Page 1
A
Thick Film Thermal Printhead (300d pi)
KD3003-DC92A
KD3003-DC92A is developing type of GL40 se ries which are de veloped mainly for label printe rs.
We have adopted low coefficient of abrasio n and c ond uctive pr otect ion co at to GL40 seri es which are possib le for h igh sp eed and
good printing quality.
That is KD3003-DC92A which is 24V standard thick film therm al print head with high spee d, high qu ality of p rinting, h igh dura bility ,
long life, and strong resistance to abration.
zApplications
High speed label printer
Food label printer
High speed ticket printer
High speed terminal printer
zFeatures
1) Perform 150km life time adopting new protective coat.
(Perform three times life time by coe fficient o f abrasion w hich is about is about 1 /10 of current mass-p roducing coat.)
2) Build in thermal high speeded heater and perfo rm high printing 4 IPS. (100mm / s)
3) Available for thermal transfer printing by adopting specific partial glaze.
zDimensions (Unit : mm)
(4.844)
(3)
Max.36
Max.45
#2
#1
HIROSE HIF3FC-20PA-2.54DS
91
81.312(Effetive Print Width)
DOT #960
#20
#19
DOT #1
#6
JST B6PS-VH
TYPE OF PRINTHEAD
#1
Max.φ
20
Max.5.5
6.1±0.4
(5)
Max.10
φ3H10 Length 4
(Effective Depth 3)
0.5
±
(20.8)
25
3-M3(Effective Depth 3)
40±0.3
60.5±0.3
φ3H10
(Effective Depth 3)
20.656±0.2
20±0.3
DOT #960
20.5±0.3
0.3
0.2
0.3
±
±
±
7.3
15.3
17.8
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
1/3
2009.01 - Rev.
Page 2
A
Fig. 1
S
S
S
S
KD3003-DC92A Data Sheet
zEquivalent circuit
VH
DOT #960 DOT #1
GND
V
DD
TB4
TB3
TB2
TB1
LAT
CLK
DI4
DO4
DI3
DO3
DI2
DO2
DI1
DO1
TM
TM
CONNECTOR
DI No.
DI1 1 to 256 1 to 256
DI2
DI3
DI4
960 769 768 513 512 257 256 1
LATCH REGISTER
SHIFT
REGISTER
DOT No. STB No.
SHIFT
REGISTER
SHIFT
REGISTER
THERMISTOR
30k
Ω
B : 3950K
DOT No.
STB1
257 to 512
513 to 768
769 to 960
STB2
STB3
STB4
257 to 512
513 to 768
769 to 960
SHIFT
REGISTER
zPin configuration
CONNECTOR A CONNECTOR B
No.
10
Circuit
1
2
3
4
5
6
7
8
9
GND
DD
V
GND
DD
V
STB4
CLK
DI4
DO4
STB3
LAT
No.
11
12
13
14
15
16
17
18
19
20
Circuit
TM
TM
DI3
DO3
DI2
DO2
STB2
STB1
DI1
DO1
No.
Circuit
1
2
3
4
5
6
VH
VH
VH
GND
GND
GND
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
2/3
2009.01 - Rev.
Page 3
A
C
D
"
"
D
"
"
L
S
D
"
"
0.40
.5
e
8
O.D
0
KD3003-DC92A Data Sheet
zTiming chart
Min.30ns
LOCK (CLK)
Max.120ns
Fig.2
Min.10ns
Min.100ns
Min.300ns
Max.10µs
Min.50nsMin.200ns
Max.10µs
ATA IN (DI)
High" : BLACK
Low" : WHITE
ATA OUT (DO)
High" : BLACK
Low" : WHITE
ATCH (LAT)
High" : HOLD
Low" : THROUGH
TROBE (STB)
RIVER OUT
Min.30ns
zCharacteristics
Parameter
Effective printing width
Dot pitch
Total dot number
Average resistance value
Applied voltage
Applied power
Print cycle
Maximum number of dots energized simultaneously
Maximum clock frequency
Maximum roller diameter
Running life / pulse life
Operating temperature
Symbol Typ. Unit
−
−
−
Rave
H
V
P
O
SLT
−
−
−
−
−
81.31
0.0847
960
1250
24
0.53
0.83
960
12
φ20.0
150 / 1×10
5 to 45
8
mm
mm
dots
Ω
V
W / dot
ms
dots
MHz
mm
km / pulses
˚C
zDat a sheet
0.35
0.30
0.25
0.20
0.15
ENERGY : (mJ / dot)
0.10
0.50
0
022
0.5 1 1.5
SLT : (ms / line)
Fig.3 Maximum energy curve
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.1
ENERGY : (mj / dot)
Fig.4 Representative density curv
SPEED : 4IPS
180
160
140
120
kΩ)
100
80
60
RESISTANCE : (
40
20
0
−20 −100 1020304050607
TEMPERATURE : (˚C)
Fig.5 Thermistor curve
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
3/3
2009.01 - Rev.
Page 4
Appendix
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account
when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no re-
sponsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples
of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to
use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no re-
sponsibility whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment
or devices (such as audio visual equipment, office-automation equipment, communication devices, elec-
tronic appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear
no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intend-
ed to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Notes
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2009 ROHM Co.,Ltd.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix-Rev4.0
Loading...