Spectrum Analyzer ¸FSL
Specifications
Version
02.00
August
2005
Specifications
Specifications
Specifications apply under the following conditions:
15 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to.
Data without tolerances: typical values only. Data designated 'nominal' applies to design parameters and is not tested.
Frequency
Frequency range
R&S FSL6 9 kHz to 6 GHz
Frequency resolution
Reference frequency, internal, nominal
Aging per year 1 × 10
Temperature drift 0 °C to +50 °C 1 × 10–6
Reference frequency, internal, nominal R&S FSL-B4 OCXO reference frequency
Aging per year 1 × 10–7
Temperature drift 0 °C to +50 °C 1 × 10–7
Frequency readout
Marker resolution span/500
Uncertainty ±(marker frequency × reference
Frequency counter resolution 1 Hz
Count uncertainty S/N >25 dB ±(frequency × reference uncertainty +
Frequency span 0 Hz, 10 Hz to 3 GHz/6 GHz
Span uncertainty 3%
Spectral purity
SSB phase noise
Carrier offset 1 kHz typ. –95 dBc(1 Hz)
10 kHz <–98 dBc(1 Hz), typ. –103 dBc(1 Hz)
100 kHz <–98 dBc(1 Hz), typ. –105 dBc(1 Hz)
1 MHz <–115 dBc(1 Hz), typ. –120 dBc(1 Hz)
R&S FSL3 9 kHz to 3 GHz
1 Hz
–6
option
with marker or frequency counter
uncertainty + 2% × span +10% ×
resolution bandwidth + ½ (last digit))
½ (last digit))
f = 500 MHz
Sweep time
Sweep time
Uncertainty nom. 3%
Span 0 Hz 1 µs to 16000 s in 5% steps
10 Hz ≤ span ≤ 1.5 GHz
1.5 GHz < span ≤ 3 GHz
span > 3 GHz
2.5 ms to 16000 s
5 ms to 16000 s
10 ms to 16000 s
2 Spectrum Analyzer R&S FSL Version 02.00, July 2005
Resolution bandwidths
Sweep filters
Resolution bandwidths 300 Hz to 10 MHz (–3 dB) in 1/3
option R&S FSL-B7 10 Hz to 10 MHz (–3 dB) in 1/3 sequence
Resolution bandwidth uncertainty nom. <3%
Resolution filter shape factor 60:3 dB nom. <5 (Gaussian type filters)
FFT filters
3 dB bandwidths 300 Hz to 30 kHz in 1/3 sequence
option R&S FSL-B7 1 Hz to 30 kHz in 1/3 sequence
Bandwidth uncertainty nom. 5%
Shape factor 60 dB : 3 dB nom. 2.5
Channel filters
Bandwidths 300; 500 Hz;
option R&S FSL-B7 100 Hz, 200 Hz additionally
Video bandwidths (1-pole low pass RC filters) 1 Hz to 10 MHz in 1/3 sequence
Demodulation bandwidth nom. 20 MHz
analyzer mode
1; 1.5; 2; 2.4; 2.7; 3; 3.4; 4; 4.5; 5; 6; 8.5; 9 kHz
10; 12.5; 14; 15; 16; 18 (RRC); 20; 21; 24.3 (RRC); 25; 30; 50; 100; 150; 192; 200; 300;
500 kHz
1; 1.228; 1.28 (RRC); 1.5; 2; 3;3.84 (RRC); 4.096 (RRC); 5 MHz
(RRC = root raised cosine)
sequence
Level
Display range displayed noise floor to +20 dBm
Maximum rated input level
DC voltage 50 V
CW RF power 30 dBm (= 1 W)
Peak RF power 36 dBm (= 2 W) < 3 s
Max. pulse voltage 150 V
Max. pulse energy 10 µs 10 mWs
1 dB compression of input mixer 0 dB RF attenuation, f > 200 MHz nom. +5 dBm
