Rohde and Schwarz FSH3-TV Data Sheet

TV Analyzer ¸FSH3-TV

Specifi cations

Version

01.00

August

2005

Specifi cations

CONTENTS

CONTENTS................................................................................................................................................................................................2

SPECIFICATIONS .....................................................................................................................................................................................3

ANALOG TV RECEIVER .............................................................................................................................................................................4

CABLE TV ANALYZER ...............................................................................................................................................................................4

DIGITAL TV RECEIVER (OPTIONS R&S FSHTV-K21, R&S FSHTV-K22) ...................................................................................................4

SPECTRUM ANALYZER..............................................................................................................................................................................5

TRANSMISSION MEASUREMENTS ...............................................................................................................................................................6

INTERFACES ............................................................................................................................................................................................6

ACCESSORIES .........................................................................................................................................................................................7

PRESELECTOR R&S FSHTV-Z60 ............................................................................................................................................................7

POWER SENSORS R&S FSH-Z1 AND R&S FSH-Z18 ...............................................................................................................................7

DIRECTIONAL POWER SENSOR R&S FSH-Z14 .........................................................................................................................................8

DIRECTIONAL POWER SENSOR R&S FSH-Z44 .........................................................................................................................................9

VSWR BRIDGE AND POWER DIVIDER R&S FSH-Z2 ................................................................................................................................11

DISTANCE-TO-FAULT MEASUREMENT (OPTION R&S FSH-B1) .................................................................................................................11

REFLECTION MEASUREMENTS (ONLY WITH R&S FSH-Z2) .......................................................................................................................12

GENERAL DATA.....................................................................................................................................................................................13

ENVIRONMENTAL CONDITIONS ................................................................................................................................................................13

MECHANICAL RESISTANCE ......................................................................................................................................................................13

POWER SUPPLY .....................................................................................................................................................................................14

ORDERING INFORMATION....................................................................................................................................................................15

OPTIONS .................................................................................................................................................................................................15

OPTIONAL ACCESSORIES ........................................................................................................................................................................15

2 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

Specifications

Specifications apply under the following conditions: 15 minutes warm-up time at ambient temperature, specified environmental
conditions met and calibration cycle adhered to. Data without tolerances: typical values. Data designated as "nominal": design
parameters, i.e. not tested.

Frequency

Frequency range 100 kHz to 3 GHz

Reference frequency

Aging 1 ppm/year
Temperature drift 0 °C to 30 °C

Frequency counter

Resolution 1 Hz

Frequency span
Spectral purity

SSB phase noise f = 500 MHz, 20 °C to 30 °C
30 kHz from carrier <85 dBc/1 Hz
100 kHz from carrier <100 dBc/1 Hz
1 MHz from carrier <120 dBc/1 Hz

Inputs

RF input N female
Input impedance
VSWR 10 MHz to 3 GHz typ. 1.5
Maximum permissible DC voltage at RF

input
Maximum power 20 dBm, 30 dBm (1 W) for max. 3 minutes

Trigger/external reference input

Trigger voltage TTL
Reference frequency 10 MHz
Required level from 50 Ω

Outputs
Tracking generator

Frequency range 5 MHz to 3 GHz
Output level 0 dBm/–20 dBm, selectable
Output impedance

Video output

Output level 1 V
DC position back porch 0 V
Output impedance

TS-ASI output

Output level, peak-to-peak 0.8 V
Data rate 270 Mbit/s
Output impedance

AF output

Spectrum analyzer mode AM (video voltage without AGC) and FM
Analog TV receiver mode in line with standard
Output impedance
Output level adjustable

2 ppm, in addition

30 °C to 50 °C

100 Hz to 3 GHz, 0 Hz

80 V

BNC female, selectable, same connector

10 dBm

N female

analog TV receiver mode BNC female, selectable, same connector

digital TV receiver mode
(option R&S FSHTV-K21,
R&S FSHTV-22)

