ROHM BP3595 User Manual

Download

PRODUCTS

HYBRID IC

TYPE

BP3595

Precaution on using ROHM Products

●

1) Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronics appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Special Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications.

2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures.

[a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3) Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or

dust

[c] Use of our Products in places where the Products are exposed to sea winds or corrosive gases,

including Cl

, H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or

electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other

flammable items [f]Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes,

cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

4) The products might receive the radio wave interference from electronic devices such as Wireless LAN devices, Bluetooth devices, digital cordless telephone, microwave oven and so on that radiate electromagnetic wave.

5) The Products are not subject to radiation-proof design.

6) Please verify and confirm characteristics of the final or mounted products in using the Products.

DESIGN CHECK APPROVAL

DATE: 21/Oct./2015

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PAGE

1/22

TSZ22111･04･002

REV.B

PRODUCTS

HYBRID IC

TYPE

7) This product is a specification to radiate the radio wave. It is necessary to acquire the attestation of decided Radio Law of each region used to use the equipment that radiates the radio wave.

Please inquire about the attestation of Radio Law that this product acquires.

8) Confirm that operation temperature is within the specified range described in the product specification.

9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from

what is defined in this document.

● Precautions Regarding Application Examples and External Circuits

1) If change is made to the constant of an external circuit, please allow a sufficient margin considering

variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics.

2) You agree that application notes, reference designs, and associated data and information contained in this

document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise you own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for damages, expenses or losses incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

●

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please

take proper caution in your manufacturing process and storage so that voltage exceeding Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

● Precaution for Storage / Transportation

1) Product performance and soldered connections may deteriorate if the Products are stored in the places

where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl [b] the temperature or humidity exceeds those recommended by ROHM Temperature: 5℃～40℃, Humidity 40%～60% [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic

2) Even under ROHM recommended storage condition, connector mating of products over 1 year old

may be degraded.

3) Store / transport cartons in the correct direction, which is indicated on a carton as a symbol. Otherwise

bent leads may occur due to excessive stress applied when dropping of a carton.

Precaution for product label

●

QR code printed on ROHM product label is for ROHM’s internal use only, and please do not use at

customer site.

Precaution for disposition

●

When disposing Products please dispose them properly using an authorized industry waste company.

BP3595

PAGE

2/22

, H2S, NH3, SO2, and NO2

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

！

● Precaution Regarding Intellectual Property Rights

1) All information and data including but not limited to application example contained in this document is

for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data.

2) ROHM shall not have any obligations where the claims, actions or demands arising from the combination

of the Products with other articles such as components, circuits, systems or external equipment (including software)

3）No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of

ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein.

● Other Matters

1) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM.

3) In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons.

4) The proper names of companies or products described in this document are trademarks of registered trademarks of ROHM, its affiliated companies or third parties.

HYBRID IC

TYPE

BP3595

PAGE

3/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

HYBRID IC

TYPE

BP3595

PAGE

4/22

1. STRUCTURE

P.C.BOARD ASSEMBLY

2. PRODUCTS

HYBRID INTEGRATED CIRCUIT

3. TYPE

BP3595

4. APPLICATION

COMMUNICATION APPLIANCE

5. FUNCTION

WIRELESS LAN COMMUNICATION

6. ABSOLUTE MAXIMUM RATINGS

No. PARAMETER SYMBOL LIMITS UNIT REMARKS

Power supply voltage

2 Operating temperature range Topr

3 Storage temperature range Tstg

VCC

-0.3 ～ +3.6

V DC

-40 ～ +85 ℃

condensation

Note) These are the values that must not be exceeded at any time under any application or any test conditions.

Please make design keeping enough margins accordingly.

7. RECOMMENDED OPERATING CONDITIONS

No. PARAMETER SYMBOL

MIN. TYP. MAX.