Intermodulation
Third-order intermodulation intermodulation-free dynamic range,
level 2 × –20 dBm, reference level
–10 dBm
f < 30 MHz
f ≥ 30 MHz
Second harmonic intercept (SHI) f = 20 MHz to 3 GHz typ. 40 dBm
Displayed average noise level
frequency preamplifier = off
9 kHz to 1 MHz
frequency preamplifier = on
9 kHz to 1 MHz
0 dB RF attenuation, RBW = 1 kHz,
VBW = 10 Hz, normalized to 1 Hz
1 MHz to 10 MHz
10 MHz to 50 MHz
50 MHz to 3 GHz
3 GHz to 5 GHz
5 GHz to 6 GHz
1 MHz to 10 MHz
10 MHz to 50 MHz
50 MHz to 3 GHz
3 GHz to 5 GHz
5 GHz to 6 GHz
typ. 60 dBc
>60 dBc (IP3 + 10 dBm), typ. 70 dBc
<–100 dBm(1Hz)
<–115 dBm(1Hz)
<–130 dBm(1Hz)
<–140 dBm(1Hz)
<–136 dBm(1Hz)
<–130 dBm(1Hz)
<–115 dBm(1Hz)
<–130 dBm(1Hz)
<–145 dBm(1Hz)
<–152 dBm(1Hz)
<–146 dBm(1Hz)
<–140 dBm(1Hz)
Version 02.00, July 2005 Spectrum Analyzer R&S FSL 3
Immunity to interference
Image frequency f + 2 × 48.375 MHz
f + 2 × 838.375 MHz
f + 2 × 7158.375 MHz
Intermediate frequency 48.375 MHz, 838.375 MHz,
7158.375 MHz
Spurious response, inherent f > 30 MHz, without input signal,
RF attenuation = 0 dB, RBW < 1 MHz
>60 dB, typ. –80 dB
>60 dB, typ. –80 dB
typ. –60 dB
>60 dB, typ. –80 dB
<–90 dBm
Spurious response related to local oscillators <–60 dBc
Spurious response related to A/D conversion typ. <–70 dBc
Spurious response related to sub harmonic of first LO
)
in
Spurious response
at mixer level <–10 dBm
(Spur at 7158.375 MHz – 2 × f
related to harmonic of first LO
(spur at f
– 3579.1875 MHz)
in
typ. 60 dBc
typ. <–60 dBc
Level display
Logarithmic level axis 10 dB to 100 dB
Linear level axis 0 % to 100 %/10 divisions
Number of traces 4
Trace detectors max peak, min peak, auto peak, sample,
RMS, quasi peak, average
Number of measurement points default value
range
501
125 to 32001
in steps of about a factor of 2
Trace functions clear/write, max hold, average, min hold,
view
Setting range of reference level logarithmic level display –80 dBm to 20 dBm
in steps of 2 dB, 5 dB or 10 dB
linear level display –80 dBm to 20 dBm, 0 % to 100 %
Units of level axis logarithmic level display dBm, dBmV, dBµV, dBµA, dBpW
linear level display µV, mV, V, µA, mA, A, pW, nW, µW, mW,
W
Level measurement uncertainty
95% confidence level, 20 °C to 30 °C,
S/N>16 dB, 0 dB to –50 dB from
reference level
Absolute uncertainty at reference
10 MHz < f ≤ 3 GHz
3 GHz < f ≤ 6 GHz
<0.5 dB
<0.8 dB
<0.3 dB
frequency
Frequency response (20 °C to 30 °C) f ≤ 3 GHz
3 GHz < f ≤ 6 GHz
<0.5 dB
<0.8 dB
Attenuator uncertainty <0.3 dB
Uncertainty of reference level setting <0.1 dB (nom.)
Display nonlinearity
Logarithmic level display S/N>16 dB
0 dB to –50 dB
<0.2 dB
Bandwidth switching uncertainty reference: RBW = 10 kHz <0.1 dB (nom.)
