ROHM UCR01MVPJS Technical data

Table 1
UCR01 (1005 size : 1 / 8W)
Features
1) Superior rated power.
2) Stable, low resistance guaranteed regardless of the surrounding environment.
3) Thick film resistive elements were used to create this lineup of ultra-low resistance products ranging from 68m to 910m.
4) Chip resistors ideal for current detection.
5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Ratings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it.
Item Conditions Specifications
Rated power
Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°
100
80
60
40
POWER LOAD (%)
20
0
55 0 70 100 155 AMBIENT TEMPERATURE (°C)
Fig.1
C.
0.125W (1 / 8W) at 70°C
Rated voltage
Nominal resistance Operating temperature
The voltage rating is calculated by the following equation.
E= P×R
See Table 1.
E: Rated voltage (V) P: Rated power (W) R: Nominal resistance (Ω)
55°
C to + 155°C
Resistance range
(Ω)
0.068 to 0.091 (E24)
0.1 to 0.2 (E24)
0.22 to 0.91 (E24)
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Resistance tolerance Special specification
F (±1%) J (±5%)
S
L
Resistance temperature
coefficient (ppm/°C)
0 to 300 0 to 250 0 to 200
www.rohm.com
1/3
c
2010 ROHM Co., Ltd. All rights reserved.
2010.10 - Rev.B
Data Sheet UCR01
Characteristics
Item Test conditions (JIS C 5201-1)
Resistance
Variation of resistance with temperature
Overload
Solderability
Resistance to soldering heat
Rapid change of temperature
Guaranteed value
Resistor type
JIS C 5201-1 4.5 Measuring method : Measure under termination
F : ±1% J : ±5%
See Table.1
± (2.0%+0.005Ω)
A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage.
± (1.0%+0.005Ω)
No remarkable abnormality on the appearance.
± (1.0%+0.005Ω)
JIS C 5201-1 4.8 Measurement : +25 / +125°C
JIS C 5201-1 4.13 Rated voltage (current) × 2.5, 5s. 25
JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5 Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18 Soldering condition : 260±5 Duration of immersion : 10±1s.
JIS C 5201-1 4.19 Test temp. : 55
Under termination
°C
to +125°C 100cyc 0.5h
Terminal
°C
°C
°C
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of the end face plating
± (1.0%+0.005Ω)
± (5.0%+0.005Ω)
± (2.0%+0.005Ω)
± (1.0%+0.005Ω)
Without open.
JIS C 5201-1 4.24 60
°C, 95%RH
Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1
Rated voltage (current), 70
1.5h : ON 0.5h : OFF Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
°C
125 Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
°C, 60
s.
25 Solvent : 2-propanol
JIS C 5201-1 4.33
°C
www.rohm.com
2/3
c
2010 ROHM Co., Ltd. All rights reserved.
2010.10 - Rev.B
0.28±0.10
P
R
)
Data Sheet UCR01
Dimensions&Construction
(Surface)
(Cross section)
(Back side)
5 6 7 8
Part No. Explanation
UC 0R 1 M V P J S
1.00±0.10
4
3
0.34±0.10
0.55±0.1
221
0.37±0.05
No.
1
Alumina substrate
2
Silver thick film electrode
3
Resistive element
4
Over ciating
5
Nickel-chrome electrode
6
Nickel electrode
7
Copper electrode
8
Sn electrode
Material
Part No.
Resistance tolerance
F
±
1%
±
5%
J
ackaging Specifications Code
Part No.
UCR01
eel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
Resistance tolerance
Code Packaging specifications Reel
J(±5%) F(±1%)
MVP 10,000
Paper tape (2mm Pitch)
Packaging
Reel Taping
ABD
0 2
0 4
0 6
0 8
C
ABCD
φ180
0
1.5
φ60
+1
0
+1.0
9
0
Label
EIAJ ET-7200B compliant
(Unit: mm)
φ13±0.2
0 2
0 4
0 6
0 8
Special part number
S
0.068 to 0.091
L
0.1 to 0.91Ω
φ180mm (7in.)
Heat crimp cover tape
Thick paper
(Underside paper tape)
mount
WFEA0 B0
8.0±0.3 3.5±0.05 1.75±0.1
D0 P0 P1 P2 T2
+0.1
φ1.5
0
Nominal resistance
Ω
P0
P2 P1
4.0±0.1 2.0±0.05 2.0±0.05 Max. 1.1
Resistance code, 3 or 4 digits. 000 denotes jumper type.
Resistance
tolerance
FL, FS, JSJL::4 digits
A0
Chip resistor Square punchout hole
Resistance
Basic ordering unit(pcs
φD0
B0
(Unit: mm)
0.7±0.1 1.2±0.1
code
3 digits
E
F
W
T
2
www.rohm.com
3/3
c
2010 ROHM Co., Ltd. All rights reserved.
2010.10 - Rev.B
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd.
The content specied herein is subject to change for improvement without notice.
The content specied herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specications, which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specied in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.
The technical information specied herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information.
Notice
The Products specied in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, of ce-automation equipment, commu­nication devices, electronic appliances and amusement devices).
The Products specied in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, re or any other damage caused in the event of the failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel­controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specied herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved.
http://www.rohm.com/contact/
R1010
A
Loading...