Compact 8-element Chip Resistor Networks
MNR15 (06035 size)
Features
1) Suitable for pull-up and pull-down resistors.
2) No direction to be mounted by placing common electrode with symmetry.
3) Convex electrodes
Easy to check the fillet after soldering is finished.
4) High-density mounting
Can be mounted even densely than eight 0402chips (MCR01), and mounting costs are lower.
5) Compatible with a wide range of mounting machines.
Squared corners make it excellent for mounting using image recognition machines.
6) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
Ratings
Item Conditions Specifications
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
POWER LOAD (%)
20
0
−55 0 70 100 125
AMBIENT TEMPERATURE (°C)
Fig.1
0.031W (1 / 32W)
at 70°C
Rated voltage
Nominal resistance
Operating temperature
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E : Rated voltage (V)
E = P × R
See Table 1.
P : Rated power (W)
R : Nominal resistance (Ω)
Table 1
Resistance tolerance
J (±5%)
∗Before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loads),
be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be
guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Resistance range
(Ω)
56≤R≤100k (E24)
Resistance temperature coefficient
(ppm /
±200
°C
)
Limiting element voltage 12.5V
−55°C to +125°C
www.rohm.com
1/3
○c 2011 ROHM Co., Ltd. All rights reserved.
2011.12 - Rev.E
MNR15 (06035 size)
Characteristics
Item Test conditions (JIS C 5201-1)
Resistance
Guaranteed value
Resistor type
J : ±5%
Data Sheet
JIS C 5201-1 4.5
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
Dimensions (Unit : mm)
See Table.1
± (2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
± (1.0%+0.05Ω)
No remarkable abnormality on the appearance.
± (1.0%+0.05Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (1.0%+0.05Ω)
± (1.0%+0.05Ω)
Without mechanical damage such as breaks.
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
JIS C 5201-1 4.13
Rated voltage×2.5, 2s.
Maximum Overload Voltage : 25V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5
°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5
°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. : −55
°C
to +125°C 5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage, 70
°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
°C
125
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
°C
, Immersion cleaning, 5±0.5min.
23±5
Solvent : 2-propanol
JIS C 5201-1 4.33
a
Cross section A−A'
Cross sectionB−B'
3.2±0.1
bb
∗∗∗∗
a : 0.48±0.15
b : 0.32±0.15
B
Resistive element (Oxide metal thick film)
A'A
1.6±0.1
∗0.64
B'
0.1
±
0.5
1
1
Maqnification
0.3±0.1
0.3±0.1
Silver thick film electrode
Nickel electrode
Sn electrode
Alumina substrate
Overcoating (Resin)
Pitch of the upper electrode.
∗
MaterialNo.
www.rohm.com
2/3
○c 2011 ROHM Co., Ltd. All rights reserved.
2011.12 - Rev.E
Loading...