3.5 mm mini jack

2 ppm/10 °C

50 Ω

as video and TS-ASI output

50 Ω

as trigger/external reference input and TS­ASI output

75 Ω
BNC female, selectable, same connector

as trigger/external reference input and
video output

75 Ω

100 Ω

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 3

Analog TV receiver

Standards B, G, H, D, K, I, L, M, N,
Sound standards IRT-A2, NICAM, BTSC, EIA-J, Korea

Video bandwidth in line with standard 4 MHz, 5 MHz, 5.5 MHz and 6 MHz

Measurements

vision carrier frequency offset
vision/sound carrier power ratio
vision/sound carrier frequency offset
luminance bar amplitude
video S/N, weighted in line with CCIR Rec.

audio mode
NICAM bit error ratio
vision modulation depth, residual picture

video scope
hum modulation
carrier-to-noise power ratio

Measurement uncertainty

Video S/N weighted in line with CCIR Rec. 567

S/N <45 dB typ. <1 dB
S/N 45 dB to 55 dB typ. <3 dB

vision carrier power

(1 channel)

Stereo

567

carrier

Cable TV analyzer

Measurements composite triple beat (CTB) ratio
composite second order (CSO) ratio

Digital TV receiver (options R&S FSHTV-K21, R&S FSHTV-K22)

QAM standards

QAM order 4, 16, 32, 64, 128 and 256QAM
Bandwidth in line with symbol rate 6 MHz, 7 MHz and 8 MHz
Symbol rate 2 MHz to 6.999 MHz

8VSB/ATSC standard

Bandwidth 6 MHz
Symbol rate 10.672238 MHz

Measurements

carrier frequency offset
pilot carrier power and frequency

symbol rate offset
MER (modulation error ratio)

EVM (error vector magnitude)
bit error ratio before RS decoder
packet error ratio or segment error ratio
transport stream rate
constellation diagram
shoulder attenuation in line with

carrier-to-noise power ratio

4 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

option R&S FSHTV-K21 DVB-C, J.83/A /B /C (Europe, US and

Japanese cable TV)

option R&S FSHTV-K22

channel power

(8VSB/ATSC)

(MER measurement range up to 40 dB)

ETSI TR 101 290 (QAM)
or in line with FCC (8VSB/ATSC)

Measurement uncertainty

Carrier frequency offset referenced to carrier frequency <5 ppm
Symbol rate offset referenced to symbol rate <5 ppm

Modulation error ratio

MER <33 dB typ. <1 dB
MER 33 dB to 38 dB typ. <3 dB

Error vector magnitude

EVM >1.5 % typ. <12 % of measured value
EVM 0.9 % to 1.5 % typ. <40 % of measured value
Transport stream rate <5 ppm

equalizer on, 1 channel

Spectrum analyzer

Bandwidth

Resolution bandwidths (–3 dB) 100 Hz to 1 MHz in 1, 3 steps; in addition

Tolerance
1 MHz
Resolution bandwidths (–6 dB) option R&S FSH-K3 installed 200 Hz, 9 kHz, 120 kHz
Video bandwidth 10 Hz to 3 MHz in 1, 3 steps

Sweep time

span > 0 Hz 20 ms to 1000 s, min. 20 ms/600 MHz
span = 0 Hz 1 ms to 100 s

Display range

Intermodulation-free dynamic range third-order intermodulation products

Displayed average noise level

with preamplifier

Inherent spurious

Input related spurious carrier offset >1 MHz <–70 dBc, nominal
2nd harmonic typ. <–60 dBc
signal frequency – 2.0156 GHz

Level display

Reference level –80 dBm to +20 dBm in steps of 1 dB
Display range 100 dB, 50 dB, 20 dB, 10 dB, 1 dB, linear

Display units

Logarithmic dBm, dBµV, dBmV

Linear µV, mV, V, nW, µW, mW, W

Traces
Detectors

Level measurement error

200 kHz

≤ 300 kHz ± 5 %, nominal

± 10 %, nominal

average noise level displayed to +20 dBm

2 × –20 dBm, reference level = –10 dBm
third-order intercept

average value, resolution bandwidth
1 kHz, video bandwidth 10 Hz, reference
level ≤ –30 dBm, 10 MHz to 3 GHz

