Page 1
A
Thick Film Thermal Printhead (300d pi)
KD3002-DC92A
KD3002-DC92A is developing type of GL40 se ries which are de veloped mainly for label printe rs.
We have adopted low coefficient of abrasio n and c ond uctive pr otect ion co at to GL40 seri es which are possib le for h igh sp eed and
good printing quality.
That is KD3002-DC92A which is 24V standard thick film therm al print head with high spee d, high qu ality of p rinting, h igh dura bility ,
long life, and strong resistance to abration.
zApplications
High speed label printer
Food label printer
High speed ticket printer
High speed terminal printer
zFeatures
1) Perform 150km life time adopting new protective coat.
(Perform three times life time by coe fficient o f abrasion w hich is about is about 1 /10 of current mass-p roducing coat.)
2) Build in thermal high speeded heater and perfo rm high printing 4 IPS. (100mm / s)
3) Available for thermal transfer printing by adopting specific partial glaze..
zDimensions (Unit : mm)
HIROSE HIF3FC-20PA-2.54DS
(5.396)
DOT #640
Max.36
Max.45
TYPE OF PRINTHEAD
65
54.208(Effetive Print Width)
DOT #1
(3)
Max.φ20
#4
#1
JST B4PS-VH
#20#2
#1
#19
Max.5.5
6.1±0.4
(5)
Max.10
φ
3H10 Length 4
(Effective Depth 3)
0.5
±
25
(20.8)
3-M3(Effective Depth 3)
φ
3H10
(Effective Depth 3)
55.5±0.3
55
±
56±0.3
0.3
0.896±0.2
28±0.3
DOT #640
0.3
0.3
±
±
7.3
15.3
0.2
±
17.8
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
1/3
2009.01 - Rev.
Page 2
A
Fig. 1
S
S
KD3002-DC92A
zEquivalent circuit
VH
DOT #640 DOT #1
Data Sheet
GND
V
DD
TB2
TB1
N.C.
LAT
CLK
DI2
DO2
DI1
DO1
TM
TM
CONNECTOR
DI No.
DI1 1 to 320 1 to 320
321 to 640 321 to 640DI2
#640 #321 #320 #1
LATCH REGISTER
SHIFT
REGISTER
THERMISTOR
Ω
B : 3950K
30k
DOT No. STB No.
STB1
STB2
SHIFT
REGISTER
DOT No.
zPin configuration
CONNECTOR A
No.
10
Circuit
1
2
3
4
5
6
7
8
9
GND
V
DD
GND
DD
V
STB2
CLK
D I 2
DO2
STB1
LAT
No.
11
12
13
14
15
16
17
18
19
20
Circuit
TM
TM
D I 1
DO1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
CONNECTOR B
No.
1
2
3
4
Circuit
VH
VH
GND
GND
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
2/3
2009.01 - Rev.
Page 3
A
C
D
"
"
D
"
"
L
S
D
"
"
0.40
.5
e
8
O.D
180
0
KD3002-DC92A
zTiming chart
LOCK (CLK)
Data Sheet
Min.30ns
ATA IN (DI)
High" : BLACK
Low" : WHITE
ATA OUT (DO)
High" : BLACK
Low" : WHITE
ATCH (LAT)
High" : HOLD
Low" : THROUGH
TROBE (STB)
RIVER OUT
Min.30ns
Max.120ns
Fig.2
Min.10ns
Min.100ns
Min.300ns
Max.10µs
Min.50nsMin.200ns
Max.10µs
zCharacteristics
Parameter
Effective printing width
Dot pitch
Total dot number
Average resistance value
Applied voltage
Applied power
Print cycle
Maximum number of dots energized simultaneously
Maximum clock frequency
Maximum roller diameter
Running life / pulse life
Operating temperature
Symbol Typ. Unit
−
−
−
Rave
V
H
P
O
SLT
−
−
−
−
−
54.21
0.0847
640
1250
24
0.55
0.83
640
12
φ20.0
150 / 1×10
5 to 45
8
mm
mm
dots
Ω
V
W / dot
ms
dots
MHz
mm
km / pulses
°C
zDat a sheet
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.1
SPEED : 4IPS
ENERGY : (mj / dot)
Fig.4 Representative density curv
160
140
120
kΩ)
100
80
60
RESISTANCE : (
40
20
0
−20 −10 10 30 50 7
0204060
TEMPERATURE : (˚C)
Fig.5 Thermistor curve
0.35
0.30
0.25
0.20
0.15
ENERGY : (mJ / dot)
0.10
0.50
0
022
0.5 1 1.5
SLT : (ms / line)
Fig.3 Maximum energy curve
www.rohm.com
c
○
2009 ROHM Co., Ltd. All rights reserved.
3/3
2009.01 - Rev.
Page 4
Appendix
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account
when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no re-
sponsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples
of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to
use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no re-
sponsibility whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment
or devices (such as audio visual equipment, office-automation equipment, communication devices, elec-
tronic appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear
no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intend-
ed to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Notes
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2009 ROHM Co.,Ltd.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix-Rev4.0
Loading...