Rohde&Schwarz R&S®RTC1000 Getting Started Getting started

®

R&S

RTC1000
Digital Oscilloscope
Getting Started

(=S×^2)

1335734602
Version 06

This manual describes the following R&S®RTC1000 models:

●

R&S®RTC1002 (1335.7500K02)

© 2021 Rohde & Schwarz GmbH & Co. KG

Mühldorfstr. 15, 81671 München, Germany

Phone: [phone] - 0

Email: [e-mail]

Internet: www.rohde-schwarz.com

Subject to change – data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

1335.7346.02 | Version 06 | R&S®RTC1000

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g.
R&S®RTC1000 is indicated as R&S RTC1000.

R&S®RTC1000

Contents

1 Safety Information................................................................. 5

1.1 Safety Instructions................................................................................5

1.2 Korea Certification Class A..................................................................6

2 Documentation Overview......................................................7

2.1 Manuals and Instrument Help..............................................................7

2.2 Data Sheet and Brochure..................................................................... 8

2.3 Calibration Certificate...........................................................................8

2.4 Release Notes, Open Source Acknowledgment................................ 8

Contents

3 Preparing for Use...................................................................9

3.1 Unpacking and Checking the Instrument........................................... 9

3.2 Positioning the Instrument................................................................ 10

3.3 Starting the Instrument.......................................................................11

3.3.1 Powering On..........................................................................................11

3.3.2 Starting Up and Shutting Down.............................................................12

3.3.3 Powering Off......................................................................................... 13

3.3.4 EMI Suppression...................................................................................13

3.4 Replacing the Fuse............................................................................. 13

4 Instrument Tour................................................................... 15

4.1 Front Panel.......................................................................................... 15

4.1.1 Input Connectors...................................................................................16

4.1.2 Other Connectors on the Front Panel................................................... 17

4.2 Rear Panel........................................................................................... 18

5 Contacting Customer Support........................................... 21

3Getting Started 1335.7346.02 ─ 06

R&S®RTC1000

Contents

4Getting Started 1335.7346.02 ─ 06

R&S®RTC1000

Safety Information

Safety Instructions

1 Safety Information

The R&S RTC1000 digital oscilloscope is designed for measurements on circuits
that are only indirectly connected to the mains or not connected at all. It is not
rated for any measurement category.

The instrument is rated for pollution degree 2 - for indoor, dry location use where
only non-conductive pollution occurs. Temporary conductivity caused by conden­sation is possible.

The instrument must be controlled by personnel familiar with the potential risks of
measuring electrical quantities. Observe applicable local or national safety regula­tions and rules for the prevention of accidents.

Safety information is part of the product documentation. It warns you about the
potential dangers and gives instructions how to prevent personal injury or dam­age caused by dangerous situations. Safety information is provided as follows:

●

The "Basic Safety Instructions" in different languages are delivered as a prin­ted brochure with the instrument.

●

Throughout the documentation, safety instructions are provided when you
need to take care during setup or operation.

1.1 Safety Instructions

To prevent electric shock, personal injury or fire, follow these rules:

●

Do not open the instrument casing.

●

Do not use the instrument if you detect or suspect any damage of the instru­ment or accessories.

●

Do not operate the instrument in wet, damp or explosive atmospheres.

●

Make sure that the instrument is properly grounded.

●

Do not use the instrument to ascertain volt-free state.

●

Do not exceed the voltage limits given in Chapter 4.1.1, "Input Connectors",
on page 16.

5Getting Started 1335.7346.02 ─ 06

R&S®RTC1000

Korea Certification Class A

An unsuitable operating site or test setup can damage the instrument and con­nected devices. Ensure the following operating conditions before you switch on
the instrument:

●

Read and observe the "Basic Safety Instructions" brochure and the safety
instructions in the manuals.

●

Observe the operating conditions specified in the data sheet. Note that the
general safety instructions also contain information on operating conditions.

●

Position the instrument as described in the following sections.
Make sure that all fan openings are unobstructed and the airflow perforations
are unimpeded. The minimum distance from the wall is 10 cm.

●

Signal levels at the input connectors are all within the specified ranges.

●

Signal outputs are correctly connected and are not overloaded.

Safety Information

1.2 Korea Certification Class A

이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하
시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.

6Getting Started 1335.7346.02 ─ 06

R&S®RTC1000

Documentation Overview

Manuals and Instrument Help

2 Documentation Overview

This section provides an overview of the R&S RTC1000 user documentation.

2.1 Manuals and Instrument Help

You find the manuals on the product page at:

www.rohde-schwarz.com/manual/rtc1000

Getting started manual

Introduces the R&S RTC1000 and describes how to set up the product. A printed
English version is included in the delivery.

User manual

Contains the description of all instrument modes and functions. It also provides
an introduction to remote control, a complete description of the remote control
commands with programming examples, and information on maintenance and
instrument interfaces. Includes the contents of the getting started manual.

The online version of the user manual provides the complete contents for immedi­ate display on the internet.

Instrument help

The help offers quick, context-sensitive access to the functional description
directly on the instrument.

Basic safety instructions

Contains safety instructions, operating conditions and further important informa­tion. The printed document is delivered with the instrument.

Instrument security procedures manual

Deals with security issues when working with the R&S RTC1000 in secure areas.

7Getting Started 1335.7346.02 ─ 06