ROHM PML10EZPJV Technical data

Ultra-low Ohmic Resistors for Current Detection(Wide terminal type)

PML10

Features

1) Ultra-low resistance range

2) Wide terminal configuration for high joint reliability.

3) Unique trimless structure utilized for improved current detection accuracy.

4) ISO9001- / ISO/TS 16949- approved

Rating

Item Conditions Specifications

Rated power

For resistors operated at the ambient temperature in
excess of 70°C, the load shall be derated in accordance with Fig.1

100

80

60

40

POWER LOAD (%)

20

0

−55 0 70 100 125 155

AMBIENT TEMPERATURE (°C)

Fig.1

0.66W
at 70°C

Rated voltage
Rated current

Nominal resistance See Table 1.

Operating temperature

Rated voltage and current are determined from the following.

E= P×R

E= P

Table.1

RESISTANCE

(mΩ)

1.0, 1.2, 1.5

1.8, 2.0, 2.4,

2.5

TOLERANCE

G (±2%)

J (±5%)

/

R

SPECIAL

CODE

V

E: Rated voltage (V)
I :

Rated current (A)

P: Rated power (W)

Resistance (Ω)

R:

TEMPERATURE (ppm / ˚C)

COEFFICIENT

±200

−55°C to +155°C

www.rohm.com

1/3

c

2011 ROHM Co., Ltd. All rights reserved.

○

2011.10 Rev.B

PML10

Characteristics

Item Test conditions (JIS C 5201-1)

Resistance

Guaranteed value

Resistor type

G : ±2%
J : ±5%

Data Sheet

JIS C 5201-1 4.5
Measuring method : Measure under
terminations by 4 probes.

Fig.2 (Under terminations)

probes

Variation of resistance
with temperature

Overload

Solderability

Resistance to
soldering heat

Rapid change of
temperature

Damp heat, steady state

Endurance at 70°C

Endurance

Component Solvent
Resistance

Bend strength of
the end face plating




See Table.1

± 2.0%

A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.

± 1.0%

No remarkable abnormality on the appearance.

± 1.0%

± 3.0%

± 3.0%

± 3.0%

± 0.5%

Without open.

JIS C 5201-1 4.8
Measurement : +25 / −55 / +25 / +125°C

JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.

JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5
Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.18
Soldering condition : 260±5
Duration of immersion : 10±1s.

JIS C 5201-1 4.19
Test temp. : −55

JIS C 5201-1 4.24
40

°C, 93%RH

Test time : 56days

JIS C 5201-1 4.25.1
70

°C,

Rated power

1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h

JIS C 5201-1 4.25.3

°C

155
Test time : 1,000h to 1,048h

JIS C 5201-1 4.29
23

°C±5°C

Solvent : 2-propanol

JIS C 5201-1 4.33

°C

to +125°C 5cyc

°C

°C



www.rohm.com

2/3

c

2011 ROHM Co., Ltd. All rights reserved.

○

2011.10 Rev.B

PML10

Dimensions&Construction



(The Surface)

1L00

(The back)

(The cross section)

a

a

W

Data Sheet

±

L

L 0.15

No.

Resistive metal element (Ni-Cr Alloy)

Primary electrode(Cu)

External electrode(Sn)

Overcoat (Resin : Black)

Marking (Resin : Yellow)

t

Measure

±

W 0.15

*Each value range varies with the resistance.

Material

±

t 0.15

0.422.01.20

±

a 0.2

0.45 to 0.3*





Part No. Explanation

PM 1L

Part No.

Packaging Specifications Code

Part No.

PML10

Reel (φ180) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product





Packaging

ABD

Code

EZP

Resistance tolerance

±5%)

J(

G(±2%)

Reel Taping

0 2

0 4

0 6

0 8

0 E Z P J V

Resistance tolerance

±2%

G

±5%

J

Packaging specifications Reel

Paper tape (4mm Pitch)

0 2

0 4

0 6

0 8

Special part number

Base paper

Bottom Tape

Top tape

φ

180mm

P

0

P

2

P

Components Cavity

Nominal resistance

Resistance code, 3 or 4 digits.

Resistance

tolerance

JG::3 digits

Resistance

Value

1mΩ

1.2mΩ 1L2 1L20

1.5mΩ 1L5 1L50

1.8mΩ 1L8 1L80
2mΩ

2.4mΩ

2.5mΩ 2L5 2L50

1

φD

0

B

0

A

0

Resistance

code

4 digits

Resistance Tolerance

JG

1L0

1L00

2L0 2L00

2L4

2L40

Basic ordering unit (pcs)

5,000

E

F

W





C

ABCD

φ180

0

−1.5

φ60

+1

0

9

+1.0

0

Label

EIAJ ET-7200B compliant

(Unit : mm)

φ13±0.2

WF EA0B

8.0±0.3 3.5±0.05 1.75±0.1

D

φ1.5

0

+0.1

P

0

4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1

0

P

1

1.65

P

+0.2

−0.1

2

T2

(Unit : mm)

0

+0.2

2.4

−0.1

T

2

www.rohm.com

3/3

c

2011 ROHM Co., Ltd. All rights reserved.

○

2011.10 Rev.B

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.

The content specied herein is subject to change for improvement without notice.

The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.

The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.

The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu­nication devices, electronic appliances and amusement devices).

The Products specied in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transpor tation equipment, aerospace machinery, nuclear-reactor controller, fuel­controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.

Notice

www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.

Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

R1120

A