Finland
Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020
GERMANY
Roland Elektronische Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090
GREECE
STOLLAS S.A. Music Sound Light
155, New National Road Patras 26442, GREECE TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011
IRELAND
Roland Ireland
Audio House, Belmont Court, Donnybrook, Dublin 4. Republic of IRELAND TEL: (01) 2603501
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300
NORWAY
Roland Scandinavia Avd. Kontor Norge
Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074
POLAND
P. P. H. Brzostowicz
UL. Gibraltarska 4. PL-03664 Warszawa POLAND TEL: (022) 679 44 19
PORTUGAL
Tecnologias Musica e Audio, Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto 4050-465 PORTO PORTUGAL TEL: (022) 608 00 60
ROMANIA
FBS LINES
Piata Libertatii 1, RO-4200 Gheorghehi TEL: (095) 169-5043
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l 107 564 Moscow, RUSSIA TEL: (095) 169 5043
SPAIN
Roland Electronics de España, S. A.
Calle Bolivia 239, 08020 Barcelona, SPAIN TEL: (93) 308 1000
SWEDEN
Roland Scandinavia A/S SWEDISH SALES OFFICE
Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383
UKRAINE
TIC-TAC
Mira Str. 19/108 P.O. Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701
MIDDLE EAST
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 211 005
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426
IRAN
MOCO, INC.
No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169
ISRAEL
Halilit P. Greenspoon & Sons Ltd.
8 Retzif Ha'aliya Hashnya St. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666
JORDAN
AMMAN Trading Agency
245 Prince Mohammad St., Amman 1118, JORDAN TEL: (06) 464-1200
KUWAIT
Easa Husain Al Yousifi Est.
Abdullah Salem Street, Safat, KUWAIT TEL: 243-6399
LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 16-5857 Beirut, LEBANON TEL: (01) 20-1441
QATAR
Al Emadi Co. (Badie Studio & Stores)
P.O. Box 62, Doha, QATAR TEL: 4423-554
SAUDI ARABIA
aDawliah Universal Electronics APL
Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081
SYRIA
Technical Light & Sound Center
Khaled Ebn Al Walid St. Bldg. No. 47, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384
TURKEY
Barkat muzik aletleri ithalat ve ihracat Ltd Sti
Siraselviler Caddesi Siraselviler Pasaji No:74/20 Taksim - Istanbul, TURKEY TEL: (0212) 2499324
U.A.E.
Zak Electronics & Musical Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715
NORTH AMERICA
CANADA
Roland Canada Music Ltd. (Head Office)
5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) 270 6626
Roland Canada Music Ltd. (Toronto Office)
170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938, U. S. A. TEL: (323) 890 3700
As of April 1, 2003 (Roland)
SD000223 1DH
Loading...