查询RPM5300供应商
RPM5300 series
Photo Link Module
IR Receiver Module
RPM5300 series
RPM5300 series are remote contro l receiver mod ules. Small-siz ed, light-weight, and low curr ent consumpt ion modules
have been achieved by using resin mold.
zApplications
All household electric appliances su ch as TV, DVD, air conditioner and audio equ ipment.
zFeatures
1) Small size, SMD type.
2) Low current consumption. (300µA Typ.)
3) High ripple rejection.
4) Top view package type & Side view package type.
5) High sensitivity, such as leed type IR Receiver, because of using “the Dual Receiving Lens”.
zRPM5300 series
Sub carrier frequency
36.7kHz RPM5337-H12
37.9kHz
40.0kHz
SIDE VIEW
RPM5337-H14
RPM5338-H14
RPM5340-H14
zAbsolute maximum ratings (Ta = 25°C)
Parameter Symbol
Supply Voltage V
Storage temperature
Operating temperature
CC
Tstg
Topr
−30 to +100
−10 to +75
zRecommended operating conditions (Ta = 25°C)
Parameter Symbol Min. Typ. Max. Unit
V
Supply Voltage
CC
Limits
6.3
3.0 V2.7 3.6
TOP VIEW
RPM5338-H12
RPM5340-H12
Unit
V
°C
°C
1/7
Photo Link Module
zBlock diagram
RPM5300 series
CC
V
100k
I / V
AMP
LIMITER
Comparator
BPF
Demodulator
and integrator
zT ermina l description
Pin namePin No. Function
1V
2
3
4
5
6
7
CC
GND
GND
GND
OUT
R
GND
GND
POWER SUPPLY
GROUND
GROUND
GROUND
OUTPUT TERMINAL
GROUND
GROUND
zElectrical, Optical characteristics (Unless otherwise noted, Ta = 25°C V
Parameter Symbol Min. Typ. Max. Unit Conditions
−
Consumption Current I
Effective Distance
High Level Output Voltage
Low Level Output Voltage
ON Pulse Width
OFF Pulse Width
Center frequency
Horizontal half angle
Vertical half angle
∗1 600/600µs burst wave is transmitted by standard transmitter. However, it must be measured after the initial transmission pulse is 10 pulse.
∗2 It is an angle when the linear arrival distance become half.
∗3 Three types of frequencies : 36.7, 37.9, 40kHz.
CC
L
V
V
T
ON
T
OFF
fo
θ 1/2
θ 1/2
H
L
2.5
400
400
300 µA No outside light, No signal input
7
12
−
600
600
−
−
−
∗3
42
38
500
−
−
0.5
800
−
−
CC=5V)
m−
Outer light condition Ee < 10 (Ix)
V−
V
µs
µs800
<
Isink 200µA
=
Outer light condition Ee < 10 (Ix) ∗1
Outer light condition Ee < 10 (Ix) ∗1
kHz−
deg
deg
R
OUT
GND
∗1
∗1
∗1
∗2
∗2
2/7
Photo Link Module
z Measurement Conditions
(1) Transmit signal
RPM5300 series
600µs 600µs
Carrier frequency=fo, Duty=50%
Fig.1 Transmit signal
(2) Standard transmitter
λ peak=940nm
λ ∆=40nm
io=V
OUT
20cm
RPM-302B
Standard transmitter
R
Fig.2 Measurement of standard transmitter proofreading
/ R
V
OUT
When standard transmitter output the signal at Fig.1 standard photodiode output become io=5µAp-p under the
measurement condition Fig.2.
(The radiant intensity of standard transmitter : 50mW / sr)
RPM-302B : standard photodiode has short current Isc=27 µA at E=1000(lx)
(using CIE standard light sou rce A)
3/7
Photo Link Module
(3) Measurement effective distance, horizont al & vertical half angle
Standard transmitter
Effective distance : L
(θ ; Indicates horizontal and vertical directions)
RPM5300 series
RPM5300 series
θ
θ
Light detector face
illuminance : Ee
Fig.3 Measurement condition for effective distance
Effective distance L : Effective distance at θ=0° Fig.3
Horizontal & vertical half angle θ : The angle which effective distance became 50% of L.