0 MHz to 2.5 GHz

2.5 GHz to 3 GHz

reference level ≤ –20 dBm, f > 30 MHz,
RBW ≤ 100 kHz

for signal frequencies 2 GHz to 3.2 GHz

1 trace and 1 memory trace
auto peak, maximum peak, minimum peak,

frequency > 1 MHz, at reference level
down to –50 dB, 20 °C to 30 °C

66 dB
+13 dBm

<–105 dBm, typ. –114 dBm

<–120 dBm, typ. –125 dBm
<–115 dBm, typ. –120 dBm

<–80 dBm

typ. <–55 dBc

with transducer also dBµV/m and dBµA/m

with transducer also V/m, mV/m, µV/m and

2

W/m

sample, RMS
<1.5 dB, typ. 0.5 dB

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 5

Markers

Number of markers or delta markers max. 6
Marker functions peak, next peak, minimum,

Marker displays normal (level), noise marker, frequency

Trigger free-running, video, external

center = marker frequency,
reference level = marker level, all markers
to peak

counter (count)

Transmission measurements

Frequency range 10 MHz to 3 GHz
Dynamic range

2.2 GHz to 3 GHz

10 MHz to 2.2 GHz

scalar mode
vector mode, option R&S FSH-K2

scalar mode
vector mode, option R&S FSH-K2

60 dB
80 dB

50 dB
65 dB

Interfaces

Optical interface, baud rate 1200, 2400, 9600, 19200, 38400, 57600

Control interface, control and supply of
power sensor and preselector

7-contact female connector

baud

(type Binder 712)

6 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

Accessories

Preselector R&S FSHTV-Z60

RF input

Input impedance

VSWR, bypass path

VSWR, filter path, RF attenuator ≥5 dB

Maximum permissible DC voltage

Maximum power

Additional level measurement error

Frequency range of filter path
Frequency range of bypass path
Preamplifier
RF output

Output impedance

Power consumption
Dimensions
Weight

frequency > 1 MHz, at reference level
down to –50 dB, 20 °C to 30 °C

Power Sensors R&S FSH-Z1 and R&S FSH-Z18

Frequency range R&S FSH-Z1

R&S FSH-Z18

VSWR

Maximum input power

Measurement range

Signal weighting

effect of harmonics

Absolute measurement uncertainty
(sine signals, no zero offset)

Zero offset after zeroing

Dimensions

Weight

10 MHz to 30 MHz
30 MHz to 2.4 GHz

2.4 GHz to 8 GHz
8 GHz to 18 GHz

average power
peak power <10 µs, 1% duty cycle

effect of modulation

10 MHz to 8 GHz

15 °C to 35 °C
0 °C to 50 °C

8 GHz to 18 GHz

15 °C to 35 °C
0 °C to 50 °C

F connector
(F male with adapter F female/F female)

75 Ω

typ. 1.5

typ. 1.5

80 V

+20 dBm

<1.0 dB, typ. 0.5 dB

100 kHz to 1 GHz

100 kHz to 3 GHz

100 kHz to 3 GHz, selectable

N male

50 Ω

500 mW

169 mm × 116 mm × 30 mm

500 g

10 MHz to 8 GHz
10 MHz to 18 GHz

<1.15
<1.13
<1.20
<1.25

400 mW (+26 dBm),
1 W (+30 dBm)

200 pW to 200 mW (–67 dBm to +23 dBm)

average power

<0.5 % (0.02 dB) at harmonic ratio of
20 dB
<1.5 % (0.07 dB) for continuous digital
modulation

<2.5 % (0.11 dB)
<4.5 % (0.19 dB)

<3.5 % (0.15 dB)
<5.0 % (0.21 dB)