SPEC

UNIT REMARKS

1 Power supply voltage VCC 3.1 3.3 3.5 V 2 Operating temperature range Ta -40 25 85 ℃ -

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

8. MAIN CHARACTERISTICS

No. PARAMETER CHARACTERISTICS

HYBRID IC

TYPE

BP3595

PAGE

5/22

1 Frequency width 2 Frequency tolerance Within ±25ppm

3 RF output power (*1)

4 Supported data rates

5 Receiving sensitivity (*1)

6 Security function 64bit/128bit WEP, TKIP, AES (*2)

7 Host Interface

8 Power supply voltage SINGLE 3.3V

(*1) “RF output power” and “Receiving sensitivity” are performance value that is at the electricity supplying point for

antenna in the below figure.

(*2) 64bit/128bit WEP, TKIP, and AES are everything processed with hardware.

9. BLOCK DIAGRAM

2,400MHz ～ 2,483.5 MHz（ch1～ch13）

IEEE802.11b： 15dBm±2dB IEEE802.11g： 13dBm±2dB IEEE802.11n： 12dBm±2dB

IEEE802.11b： 1 ～ 11Mbps IEEE802.11g： 6 ～ 54Mbps IEEE802.11n： 6.5 ～ 72.2Mbps

IEEE802.11b： -94dBm @1Mbps, -89dBm @11Mbps IEEE802.11g： -92dBm @6Mbps, -73dBm @54Mbps IEEE802.11n： -90dBm @6.5Mbps, -68dBm @72.2Mbps

USB2.0 (High-Speed mode) SDIO Ver.2.00 (High-Speed mode) UART (～921600bps)

Fig 1. Block diagram

・ A Flash memory (option) is necessary for use the flash boot function.

REV.B

TSZ22111･05･002

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

HYBRID IC

TYPE

BP3595

10. ELECTRICAL CHARACTERISTICS

CONDITIONS：Ta=25℃, VCC=3.3V, GND=0.0V

SPEC

No. PARAMETER CONDITION

UNIT REMARKS

MIN. TYP. MAX.

240 300 360 mA Continuous 280 340 400 mA Continuous (With USB)

160 200 240 mA 200 240 280 mA With USB

1 Consumption current

Sending

Receiving

Sleep mode - 1 - mA -

2 Center frequency - 2412 - 2472 MHz 3 Frequency tolerance - -25 - 25 ppm -

At electricity supplying

point for antenna

At electricity supplying

point for antenna

At electricity supplying

point for antenna

Side-lobe

4 RF output power

Unnecessary

out-of-band radiation

Transmit spectrum

mask

11b：11Mbps 13 15 17 dBm

11g：54Mbps

11 13 15 dBm

11n：MCS7 10 12 14 dBm

- - - 2.5 uW/MHz -

DSSS 11Mbps

OFDM

54Mbps

- - -30 dBr 1

- - -50 dBr 2

- - -20 dBr ±11MHz

- - -28 dBr ±20MHz

- - -40 dBr ±30MHz PER<8%

11b：11Mbps

- -89 -76 dBm

At electricity supplying

point for antenna

PER<10%

7 Receiving sensitivity

11g：54Mbps -73 -65 dBm

At electricity supplying

point for antenna

PER<10%

11n：MCS7

- -68 -64 dBm

At electricity supplying

point for antenna

Unnecessary

radiation

for receiving

Fr<1GHz - - 4 nW -

Fr≧1GHz

- - 20 nW -

PAGE

6/22

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

TSZ22111･05･002

PRODUCTS

11. TERMINAL FUNCTIONS

Back side

TYPE

HYBRID IC

BP3595

BP3595 Connector (Receptacle) Type

：DF40C-30DS-0.4V(51) (Hirose electric Co., Ltd.)

User-side Connector (Plug) Type

PAGE

7/22

：DF40C-30DP-0.4V(51) (Hirose electric Co., Ltd.)

Table 1. Module Terminal Functions

No.

