ROHS VCC Product Manual
Virtual Cash Controller
product guide
–
page
1
VCC
Copy & Print controller
PRODUCT GUIDE
Conforms to FCC CFR 47 part 15 and
European Community EMC Directive 89/336/EEC
RoHS compliant under
EU Directive 2002/95
Virtu
al Cash Controller
product guide
–
page
2
Contents
About the VCC
Page 3
Contents, product information
Product options
Page 4
Media options and accessories
Installation & set up
Page 5
Connection
Network
switching
External connections
Parameters menu
Page 6
Terminal settings
Copier settings
Ping utility
Card reader test
Hostname
Network
settings
Page 7
Static IP/DHCP
Server/Subnet/Gateway
Domain server/DNS
MAC broadcast filter
Change settings
Troubleshooting
Page 8
Initial installation
Post installation
Copier set up
Timing parameters
Page 9
Leading/trailing edge debitin
g
Sense/blind time
Reset/eject delay
Firmware upgrade
Page 10
Network utility
Serial upgrade
PCB diagram
Page 11
Component
s placement
Copier interface schematic
Page 12
Product returns information
Virtual Cash Controller
product guide
–
page
3
Virtual Cash
Controller
2
Product Guide
Ab
out the
Virtual Cash C
ontroller
Your
VCC
terminal should arrive in good condition. Check
the carton for damage and store it in a safe place in the
event you need to return the machine. If there is any
visible damage to your machine, notify the shipping
co
mpany as soon as possible and contact your equipment
supplier.
Contents of package
Copier interface
Boscop
offers an extremely wide range of interface cables
for modern copiers and multifunction devices. We cater to
all brands: Canon,
Sharp
,Océ,Ricoh, Toshiba, Xerox,
Minolta,
and many others. Contact
Boscop
for details.
Keypad
The touch screen is fitted with an anti
-
splash membrane
to try and prevent accidental spill damage. Any liquid
caused damage is, however, not covered by our warranty
prog
ram.
Power supply
The switching power supply meets worldwide standards
and covers universal supplies from 90 to 264 VAC at
either 50 Hz or 60 Hz. In the event of failure or theft,
please contact Boscop, Inc.
1.
VCC
terminal
2.
Power cord
3.
S
witching power supply
4.
Warranty card
5.
I
nstaller guide
6.
Copier harness (option)
Product information
Take a few minutes to complete these details. Have the
information
ready when you call Boscop
with questions
about your product.
Product type:
Vi
rtual Cash
controller
Serial number:
___________________
(9 digits)
MAC address
:
____________________
(12 digits)
VCC
terminal shown on optional
Floor stand FS
-
1 (see following
page)
Virtual Cash Controller
product guide
–
page
4
VCC
product options
There are several produc
t options
available for the
VCC
terminal;
these
are governed by the
choice of user ID
media
for the system users.
ABA magnetic card reader
(track 2)
This will read any
ISO7810 track 2, magnetic card and
pass the information to the server software for
auth
entication. All credit cards, ATM cards, most student
ID cards, drivers licenses (US) use this format.
Boscop can
supply track 1 or track 3 by special order.
Barcode swipe reader
Ideally suited to printed barcodes where the barcode
is
printe
d in
the same position as a track 2 magnetic stripe.
Track 1 and track 3 positions may be catered for by
special order.
Codes read include
UPC/EAN/JAN & ADDON/25, CODE
39, CODE 39 FULL ASCII, CODE 32, INTERLEAVE 25,
INDUSTRIAL 25, MATRIX 25, CHINA POSTAGE,
CODE 128,
CODE 93, CODE 11, CODABAR/NW7, MSI/PLESSEY
,
TELEPEN
Mifare, iClass
RFID
card reader
Our 13.56MHz proximity reader version
can read either
iCLASS credentials (transmitting Wiegand
formatted data
as encoded), M
ifare®Standard, Ultralight, or DESF
ire®credentials (transmitting Wiegand
data based on the card
serial number in
various
formats).
N
ote–to read proprietary iClass formats we will need the
consent of the format owner.
HID Proximity card reader
Our HID 125kHz reader can read
26 and 34 b
it
HID
Proximity cards, as well as
any iClass cards using 125kHz
.
Note
–toread proprietary HID formats we will need the
consent of the format owner.
EM4102 proximity card reader
Mostly used in Europe, we have
fully integrated the
125kHz EM4102 and c
an supply readers to special order.
Impro 125kHz proximity card reader
We
have integrated
the Impro
Omni
-
Scan
reader
module;
this read only device has a scan range of up to 6”. It reads
Impro Standard, Impro Slim and Impro Pico credentials
.
Barcode scann
er
option
The
VCC
terminal can be supplied with a
n externally
mounted
barcode scanner
fixed underneath the terminal
for use when the barcode is either printed out of position
for use with a swipe reader or for use when libraries place
an adhesive backed ba
rcode onto a card, causing the
barcode to be out of position or crooked.
Codes read include
UPC/EAN/JAN & ADDON/25, CODE
39, CODE 39 FULL ASCII, CODE 32, INTERLEAVE 25,
INDUSTRIAL 25, MATRIX 25, CHINA POSTAGE, CODE 128,
CODE 93, CODE 11, CODABAR/NW7, MSI/
PLESSEY
,
TELEPEN
Floor stand FS
-
1
The optional stand is ergo
-
nomically designed to
promote greatest ease of use
of the ter
minal. Sloping the
keypad and display towards
the user, it is accessible by
both pedestrian and
wheelchair patrons and de
-
signed fo
r placement either at
the front or rear on either
side of the copier. All cables
are securely routed inside the
stand for maximum security.
Picture shows cabling routed
inside the stand upright.
Wall Mount WM
-1If space is at a premium and the equipment
has to be set
up against a wall or by a pillar then the optional wall
mount will help.
Track 2 stripe requirements are .25” wide and
positioned between .218” and .468” from the
card edge
Loading...