<110 pW

48 mm × 31 mm × 170 mm,
connecting cable 1.5 m
<0.3 kg

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 7

Directional Power Sensor R&S FSH-Z14

Frequency range

Power measurement range

VSWR referenced to 50 Ω
Power-handling capacity,

Insertion loss <0.06 dB
Directivity >30 dB

Average power

Power measurement range

Measurement uncertainty

Zero offset after zeroing
Range of typical measurement error

with modulation

Temperature coefficient

Peak envelope power
Power measurement range

Video bandwidth 4 kHz

Measurement uncertainty 18 °C to 28 °C same as for average power plus effect of

Error limits of peak hold circuit for
burst signals

Duty cycle ≥0.1 and repetition rate ≥100/s

Temperature coefficient 25 MHz to 40 MHz

Load matching

Matching measurement range return loss

Minimum forward power specs met from 0.4 W 0.06 W
Error limits for matching measurements

depending on temperature and matching
(see diagram below)

CW, FM, PM, FSK, GMSK
modulated signals

CF: ratio of peak envelope power to
average power

sine signal, 18 °C to 28 °C, no zero offset

25 MHz to 40 MHz
40 MHz to 1 GHz

FM, PM, FSK, GMSK
AM (80 %)
2 CW carriers with identical power
EDGE, TETRA

25 MHz to 40 MHz
40 MHz to 1 GHz

200 kHz
600 kHz

video bandwidth 4 kHz

200 kHz

600 kHz

20/s ≤ repetition rate <100/s

0.001 ≤ duty cycle < 0.1

40 MHz to 1 GHz

VSWR

25 MHz to 1 GHz

30 mW to 300 W

<1.06

100 W to 1000 W

30 mW to 300 W

30 mW to 300 W/CF

4.0 % (0.17 dB) of measured value

3.2 % (0.14 dB) of measured value
±4 mW

0 % of measured value (0 dB)

±3 % of measured value (± 0.13 dB)
±2 % of measured value (± 0.09 dB)
±0.5 % of measured value (± 0.02 dB), if

standard is selected on the R&S FSH3-TV

0.40 %/K (0.017 dB/K)

0.25 %/K (0.011 dB/K)

0.4 W to 300 W
1 W to 300 W
2 W to 300 W

peak hold circuit

±(3 % of measured value + 0.05 W)
starting from a burst width of 200 µs
±(3 % of measured value + 0.20 W)
starting from a burst width of 4 µs
±(7 % of measured value + 0.40 W)
starting from a burst width of 2 µs
plus ±(1.6 % of measured value + 0.15 W)
plus ±0.10 W

0.50 %/K (0.022 dB/K)

0.35 %/K (0.015 dB/K)

0 dB to 23 dB
>1.15

8 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

Power-handling capacity

Dimensions 120 mm × 95 mm × 39 mm,

connecting cable 1.5 m

Weight 0.65 kg

Directional Power Sensor R&S FSH-Z44

Frequency range 200 MHz to 4 GHz

Power measurement range 30 mW to 120 W

VSWR referenced to 50 Ω

200 MHz to 3 GHz
3 GHz to 4 GHz

Power-handling capacity depending on temperature and matching

(see diagram below)

Insertion loss 200 MHz to 1.5 GHz

1.5 GHz to 4 GHz

Directivity 200 MHz to 3 GHz

3 GHz to 4 GHz

Average power

Power measurement range CW, FM, PM, FSK, GMSK

3GPP WCDMA, cdmaOne, CDMA2000
DAB, DVB-T
other modulated signals
CF: ratio of peak envelope power to
average power

Measurement uncertainty sine signal, 18 °C to 28 °C, no zero offset

200 MHz to 300 MHz
300 MHz to 4 GHz

Measurement uncertainty after zeroing ±4 mW

Range of typical measurement error with
modulation

FM, PM, FSK, GMSK
AM (80 %)
2 CW carriers with identical power

π/4-DQPSK

EDGE
cdmaOne, DAB
3GPP WCDMA, CDMA2000
DVB-T

Temperature coefficient 200 MHz to 300 MHz

300 MHz to 4 GHz

Peak envelope power

Power measurement range DAB, DVB-T, cdmaOne, CDMA2000®,

3GPP WCDMA
other signals at video bandwidth

4 kHz
200 kHz
4 MHz

Measurement uncertainty 18 °C to 28 °C same as for average power plus effect of

*)

If this standard is selected on the R&S FSH3-TV.