Trigger functions
Trigger
Trigger source free run, video, external, IF power
External trigger level TTL level
4 Spectrum Analyzer R&S FSL Version 02.00, July 2005
Inputs and outputs
RF input
Impedance 50 Ω
Connector N female
VSWR f ≤ 3 GHz
3 GHz < f ≤ 6 GHz
Input attenuator 0 dB to 30 dB in 5 dB steps
AF output
Connector 3.5 mm mini jack
Output impedance <100 Ω
Open-circuit voltage up to 1.5 V, adjustable
Tracking generator
Tracking generator models 13 and 16 only N female, 50 Ω
Output level –20 dBm to 0 dBm in 1 dB steps
Frequency range 1 MHz to 3 GHz/6 GHz
Reverse power
DC voltage
CW RF power
Max. pulse voltage
Max. pulse energy (10 µs)
External reference
Connector BNC female, 50 Ω
Input level 0 dBm to +10 dBm
Output level with R&S FSL-B4 typ. 0 dBm
Frequency 10 MHz ± 5 ppm
External trigger/gate input
Connector BNC female, 50 Ω
Input level TTL compatible
Probe power
+15 V DC, –12.6 V DC and ground,
typ. <1.2
typ. <1.5
50 V
30 dBm (= 1 W)
150 V
10 mWs
max. 150 mA, nominal
Version 02.00, July 2005 Spectrum Analyzer R&S FSL 5
General specifications
Remote control
LAN interface 10/100 BaseT, RJ-45
IEC/IEEE bus (GPIB) R&S FSL-B10 SCPI 1997.0
Display
Resolution 640 × 480 pixels
Pixel failure rate <2 × 10–5
Mass memory
Mass memory Flash disk (internal), USB memory stick
Data storage
Temperature
Temperature operating temperature range
Climatic loading +25 °C/+40 °C at 95% relative humidity
Mechanical resistance
sinusoidal vibration IEC 60068-2-6
random vibration IEC 60068-2-64
shock 40 g shock spectrum,
Power supply
Input voltage range, AC, nominal 100 V to 240 V
AC supply frequency 50 Hz to 400 Hz
Input current, AC 0.9 A to 0.3 A
Input voltage range, DC, nominal 10 V to 28 V
Input current, DC 8.0 A to 2.2 A
Power consumption typ. 45 W, max. 65 W with all options
Safety IEC 61010-1, EN 61010-1, UL 61010B-1,
EMC meets CISPR 11/EN 55011 group 1
Dimensions
Weight without options
permissible temperature range
storage temperature range
W × H × D in mm
with handle
without handle
with battery pack
(not supplied)
>500 instrument settings and traces
+0 °C to +50 °C
+0 °C to +55 °C
–40 °C to +70 °C
(IEC 60068-2-30)
meets MIL-STD-810E, method 516.4
procedure 1, IEC 60068-2-27
CSA C22.2 No. 1010-1
class B;
meets IEC/EN 61326,
emission: class B
(residential environment)
immunity: industrial environment
(excluding operating frequency)
408.8 mm × 158.1 mm × 465.3 mm
342.3 mm × 158.1 mm × 367.0 mm
<7 kg
<8 kg
6 Spectrum Analyzer R&S FSL Version 02.00, July 2005
Additional Interfaces R&S FSL-B5
User port
Connector 9-pin D-Sub male
Output TTL compatible, 0 V/5 V max. 15 mA
Input TTL compatible, max. 5 V
Noise source control
Connector BNC female
Output 0 V/28 V, max. 100 mA, switchable,
IF/video out
Connector BNC female, 50 Ω
Bandwidth IF and video out typ. 20 MHz
Output level video out typ. 200 mV full scale (open circuit), linear
IF frequency IF out typ. 18 MHz
Power sensor
Connector 6-pin LEMOSA female for supported
