DC Power Supply and
Battery Operation
R&S FSV-B30/-B32/-B34
Installation Manual
(=EWU2)
1321393702
Version 02
This installation manual describes the following functions and options:
●
DC Power Supply (R&S FSV-B30, Order no. 1329.0243.02)
●
Li-Ion Battey Pack (R&S FSV-B32, Order no. 1321.3750.04)
●
Battery Charger (R&S FSV-B34, Order no. 1321.3950.02)
© 2021 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: +49 89 41 29 - 0
Email: info@rohde-schwarz.com
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1321.3937.02 | Version 02 | DC Power Supply and Battery Operation
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g.
R&S®FSV is indicated as R&S FSV.
DC Power Supply and Battery Operation
Safety Instructions for Lithium
Batteries
1 Safety Instructions for Lithium Batteries
The product contains exchangeable or built-in lithium polymer or lithium ion cells
or batteries. The use of the word battery in the following always means all types.
Only the battery contents are potentially hazardous. As long as a battery is
undamaged and the seals remain intact, there is no danger.
Impact, shock or heat can cause damage such as dents, punctures and other
deformations. A damaged battery poses a risk of personal injury. Handle a damaged or leaking battery with extreme care. Immediately ventilate the area since
the battery releases harmful gases. If you come into contact with the battery fluid,
immediately remove all contaminated clothing. Irritation can occur if the battery
fluid comes in contact with your skin or eyes. Immediately and thoroughly rinse
your skin or eyes with water and seek medical aid.
For safe handling, follow these rules:
●
Do not short-circuit the battery.
●
Do not mechanically damage the battery. Do not open or disassemble the battery.
●
Do not expose the battery to high temperatures such as open flames, hot surfaces and sunlight.
●
Only use the battery with the designated Rohde & Schwarz product.
●
Only use the appropriate Rohde & Schwarz charger to charge the batteries. If
the batteries are improperly charged, there is a risk of explosion. For charging
and discharging temperature ranges, see the product documentation.
●
Replace exchangeable batteries only with the same battery type.
●
Store the battery in the product or use the product packaging.
●
Dispose of exchangeable batteries separately from normal household waste
as specified by the local waste disposal agency.
If you disregard these rules, you risk serious personal injury or even death due to
explosion, fire or hazardous chemical substances. The product documentation
provides further details.
If exchangeable batteries or products with built-in batteries are defective, contact
the Rohde & Schwarz customer service. Rohde & Schwarz classifies the severity
of the defect. When returning batteries or Rohde & Schwarz products containing
batteries, use a carrier qualified to transport dangerous goods and notify the carrier of this classification. Follow the carrier’s transport stipulations in line with
IATA-DGR, IMDG-Code, ADR or RID.
3Installation Manual 1321.3937.02 ─ 02
DC power supplyDC Power Supply and Battery Operation
Installing the DC power supply
Figure 1-1: Disposal information in line with EU battery directive
2 DC power supply
Using the DC power supply (option R&S FSV‑B30), the instrument can be operated with a DC voltage of 10 V to 28 V. The voltage source can have a current of
25 A to 12.5 A.
If you use an external power supply unit to supply safety extra-low DC voltage
(SELV) to the instrument, be sure to meet the requirements for reinforced/double
insulation in accordance with DIN/EN/IEC 61010 (UL 3111, CSA C22.2 No.
1010.1) or DIN/EN/IEC 60950 (UL 1950, CSA C22.2 No. 950). Provide current
limitation in accordance with DIN EN 61010-1 Appendix F2.1. Use a cable no longer than 3 m.
2.1 Installing the DC power supply
The DC power supply is attached to the rear panel of the instrument.
To install the DC power supply on the instrument
Installing the DC power supply requires technically trained personnel.
1. Disconnect the DC power supply from the voltage source to avoid long-term
damage to the device.
2. Disconnect the power cable from the instrument.
3. Only for instruments with B1 option (ruggedized housing):
4Installation Manual 1321.3937.02 ─ 02
Loading...