CDMA2000® is a registered trademark of the Telecommunications Industry Association (TIA -USA).

®

(300 W with unmodulated envelope)
<1.07
<1.12
120 W to 1000 W

<0.06 dB
<0.09 dB

>30 dB
>26 dB

30 mW to 300 W

®

,

30 mW to 120 W

30 mW to 300 W/CF

4.0 % (0.17 dB) of measured value

3.2 % (0.14 dB) of measured value

0 % of measured value (0 dB)
±3 % of measured value (± 0.13 dB)
±2 % of measured value (± 0.09 dB)
±2 % of measured value (± 0.09 dB)
±0.5 % of measured value (± 0.09 dB)
±1 % of measured value (± 0.04 dB)
±2 % of measured value (± 0.09 dB)
±2 % of measured value (± 0.09 dB)

0.50 %/K (0.022 dB/K)

0.35 %/K (0.015 dB/K)

4 W to 300 W

0.4 W to 300 W
1 W to 300 W
2 W to 300 W

peak hold circuit

*)

*)

*)

*)

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 9

Error limits of peak hold circuit for burst
signals

duty cycle ≥0.1 and repetition rate ≥100/s
video bandwidth

4 kHz

200 kHz

4 MHz

20/s ≤ repetition rate < 100/s

0.001 ≤ duty cycle < 0.1
burst width ≥0.5µs
burst width ≥0.2µs

Range of typical measurement error of
peak hold circuit

cdmaOne, DAB
DVB-T, CDMA2000
video bandwidth 4 MHz and standard
selected on the R&S

Temperature coefficient 200 MHz to 300 MHz

300 MHz to 4 GHz

Load matching

®

, 3GPP WCDMA

FSH3-TV

±(3% of measured value + 0.05 W)
starting from a burst width of 100 µs
±(3% of measured value + 0.20 W)
starting from a burst width of 4 µs
±(7% of measured value + 0.40 W)
starting from a burst width of 1 µs

plus ±(1.6 % of measured value + 0.15 W)
plus ±0.10 W
plus ±5 % of measured value
plus ±10 % of measured value

±(5% of measured value + 0.4 W)
±(15% of measured value + 0.4 W)

0.50 %/K (0.022 dB/K)

0.35 %/K (0.015 dB/K)

Matching measurement range

Return loss 200 MHz to 3 GHz

3 GHz to 4 GHz

VSWR 200 MHz to 3 GHz

3 GHz to 4 GHz

0 dB to 23 dB
0 dB to 20 dB
>1.15
>1.22

Minimum forward power specs met from 0.2 W 0.03 W

Error limits for matching measurements

Power-handling capacity

6

dB

4

2

0

Measurement error

-2

-4
0510

1000

800

600

AVG -10 °C to 35 °C

VSWR 3

400

Forward power

AVG 35 °C to 50 °C

200

100

VSWR 3

0,2

0,4

0,7

0.2 GHz to 3 GHz

3 GHz to 4 GHz

15

PEAK (max. 10 ms), VSWR < 3

AVG -10 °C to 35 °C

1

20

Return loss

VSWR 1.5

23

Frequency

dB

25

4 GHz

Dimensions 120 mm × 95 mm × 39 mm,

connecting cable 1.5 m

Weight 0.65 kg

10 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

VSWR Bridge and Power Divider R&S FSH-Z2

Frequency range 10 MHz to 3 GHz
Impedance

VSWR bridge

Directivity 10 MHz to 1 GHz

Directivity, corrected (option R&S FSH-K2) 2 MHz to 10 MHz

Return loss at test port 20 dB
Return loss at test port, corrected (option R&S FSH-K2) 35 dB
Insertion loss 9 dB

Power divider

Return loss at test port 20 dB

Connectors

Generator input/RF output N male
Test port N female
Control interface 7-contact connector (type Binder)