TERMINAL

NAME

I/O FUNCTIONS REMARKS

1 BOOT_SEL0 I(*) Boot mode select (**) 2 GPIO8/32k I/O General purpose Input/Output 8 GPIO 8 or 32.768kHz clock input 3 GPIO6 I/O General purpose Input/Output 6 4 GPIO0 I/O General purpose Input/Output 0 5 V28_STBY I V28 LDO Stand-by port Active Hi (VCC Voltage) 6 GPIO2 I/O General purpose Input/Output 2 7 GPIO1 I/O General purpose Input/Output 1 8 V12_STBY I V12 LDO Stand-by port Active Hi (VCC Voltage)

9 UART_TXD O UART sending data 10 UART_RXD I UART receiving data 11 FLASH_TXD I/O Flash memory sending data Terminal for flash boot 12 FLASH_CLK O Flash memory clock Terminal for flash boot 13 FLASH_CSB O Flash memory chip select Terminal for flash boot 14 FLASH_RXD I Flash memory receiving data Terminal for flash boot 15 PRST I Power on reset 0:Reset, 1:Normal 16 GND - Ground 17 USB_DM AI/O USB data minus 18 USB_DP AI/O USB data plus 19 GND - Ground 20 SDDATA2 I/O SDIO data 2 21 SDDATA3 I/O SDIO data 3 22 SDCMD I/O SDIO command 23 VCC - Power supply 3.3V Module power supply input 24 VCC - Power supply 3.3V Module power supply input 25 SDCLK I SDIO clock 26 SDDATA0 I/O SDIO data 0 27 SDDATA1 I/O SDIO data 1 28 HOST_SEL I(*) Host I/F select 0:USB, 1:SDIO 29 FLASH_SEL I(*) Flash memory area select 0:region1, 1:region2 30 BOOT_SEL1 I(*) Boot mode select (**)

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

(*) FLASH_SEL/HOST_SEL/BOOT_SEL0/BOOT_SEL1 terminal hold the value after reset (Power On Reset). After reset, these terminals are used for another purpose in the module.

They have pull down resistance inside. Therefore, please set these terminals OPEN in case of setting for “0” and Pull up 3.3V (power supply voltage) with 3kΩ～5kΩ resistor (recommendation is 4.7kΩ resistor) in case of setting for “1”. When the host MCU controls these terminal, please do not connect directly with output terminal of host MCU and insert 3kΩ～5kΩ resistor (recommendation is 4.7kΩ resistor) between them.

When FLASH BOOT function is not used, FLASH_TXD terminal (pin 11) should be connected pull down resistor of 47kΩ.

When FLASH BOOT function is used, FLASH_TXD terminal (pin 11) and FLASH_RXD (pin 14) terminal would

be connected pull down resistor, if you need.

PRST is POWER ON RESET terminal. It is connected 4.7kΩ resistor + 2.2uF capacitor at 3.3V inside the module. In case that need to watch the power supply voltage, please connect such as OPEN DRAIN RESET IC for this terminal.

V12_STBY terminal and V28_STBY terminal control LDO which are mounted BP3595. Hi(VCC voltage): active, Lo(GND):stand-by

Please open the other unused terminals.

(**) BOOT_SEL terminals select the interface to boot the firmware.. BOOT_SEL[1:0] 00:USB, 01:SDIO, 10:FLASH, 11:UART

HYBRID IC

TYPE

BP3595

PAGE

8/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

12. DIMENSIONS

PRODUCTS

HYBRID IC

TYPE

BP3595

PAGE

9/22

Fig.2 Dimensions（Unit: mm）

13. MARKING SPECIFICATION

123*

▲▲▲

Marking 123*: Production lot number (3 digits + 1 internal serial number) （Example）123→Year 2011 Week 23th

Fig.3 Marking specification（Back side）

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

HYBRID IC

14. PRECAUTIONS FOR MOUNTING

Pattern

Antenna

TYPE

PAGE

BP3595

Pattern Prohibition Area Screw Hole (M2)

Connector

10/22

Shield Case

Fig.4 Precautions for Mounting (Unit：mm)

(1) Please don’t patterning the area under “pattern prohibition area” so that there is an adverse effect in a

wireless characteristic. (2) Please do not set your substrates and chassis around the chip antenna within 1cm. (3) Please do not use metals as the material of the chassis. (4) Please do not mount parts under this module except a specified connector.

