Compact Chip Resistor Networks
MNR02 (1005 2 size)
Features
1) Extremely small and light
Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced.
3) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors have obtained ISO9001- / ISO/TS 16949- certification.
Ratings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering
it.
Item Conditions Specifications
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
POWER LOAD (%)
20
0
−55 0 70 100 125 155
AMBIENT TEMPERATURE (°C)
Fig.1
0.063W (1 / 16W)
at 70°C
Rated voltage
Nominal resistance See Table 1.
Operating temperature
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
E = P×R
P: Rated power (W)
R: Nominal resistance (Ω)
Limiting element voltage
−55°C to +155°C
25V
Jumper type
Resistance
Rated current
Operating temperature
Table 1
Resistance tolerance
J (±5%) 10 to 1M (E24) ±200
Max. 50mΩ
1A
−55°C to +155°C
Resistance range
(Ω)
Resistance temperature coefficient
(ppm / °C)
Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
www.rohm.com
1/3
○c 2011 ROHM Co., Ltd. All rights reserved.
2011.12 - Rev.F
MNR02 (1005 2 size)
Characteristics
Items Test conditions (JIS C 5201-1)
Resistance
Guaranteed value
Resistor type Jumper type
J : ±5%
MAX.50mΩ
Data Sheet
JIS C 5201-1 4.5
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
Dimensions (Unit: mm)
1.0±0.1
B
B'
0.34
+0.05
−0.1
A'A
1.0±0.1
+0.1
0.33
−0.05
See Table.1
± (2.0%+0.1Ω)
MAX.50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
± (1.0%+0.05Ω)
MAX.50mΩ
No remarkable abnormality on the appearance.
± (1.0%+0.05Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (1.0%+0.05Ω)
± (1.0%+0.05Ω)
MAX.50mΩ
MAX.100mΩ
MAX.100mΩ
MAX.100mΩ
MAX.50mΩ
MAX.50mΩ
Without mechanical damage such as breaks.
1
5
2 3 4
6
5
1
6
Cross section A-A'
0.2±0.1
0.25±0.1
Cross section B-B'
0.35±0.1
JIS C 5201-1 4.8
Measurement : +25 / +125°C
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. : −55
°C to
+125°C 5cyc
JIS C 5201-1 4.24
°C, 93%RH
40
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
°C
125
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
°C
, Immersion cleaning, 5±0.5min.
23±5
Solvent : 2-propanol
JIS C 5201-1 4.33
No.
1
Resistive element (Oxide metal thick film)
2
Silver thick film electrode
3
Nickel electrode
4
Sn electrode
5
Alumina substrate
6
Overcoating (Resin)
Material
°C
°C
°C
0.68
Equivalent circuit
R1
R2
R1 = R2
www.rohm.com
2/3
○c 2011 ROHM Co., Ltd. All rights reserved.
2011.12 - Rev.F
MNR02 (1005 2 size)
Packaging
Reel Taping
0 2
0 4
0 6
(RRM)
0 8
compliant
ABD
A
B
D
0 2
0 4
0 6
0 8
C
Label
EIAJ ET-7200B
P0
P2
A
0
0
B
Heat crimp cover / Tape
Thick paper
(Underside paper tape)
mount
WF EA0B
8.0±0.3 3.5±0.05 1.75±0.1 1.17±0.1 1.17±0.1
D
0
P
0
+0.1
φ1.5
4.0±0.1 2.0±0.1 2.0±0.05 Max. 0.5
0
P1
φD
0
Chip network
resistors
P
1
Square punchout hole
P
2
E
F
(Unit: mm)
0
T
2
Data Sheet
W
2
T
+1.0
9
0
Label
EIAJ ET-7200B (RRV)
(Unit: mm)
φ13±0.2
C
ABCD
φ180
0
−1.5
φ60
+1
0
Part No. Explanation
Part No.
Packaging Specifications Code
Part No.
MNR02 M0AP
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
Resistance tolerance
Code
J(±5%)
Packaging specifications
Paper tape (2mmPitch)
compliant
P
Reel
φ180mm
Resistance tolerance
J ±5%
J is also used
for jumper.
Basic ordering unit (pcs)
10,000
Nominal resistance
Resistance code, 3
000 denotes jumper type.
Resistance
tolerance
J
Resistance
code
3digits:
www.rohm.com
3/3
○c 2011 ROHM Co., Ltd. All rights reserved.
2011.12 - Rev.F
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specied herein is subject to change for improvement without notice.
The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specied in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Notice
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
R1120
A
Loading...