Calibration standards

Short/open
Connector N male
Impedance
Return loss 46 dB
Power-handling capacity 1 W

General data

Power consumption 500 mW
Dimensions (W × H × D) 169 mm × 116 mm × 30 mm
Weight 485 g

1 GHz to 3 GHz

10 MHz to 3 GHz

50 Ω load

50 Ω

30 dB
25 dB
40 dB
43 dB

50 Ω

Distance-to-Fault Measurement R&S FSH-B1

Display 301 pixels
Maximum resolution, maximum zoom cable length/1023 pixels
Display range return loss

VSWR

Cable length, depending on cable loss 3 m to max. 1000 m
Maximum permissible spurious signal 3 m to max. 1000 m

10, 5, 2, 1 dB/div, linear
1 to 2 and 1 to 6,
with option R&S FSH-K2 in addition
1 to 1.2 and 1 to 1.5

first mixer 1 dB compression point
typ. +10 dBm
IF overload at reference level typ. +8 dB

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 11

Reflection measurements (only with R&S FSH-Z2)

Frequency range 10 MHz to 3 GHz

Display range of return loss 1 dB, 10 dB, 20 dB, 50 dB, 100 dB,

selectable

VSWR display range 1 to 2 and 1 to 6, selectable,

with option R&S

FSH-K2 also 1 to 1.2 and

1 to 1.5

Measurement uncertainty see diagrams

3

2

Measurement

uncertainty / dB

1

0

-1

-2

-3
0 2 4 6 81012141618

Return loss DUT / dB

Measurement uncertainty with scalar measurements

20

3

2

Measurement

uncertainty / dB

1

0

-1

-2

-3
0510

15

20

Return loss DUT / dB

25 30

Measurement uncertainty with vector measurements
(option R&S FSH-K2)

12 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

General data

Display 14 cm (5.7") LC color display
Resolution 320 × 240 pixels
Memory
Settings and traces

Environmental conditions

CMOS RAM

100

Temperature

Operating temperature range R&S FSH3-TV powered from internal

Storage temperature range –20 °C to +60 °C
Battery charging mode 0 °C to 40 °C

Climatic conditions

Relative humidity 95 % at 40 °C (EN 60068)

IP class of protection

battery
R&S FSH3-TV powered from AC power
supply

51

0 °C to 50 °C

0 °C to 40 °C

Mechanical resistance

Vibration sinusoidal complies with EN 60068-2-1, EN 61010-1

Vibration random complies with EN 60068-2-64

Shock complies with EN 60068-2-27

RFI suppression complies with EMC directive of EU

Immunity to radiated interference 10 V/m
Level display

at 10 V/m (reference level ≤–10 dBm)

input frequency
IF
other frequencies

5 Hz to 55 Hz: max. 2 g, 55 Hz to 150 Hz:

0.5 g constant,
12 minutes per axis

10 Hz to 500 Hz, 1.9 g, 30 minutes per
axis

40 g shock spectrum

(89/336/EEC)
and German EMC legislation

<–75 dBm (nominal)
<–85 dBm (nominal)
< displayed noise level

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 13

Power supply

AC supply plug-in AC power supply (R&S FSH-Z33)

External DC voltage 15 V to 20 V
Internal battery NiMH battery

Operating time with fully charged
battery

Battery charging time 4 h with instrument off
Lifetime 300 to 500 charging cycles
Power consumption in charging mode 12 W

Power consumption 7 W to 10 W depending on measurement

Safety complies with EN 61010-1, UL 3111-1,

Test mark VDE, GS, CSA, CSA-NRTL
Dimensions (W × H × D) 170 mm × 120 mm × 270 mm
Weight 2.7 kg
Accessories supplied external power supply, optical USB cable,

3 h to 4 h depending on measurement

100 V AC to 240 V AC, 50 Hz to 60 Hz,
400 mA

mode

mode

CSA C22.2 No. 1010-1

headphones, Quick Start manual, CD­ROM with Control Software R&S FSH
View and documentation

14 TV Analyzer R&S FSH3-TV Version 01.00, August 2005

Ordering information

Designation Type Order No.

