®
R&S
RT-ZF1
USB 2.0 Compliance Test
Fixture Set
Manual
(=A[J2)
1317432602
Version 08
This manual describes the R&S RT-ZF1 USB 2.0 Compliance Test Fixture Set
(1317.3420.02).
© 2021 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: +49 89 41 29 - 0
Email: info@rohde-schwarz.com
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1317.4326.02 | Version 08 | R&S®RT-ZF1
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g.
R&S®RT-ZF1 is indicated as R&S RT-ZF1.
R&S®RT-ZF1
Safety Information
1 Safety Information
The product documentation helps you to use the product safely and efficiently.
Keep the product documentation nearby and offer it to other users.
Safety information warns you about the potential dangers and gives instructions
how to prevent personal injuries or damage caused by dangerous situations.
Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.
Intended use
The equipment under test (EUT) is a signal quality test and development board,
indented to be used at laboratory or test and measurement areas. These areas
are used for analysis, testing and servicing and where equipment is operated by
trained personnel (EN 61326-1, 3.9).
Operating site
Only use the product indoors, and keep it dry. The product has no casing and is
sensitive to moisture and humidity.
The product is suitable for pollution degree 2 environments where nonconductive
contamination can occur. For more information on environmental conditions such
as ambient temperature, see the specifications.
Safety instructions
Connect only USB interfaces to the boards.
Hot surface. The load board gets hot during testing. Do not touch. Risk of
skin burns. Risk of fire.
Electromagnetic emissions
The EUT is considered as a test probe, EN 61326-2-1, clause 5.2.4.101, note 1.
Therefore normal operation may increase emissions and/or reduce immunity in
certain applications.
Operation in type 3 (controlled) electromagnetic environments EN 61326-1, table
3 is recommended.
The EUT is an EN 55011 class A equipment. Class A equipment is intended for
use in an industrial environment. There may be potential difficulties in ensuring
3Manual 1317.4326.02 ─ 08
R&S®RT-ZF1
electromagnetic compatibility in other environments due to conducted as well as
radiated disturbances.
ESD and EMI impact
The product is sensitive to electrostatic discharge (ESD) because of open modules. Protect the work area against electrostatic discharge to avoid damage to
electronic components. Always work at a static-approved workstation.
Electromagnetic interference (EMI) can affect the measurement results. To avoid
any impact, use only USB cables shorter 3 m.
Disposal
In line with EN 50419, the product cannot be disposed of in the normal
household waste. Even disposal via the municipal collection points for
waste electrical and electronic equipment is not permitted.
Product Description
Deliveries
Rohde & Schwarz has developed a disposal concept for the ecofriendly disposal
or recycling of waste material. Rohde & Schwarz fully assumes its obligation as a
producer to take back and dispose of electrical and electronic waste. Contact
your local service representative to dispose of the product.
2 Product Description
The R&S RT-ZF1 USB 2.0 compliance test fixture set is a product for automatic
testing of USB 2.0 compliance (high-speed) as well as USB 1.1 (full-speed) and
USB 1.0 (low-speed). It is used in combination with the R&S RTO/R&S RTP oscilloscopes, with the R&S RTO/RTO6/RTP-K21 USB 2.0 compliance test option
(1317.4103.02)/(1337.8685.02) and the R&S ScopeSuite software.
For data, see the "R&S RT-ZFxx Oscilloscope Test Fixtures - Specifications" at
www.rohde-schwarz.com/brochure-datasheet/rto.
2.1 Deliveries
The R&S RT-ZF1 comprises two test boards and accessories:
●
Load board (1317.5300.02)
4Manual 1317.4326.02 ─ 08
Loading...