supply for noise source
scaling
Power Sensors R&S NRP-Zxx
Version 02.00, July 2005 Spectrum Analyzer R&S FSL 7
AM/FM/ϕM Measurement Demodulator R&S FSL-K7
Measurement of analog modulation signals
Demodulation bandwidth 100 Hz to 6.4 kHz, binary steps
Recording length maximum 512 ksample
Recording time demodulation bandwidth
Display
AF (modulation frequency)
Range
Resolution 5 digits
Measurement uncertainty 0.1 %
AF filters
Lowpass 3 kHz, 15 kHz, 150 kHz,
Highpass 50 Hz, 300 Hz
Deemphasis 25 µs, 50 µs, 75 µs, 750 µs
AM demodulation
Measurement range modulation depth 0 % to 100 %
Modulation depth uncertainty
Residual AM
Distortion
FM rejection
FM demodulation
Measurement range frequency deviation
Deviation uncertainty
Residual FM
Distortion
AM rejection
100 Hz
6.4 kHz
12.5 kHz
1.6 MHz
3 MHz
5 MHz
8 MHz
10 MHz
18 MHz
frequency versus time (FM), amplitude versus time (AM), phase versus time (ϕM),
RF power versus time, RF spectrum (FFT), AF spectrum (FFT),
table with numeric values for: modulation deviation (peak, RMS), modulation
frequency, carrier offset, carrier power (power of unmodulated carrier), THD, SINAD
AF ≤ 1 MHz
demodulation bandwidth ≤ 200 kHz, RMS,
RF ≤ 3 GHz
RF input level ≥ (RF attenuation/dB –30)
dBm
10 Hz ≤ AF ≤ 100 kHz
AF ≤ 1 MHz and
AF + deviation ≤ 0.5 × demodulation
bandwidth
AF ≤ 1 MHz and
AF + deviation ≤ 0.5 × demodulation
bandwidth
demodulation bandwidth ≤ 100 kHz, RMS,
RF input level ≥ (RF attenuation/dB –30)
dBm
RF ≤ 1 GHz
RF = 3 GHz
10 Hz ≤ AF ≤ 100 kHz,
deviation < 400 kHz
100 Hz ≤ AF ≤ 1 kHz,
modulation depth 50 %
12.5 kHz to 1.6 MHz, binary steps
3 MHz, 5 MHz, 8 MHz, 10 MHz, 18 MHz
3276.8 s
51.2 s
26.6 s
200 ms
100 ms
50 ms
25 ms
12.5 ms
12.5 ms
≤5 MHz
max. 0.5 × demodulation bandwidth
5 %, 10 %, 25 % of demodulation
bandwidth
<3 % of reading + residual AM
0.2 %
0.3 %
typ. 1 % + residual AM
≤5 MHz
<3 % of reading + residual FM
150 Hz
200 Hz
0.3 %
30 Hz
8 Spectrum Analyzer R&S FSL Version 02.00, July 2005
ϕM demodulation
AF
Measurement range phase deviation <1000 rad
Residual ϕM demodulation bandwidth ≤ 100 kHz, RMS,
RF = 1 GHz, highpass 300 Hz,
RF input level ≥ (RF attenuation /dB
–30 dBm
Carrier power versus time
Display range noise floor to +20 dBm
Measurement uncertainty unmodulated carrier, S/N > 16 dB,
RF: 50 kHz to 3 GHz
Max. dynamic range demodulation bandwidth 200 kHz typ. 75 dB
Display linearity S/N >16 dB typ. 0.2 dB
AF spectrum
Span
Resolution bandwidth 1 Hz to 10 MHz
RF spectrum
Span
Resolution bandwidth 1 Hz to 10 MHz
Shape factor 60 dB/3 dB 2.5, nominal
Modulation distortion
Measurement functions THD, SINAD
Measurement range –100 dB to 0 dB
Resolution 0.01 dB
Measurement uncertainty typ. 0.5 dB
AF frequency range 10 Hz to 5 MHz
Trigger
Trigger functions
≤5 MHz,
max. 0.5 × demodulation bandwidth
5 mrad
typ. 1 dB
≤9 MHz
≤18 MHz
RF level, AM, FM, ϕM demodulation
Version 02.00, July 2005 Spectrum Analyzer R&S FSL 9
Ordering information
Order designation Type Order No.
