ROHM MCR01MZPFL Technical data

Low Ohmic Thick Film Chip Resistors

MCR01 (1005 size (0402 size) : 1 / 16W)

Features

1) Power rating of 1 / 16W

2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.

4) ROHM resistors have approved ISO9001- / ISO/TS16949- certification.

Ratings

Design and specifications are subject to change without notice.
Carefully check the specification sheet before using or ordering it.

Item Conditions Specifications

Rated power

Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°

100

80

60

40

POWER LOAD (%)

20

0

−55 0 70 100 155

AMBIENT TEMPERATURE (°C)

Fig.1

C

.

0.063W (1 / 16W)

at 70°C

Rated voltage

Nominal resistance

Operating temperature

The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

E= P×R

See Table 1.

P: Rated power (W)

R: Nominal resistance (Ω)

Limiting element voltage 0.76V (9.1Ω)

C to + 155°C

−55°

Table 1

Resistance tolerance

F(±1%)

Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.

Special
specification

L

Resistance range

(Ω)

1.0 to 9.1

(E24)

Resistance temperature coefficient

(ppm/°C)

±400

www.rohm.com

1/3

○c 2011 ROHM Co., Ltd. All rights reserved.

2011.11 - Rev.D

MCR01 (1005 size (0402 size) : 1 / 16W)

Data Sheet



Characteristics

Item Test conditions (JIS C 5201-1)

Resistance

Variation of resistance
with temperature

Overload

Solderability

Resistance to
soldering heat

Rapid change of
temperature

Damp heat, steady state

Endurance at 70°C

Endurance

Resistance to solvent

Bend strength of
the end face plating

Dimensions (Unit : mm)

Guaranteed value

Resistor type

F : ±1%

See Table.1

± (2.0%+0.005Ω)

A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.

± (1.0%+0.005Ω)

No remarkable abnormality on the appearance.

± (1.0%+0.005Ω)

± (3.0%+0.005Ω)

± (3.0%+0.005Ω)

± (3.0%+0.005Ω)

± (0.5%+0.005Ω)

± (1.0%+0.005Ω)

Without mechanical damage such as breaks.

JIS C 5201-1 4.5

Load voltage : A
Measuring method : measure upper termination
by 4 proves.

Upper termination

Prove

JIS C 5201-1 4.8
Measurement : +25 / −55 / +25 / +125°C

JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.

JIS C 5201-1 4.17
Rosin-Ethanol (25%WT)
Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.18
Soldering condition : 260±5

°C

Duration of immersion : 10±1s.

JIS C 5201-1 4.19

°C

Test temp. : −55

to +125°C 5cyc

JIS C 5201-1 4.24
40

°C, 93%RH

Test time : 56days

JIS C 5201-1 4.25.1

°C,

Rated voltage

70

1.5h : ON − 0.5h : OFF
Test time : 1,000h

JIS C 5201-1 4.25.3

°C

155
Test time : 1,000h to 1,048h

JIS C 5201-1 4.29
23

°C±5°C

, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.33

1

0.2±0.1

0.25+0.05

−0.1

1.0±0.05

5

6

0.35±0.05

0.5±0.05

2

3

4

No.

1

Resistive element (Oxide metal thick film)

Silver thick film electrode

2

Nickel electrode

3

Sn electrode

4

Alumina substrate

5

Overcoating (Resin)

6

Material

www.rohm.com

2/3

○c 2011 ROHM Co., Ltd. All rights reserved.

2011.11 - Rev.D