TV Analyzer R&S FSH3-TV 2111.7005.63

Options

Designation Type Order No.

Remote Control for R&S FSH3-TV R&S FSHTV-K1 2111.7140.02
DVB-C/J.83/A/B/C (QAM) Firmware for R&S FSH3-TV R&S FSHTV-K21 2111.7211.02
ATSC/8VSB Firmware for R&S FSH3-TV R&S FSHTV-K22 2111.7228.02
Distance-to-Fault Measurement,

includes 1 m cable, R&S FSH-Z2 required
Vector Transmission and Reflection Measurements R&S FSH-K2 1157.3387.02
Receiver Mode R&S FSH-K3 1157.3429.02

Recommended extras

Designation Type Order No.

Preselector for R&S FSH3-TV R&S FSHTV-Z60 2111.7105.02
Spare F Adapter 75 Ω, female/female

for Preselector R&S FSHTV-Z60
Power Sensor 10 MHz to 8 GHz R&S FSH-Z1 1155.4505.02
VSWR Bridge and Power Divider, 10 MHz to 3 GHz
(contains short, open and 50 Ω load for calibration
Directional Power Sensor, 25 MHz to 1 GHz R&S FSH-Z14 1120.6001.02
Power Sensor, 10 MHz to 18 GHz R&S FSH-Z18 1165.1909.02
Directional Power Sensor, 200 MHz to 4 GHz R&S FSH-Z44

Matching Pad 50/75 Ω, 0 Hz to 2700 MHz
Spare RF Cable, 1 m, N male/N female

for R&S FSH-B1
12 V Car Adapter R&S FSH-Z21 1145.5873.02
Serial/Parallel Converter R&S FSH-Z22 1145.5880.02
Carrying Bag R&S FSH-Z25 1145.5896.02
Transit Case R&S FSH-Z26 1300.7627.02
Combined Short/Open and 50 Ω Load for VSWR and DTF

calibration
Spare Short/Open Calibration for R&S FSH-Z2 R&S FSH-Z30 1145.5773.02
Spare 50 Ω Load for R&S FSH-Z2 for VSWR and DTF

calibration
Spare Battery Pack R&S FSH-Z32 1145.5796.02
Spare AC Power Supply R&S FSH-Z33 1145.5809.02
Spare RS-232-C Optical Cable R&S FSH-Z34 1145.5815.02
Spare Headphones R&S FSH-Z36 1145.5838.02
Spare Optical USB Cable R&S FSH-Z37 1300.7733.02
Matching Pad 50/75 Ω, DC to 1000 MHz
Spare CD-ROM with Control Software R&S FSH View and

Documentation for R&S FSH3-TV

R&S FSH-B1 1145.5750.02

R&S FSHTV-Z61 2111.7111.02

R&S FSH-Z2 1145.5767.02

R&S RAZ 0358.5714.02
R&S FSH-Z20 1145.5867.02

R&S FSH-Z29 1300.7504.02

R&S FSH-Z31 1145.5780.02

R&S FSH-Z38 1300.7740.02
R&S FSHTV-Z65 2111.7340.02

Version 01.00, August 2005 TV Analyzer R&S FSH3-TV 15

Certified Quality System

ISO 9001

DQS REG. NO 1954 QM

Certified Environmental System

ISO

14001

DQS REG. NO 1954 UM

¸is a registered trademark of Rohde & Schwarz GmbH & Co. KG · Trade names are trademarks of the owners · Printed in Germany (Bi as)

PD 0758.2648.12 · ¸FSH3-TV · Version 01.00 · August 2005 · Data without tolerance limits is not binding · Subject to change

For product brochure, see PD 0758.2648.12

and www.rohde-schwarz.com

(search term: FSH3-TV)

www.rohde-schwarz.com

Europe: [phone], customersuppor [e-mail]

USA and Canada: 1-888-8 37-8772, customer.support @rsa.rohde-schwarz.com

Asia: [phone], customer support.asia@ rohde-schwarz .com