ABOUT THE FIXATION OF THIS MODULE

Please use the M2 screw (made of metal) for fixing BP3595.

M2 screw hole is GND potential of this module, please use the metal spacer of 1.5mm height, between your

substrate and this module.

A torque to tighten M2 screw should be more than 1kgf･cm, and do not tighten the screw too much.

Pattern antenna

M2 screw

BP3595

Spacer

TSZ22111･05･002

REV.B

Nut

Fig.5 Fixed Module Figure (Side view)

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

User side PCB

PRODUCTS

HYBRID IC

TYPE

15. PRODUCT LABEL SPEC

The label shown in the following figure is put on the shield case.

BP3595

PAGE

11/22

Fig.6 Product Label Spec

*Micro QR code is included in the MAC address information.

(Note)The design of product label might change without previous notice.

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

16. REFERENCE CIRCUIT

16.1 USB

HOST INTERFACE

HYBRID IC

TYPE

BP3595

PAGE

12/22

Fig.7

*About USB_DP and USB_DM Lines

・ Please shorten wiring as much as possible. ・ Please take the differential impedance matching to 90Ω±10%. ・ Please set up to 45Ω±10% for impedance matching of single end. ・ Please wire USB_DP and USB_DM lines as same lengths.

(Difference of the wire length is less than 0.5mm.)

・ Please do not bend USB lines many times and make the bend angle small. ・ Please do not make threw hole in wiring. ・ Please do not cross the USB lines and another signal lines. ・ Please do not cross the USB lines and power supply lines.

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp)

USB Interface Reference Circuit

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

16.2 SDIO HOST INTERFACE

PRODUCTS

HYBRID IC

TYPE

BP3595

PAGE

13/22

Fig.8 SDIO Interface Reference Circuit

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp)

*About the line of SDCLK/SDDATA/SDCMD

・Over shoot and under shoot of signal lines cause a lot of damage to wireless performance.

Please design your product lower noise levels within the SDIO standard timing. For example it can be insert dumping resistors near the host signal source.

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

16.3 UART INTERFACE

PRODUCTS

HYBRID IC

TYPE

BP3595

PAGE

14/22

Fig.9 UART Interface Reference Circuit

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp)

REV.B

TSZ22111･05･002

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

HYBRID IC

16.4

FLASH BOOT (UART INTERFACE MODE)

TYPE

BP3595

PAGE

15/22

LE25U40CQH-AH (Sanyo Semiconductor)

W25X40CLZPIG (Winbond)

16.5 Reset IC

Fig.10 Flash Boot (UART INTERFACE )Reference Circuit

TSZ22111･05･002

(ROHM)

Fig.11 Reset IC Connection Reference Circuit

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

④

PRODUCTS

HYBRID IC

TYPE

BP3595

17. PACKING SPEC

17.1 Packing Method

In principle, 25 pieces of modules should be packaged in the packaging tray, and it should be piled up 12 steps to make 300 pieces, and with an empty pack on the top. The number of piling might change according to the quantity of delivery without previous notice.

Tray

Fixed by adhesive cellophane tape.

(4 places)

Fixed by adhesive cellophane tape.

(3 places)

Packing case

PAGE

16/22

Fig.12 Packing Method

17.2 Label indication

The label with following things is stuck at the packing case.

① Type name（BP3595） ② Quantity ③ Lot No. ④ Shipment inspection stamp ⑤ Country of origin ⑥ Manufacturing company name（Trade mark） ⑦ Logotype of lead free

Please refer to the following example of the label indication.