(4) Output signal
600µs
Transmit signal
Output signal
T
ON
Fig.4
600µs
T
OFF
Carrier frequency=f
Carrier Duty=50%
V
CC
V
H
CC
1/2 V
V
L
GND
0
(5) Measurement circuit for the output voltage and the consumption current
I
V
CC
CC
A
RPM5300
R
OUT
GND
Fig.5
V
CC
V
V
H
,
V
L
4/7
RPM5300 series
Photo Link Module
zNotes
(1) All characteristics of th e receiver in this s pecification are s pecified by sup plying burst wave form (Fig. 1) with ROHM
standard transmitter (Fig.2 ).
If in case of other burst wave form w ill be used, p lease check th ese spec. Ca refully under the evaluations.
(2) When the receiver will be used as the w ire-less remote contro ller , please use the signal meth od the signal fo rmat
which refer to “Measures to prevent mulfunctioning of IR remote-controlled electric home appliances”. (Published July
1987 by Association of Electric Home Appliances)
If using other signal method, signal format, (ex: signal format which not including the leader signal) the receiver might
have chances to miss-functio n.
(3) Please set up transmitter’s carrier frequency as same as the receiver’s f
occurred.
(4) If transmission signal has non-continues carrie r , error might be occurred . Continuous carrier is nece ssary.
0 frequency. Otherwise error might be
T1
(5) The receiver was designed to use as in-door use only.
Therefore, please understand that the receiver cannot cover all characteristics, in case of using it out-door.
(6) Noise environment (Light noise from inverter Lamp, and other kind of Lamps, Power ripple, electromagnetic noise from
power circuit, and etc) may cause a reduced effective distance.
(7) The receiver may not w ork properly if re ceiving signal judgem ent is done by single pulse due to the
surrounding / environmental noises.
To preven t such misjudgement, please ma ke sure that the rece iver is set up to w ork only when receiving
series of coded signal.
(8) Emitting unit (remote control transmitter) has to be considered about its emitting device function, characteristics and
characteristics of the receiver.
(9) Please connect ‘Holder’ on to the ‘Ground (GND)’ of PCB. If the holder is not connected to the GND, there is a
possibility of worsening the characteristics of product.
(10) Do not supply unnecessary stress to lead.
(11) Please pay careful attention to the lens.
It might have a chance to miss-function when the lens get dust or dirty. And also please do not touch the lens.
(12) In order to prevent products from ESD, human body and solder iron, etc. are required to be grounded.
T1≠T2
T2
5/7
Photo Link Module
zElectrical and optical characteristics curves
1.00
0.00
−2.00
120
100
100
RPM5300 series
80
Gain : (dB)
−4.00
−6.00
−8.00
fo=37.9kHz
fo=36.7kHz
fo=40.0kHz
60
40
20
Relative effective distance : (%)
−10.00
34.00 36.00
38.00 40.00 42.00
Frequency : (kHz)
Fig.6 BPF characteristic
0
−90 −75 −60 −45 −30 0−15 30 4515 60 75 90
Angle : (˚)
Fig.7 Direction characteristic
(Horizontal direction)
120
100
80
60
40
20
Relative effective distance : (%)
0
−90 −75 −60 −45 −30 0−15 30 4515 60 75 90
Angle : (˚)
Fig.8 Direction characteristic
(Vertical direction)
6/7
Photo Link Module
zExternal dimensions (Unit : mm)
RPM5300 series
4.0
1.0
2.2
1.0
2.9
0.56
17
P0.95×7=6.65
0.6±0.1
0.65
1.1
1.4
4.0
A
0.37±0.1
0.95
0.48
8.0
MOUNTING CENTER
2.802.80
2.2
0.15±0.1
2.59
Expanded Figure of
2.67
NOTE
1.TOLERANCE :
2.COPLANARITY : 0.1mmMAX
UNIT : mm
A part
2.2
±
0.2mm
0.75
RSLP7A-H12RSLP7A-H14
MOUNTING CENTER
7.6
0.1
3.0±0.1
3.0
4.0
8.0
5.6
2.8
2.72
0.56
0.68 0.37±0.1
P0.95×7=6.65
0.6±0.1
0.20.65
0.1
±
±
0.6
1.2
2.49
0.1
±
0.75
2.4
0.1
±
NOTE
0.15
TOLERANCE :
COPLANARITY : 0.1mmMAX
UNIT : mm
±
0.2mm
2.0
ETH672
ETH658
7/7
Appendix
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
Notes
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
Loading...