Spectrum Analyzer 9 kHz to 3 GHz R&S FSL3 1300.2502.03
Spectrum Analyzer 9 kHz to 3 GHz,
with tracking generator
Spectrum Analyzer 9 kHz to 6 GHz R&S FSL6 1300.2502.06
Spectrum Analyzer 9 kHz to 6 GHz,
with tracking generator
Accessories supplied
Power cable, quick start guide and CD-ROM (with operating manual and service manual)
Options
Order designation Type Order No. Retrofittable Remarks
Options
OCXO Reference Frequency R&S FSL-B4 1300.6008.02 yes
Additional Interfaces R&S FSL-B5 1300.6108.02 yes video out, IF out, noise
TV Trigger R&S FSL-B6 1300.5901.02 yes
Narrow Resolution Filters R&S FSL-B7 1300.5601.02 yes
Gated Sweep R&S FSL-B8 1300.5701.02 yes
GPIB Interface R&S FSL-B10 1300.6208.02 yes
RF Preamplifier R&S FSL-B22 1300.5953.02 yes
DC Power Supply R&S FSL-B30 1300.6308.02 yes
NiMH Battery Pack R&S FSL-B31 1300.6408.02 yes requires R&S FSL-B30
Firmware/Software
AM/FM/ϕM Measurement Demodulator
Power Sensor Support R&S FSL-K9 1301.9530.02 requires R&S FSL-B5 or
R&S FSL3 1300.2502.13
R&S FSL6 1300.2502.16
source control, AUX port,
R&S NRP power sensor
R&S FSL-K7 1301.9246.02
R&S NRP-Z3/4
10 Spectrum Analyzer R&S FSL Version 02.00, July 2005
Recommended extras
Order designation Type Order No.
19’’ Rackmount Adapter R&S ZZA-S334 1109.4487.00
Soft Carrying Bag R&S FSL-Z3 1300.5401.00
Additional Charger Unit R&S FSL-Z4 1300.5430.02
Matching Pad 75 Ω, L section R&S RAM 0358.5414.02
Matching Pad 75 Ω, series resistor 25 Ω R&S RAZ 0358.5714.02
Matching Pad 75 Ω, L section, N to BNC R&S FSH-Z38 1300.7740.02
SWR Bridge 5 MHz to 3 GHz R&S ZRB2 0373.9017.52
SWR Bridge 40 kHz to 4 GHz R&S ZRC 1039.9492.52
SWR Bridge 10 MHz to 3 GHz
(incl. open, short, load calibration standards)
R&S FSH-Z2 1145.5767.02
Power sensors supported by R&S FSL-K9
Order designation Type Order No.
Average Power Sensor 10 MHz to 8 GHz, 200 mW R&S NRP-Z11 1138.3004.02
Average Power Sensor 10 MHz to 18 GHz, 200 mW R&S NRP-Z21 1137.6000.02
Average Power Sensor 10 MHz to 18 GHz, 2 W R&S NRP-Z22 1137.7506.02
Average Power Sensor 10 MHz to 18 GHz, 15 W R&S NRP-Z23 1137.8002.02
Average Power Sensor 10 MHz to 18 GHz, 30 W R&S NRP-Z24 1137.8502.02
Average Power Sensor 9 kHz to 6 GHz, 200 mW R&S NRP-Z91 1168.8004.02
Thermal Power Sensor 0 Hz to 18 GHz, 100 mW R&S NRP-Z51 1138.0005.02
Thermal Power Sensor 0 Hz to 40 GHz, 100 mW R&S NRP-Z55 1138.2008.02
Version 02.00, July 2005 Spectrum Analyzer R&S FSL 11
Certified Quality System
ISO 9001
DQS REG. NO 1954 QM
Certified Environmental System
ISO
14001
DQS REG. NO 1954 UM
For product brochure, see PD 0758.2790.12
and www.rohde-schwarz.com
(search term: FSL)
¸is a registered trademark of Rohde & Schwarz GmbH & Co. KG · Trade names are trademarks of the owners · Printed in Germany (Bi as)
PD 0758.279 0.22 ·¸FS L · Version 02.00 · August 2 005 · Data with out tolerance limi ts is not binding · Subject t o change
Europe: +4 9 1805 12 4242, customersupport@rohde-schwar z.com
www.rohde-schwarz.com
USA and Canada: 1-888 -837-8772, customer.support@rsa.rohde-schwarz.com
Asia: +65 6 8463710, customersupport.asia@rohde -schwarz.com
Loading...