①

②

⑤

CHINA

⑥

③

④

Fig.13 Label Indication

S.MIZUHAR

⑦

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

18. MANUFACTURING FACTORY

HYBRID IC

TYPE

BP3595

PAGE

17/22

ROHM APORO CO., LTD. (FUKUOKA, JAPAN) ROHM ELECTRICS DALIAN CO., LTD. (DALIAN, CHINA)

19. OPERATING PRECAUTIONS

1）There is some case that the MAC address does not become sequential number in a same packing. 2）About soldering of mounting parts on this product, presence of soldering fillet does not be asked. 3）About the products label, defections does not be asked except coming off, lapping, or not to recognize the

characters extremely.

4）A connector is possible to break by excessive swing or shock because of the structure of the product.

Efficient evaluation is necessary to use the module when there is a fear of swinging or shocking.

5）The connector of BP3595 does not have a specification assumed to do many times of extraction and insertion.

Please be sure that the number of extraction and insertion is within 10 times.

20. PRECAUTIONS AS RESET OPERATION

･Please do not reset (PRST, COMMAND RESET) when BP3595 is accessing to its internal EEPROM. ･BP3595 under writing to the EEPROM is reset (*), which may cause unexpected failure such as incorrect

checksum.

･BP3595 under reading from the EEPROM is reset (**), which may cause unstable condition, and you should

supply VCC power again.

(*) About write operations of the EEPROM BP3595 writes to the EEPROM in the following cases.

①Recording various settings used in TCP/IP firmware ②Recording credential data which is obtained when BP3595 with stand-alone mode acts WPS

(**) About read operations of the EEPPROM

BP3595 reads from the EEPROM in the following cases.

①After reset (≦100ms) ②After firmware starting (≦100ms) ③When WID_SERIAL_NUMBER command is issued.

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

HYBRID IC

TYPE

PAGE

BP3595

21. PRECAUTIONS AS A WIRELESS EQUIPMENT 1

BP3595 acquired “Construction design attestation” (Article 38-24, Clause1 of Radio Law in Japan) of “Particular wireless equipment: Low power data communications system in the 2.4GHz band, which is a Wireless equipment in Article 2-1(19)” Therefore, only in Japan, it is possible to use as wireless equipment without applying for wireless office.

・Construction design attestation No. : 003-120319

Be sure to keep following notes to use the module safely as wireless equipment.

1）The label on the module is a certification which shows it has “Certification of technical standard conformity.”

Please do not remove the label or do not put another label on the label.

2）Please do not resolve or remodel strictly because there are some cases of receiving penalty based on Radio Law

in Japan.

22. PRECAUTIONS AS A WIRELESS EQUIPMENT 2

BP3595 acquired radio law certified in U.S.A (Federal Communications Commission Part15 Subpart C). BP3595 is able to use in U.S.A without application of FCC.

・ FCC ID: ANSBP3595

Please following the below precautions for using BP3595 as wireless equipment in U.S.A.

1) The label on the product is a certification label shown to be acquiring "FCC certification".

Please do not put another label on the label.

2) If FCC ID is displayed on BP3595 cannot be seen from the outside of your product, the following

displays (*) are needed for your product including BP3595.

“Contains Transmitter Module FCC ID: ANSBP3595”

“Contains FCC ID: ANSBP3595”

(*) The character size can be read easily is required. However it is not required more than 8 points. And also line break is not permit.

3) It is necessary to display the following texts on your product. (*)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(*) If the text cannot be displayed on your product, you should describe in a manual or a package. It is foundations that the text is indicated on your product.

18/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

4) It is necessary to indicate all the texts applicable to the manual of your product.

① It is necessary text for all products.

FCC CAUTION Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

② It is necessary text for all products . 2

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

③ It is necessary text for mobile product or portable product.

A SAR examination is not required at mobile products (*) but is required at portable products (**).

(*) Mobile product ･･･ The product is used separating from a human body over 20 cm. (**) Portable product ･･･ The product is used by human body within 20cm.

③-1 It is necessary texts for a mobile product that is not required SAR examination if it is used by human body

within 20cm.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). [※But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body.]

③-2 It is necessary texts for a mobile product that is required SAR examination if it is used by human body

within 20cm.

（※）It is necessary text for the product which is examined Hand SAR or uses always in hand but lower than limit of Hand SAR.

“excluding extremities: hands, wrists, feet and ankles”

③-3 It is necessary texts for a portable product that is not required SAR examination.

HYBRID IC

TYPE

BP3595

PAGE

19/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

③-4 It is necessary texts for a portable product that is required SAR examination.

The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. [product name (model name)] has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.

23. PRECAUTIONS AS A WIRELESS EQUIPMENT 2

HYBRID IC

TYPE

PAGE

BP3595

BP3595 acquired radio law certified in Canada (Industry Canada: IC). BP3595 is able to use in Canada without application of IC.

・IC：20579-BP3595

Please following the below precautions for using BP3595 as wireless equipment in Canada.

1) The label on the product is a certification label shown to be acquiring "IC certification". Please do not put another label on the label.

2) If IC number is displayed on BP3595 cannot be seen from the outside of your product, the following

displays (*) are needed for your product including BP3595.

“Contains Transmitter Module IC:20579-BP3595”

“Contains IC:20579-BP3595”

(*) The character size can be read easily is required. However it is not required more than 8 points.

3) It is necessary to indicate all the texts applicable to the manual of your product.

① It is necessary text for all products.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

(※)It is necessary to shown in English with French.

20/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

② It is necessary text for mobile product or portable product.

A SAR examination is not required at mobile products (*) but is required at portable products (**).

(*) Mobile product ･･･ The product is used separating from a human body over 20 cm. (**) Portable product ･･･ The product is used by human body within 20cm.

②-1 It is necessary texts for a mobile product that is not required SAR examination if it is used by human body

within 20cm.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). [※But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body.]

HYBRID IC

TYPE

BP3595

PAGE

21/22

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement

non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. [※Cependant, il est souhaitable qu'il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps.]

②-2 It is necessary texts for a mobile product that is required SAR examination if it is used by human body

within 20cm.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (※).

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (※).

（※）It is necessary text for the product which is examined Hand SAR or uses always in hand but lower than limit of Hand SAR.

English: ”excluding extremities: hands, wrists, feet and ankles” French: ”à l’exception des extrémités : mains, poignets, pieds et chevilles”

②-3 It is necessary texts for a portable product that is not required SAR examination.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption rate (SAR).

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation du débit d’absorption spécifique (DAS).

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

PRODUCTS

②-4 It is necessary texts for a portable product that is required SAR examination.

The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. [product name (model name)] has been tested and found to comply with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules.

Les connaissances scientifiques dont nous disposons n’ont mis en évidence aucun problème de santé associé à l’usage des appareils sans fil à faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil à faible puissance sont entièrement sans danger. Les appareils sans fil à faible puissance émettent une énergie radioélectrique (RF) très faible dans le spectre des micro-ondes lorsqu’ils sont utilisés. Alors qu’une dose élevée de RF peut avoir des effets sur la santé (en chauffant les tissus), l’exposition à de faibles RF qui ne produisent pas de chaleur n’a pas de mauvais effets connus sur la santé. De nombreuses études ont été menées sur les expositions aux RF faibles et n’ont découvert aucun effet biologique. Certaines études ont suggéré qu’il pouvait y avoir certains effets biologiques, mais ces résultats n’ont pas été confirmés par des recherches supplémentaires. [product name (model name)] a été testé et jugé conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC.

24. IMPORTANT NOTE BOTH FCC AND IC

In the event that some conditions cannot be met (for example co-location with another transmitter), then the FCC / IC authorization is no longer considered valid and the FCC / IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC / IC authorization. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.)

25. MANUAL INFORMATION TO THE END USER

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

26. ANTENNA RESTRICTION

The antenna is designed as permanent attached and no consideration of replacement.

HYBRID IC

TYPE

PAGE

BP3595

22/22

TSZ22111･05･002

REV.B

SPECIFICATION No.：BP3595-B-001-E(Lead Free)

ROHM BP3595 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual