Page 1
Specifications
FSEA30 FSEB30 FSEM30 FSEK30
Specifications are guaranteed under the following conditions:
30 minutes warmup time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and total calibration performed.
Data without tolerances: typical values only. Data designated "nominal" apply to design parameters and are not tested.
Frequency
Frequency range 20 Hz to 3.5 GHz 20 Hz to 7 GHz 20 Hz to 26.5 GHz 20 Hz to 40 GHz
Frequency resolution 0.01 Hz
Internal reference frequency, nominal
Aging per day
Aging per year1) 2 x10
Temperat ure dri ft ( 0 °C to +50°C) 5 x10
Total error limit (per year) 2.5 x10
External reference frequency 10 MHz or n × 1 MHz, n = 1 to 16
Frequency display with marker
Resolution 0.1 Hz to 10 kHz (as a function of span)
Error limit (sweep time >3 × auto sweep time) ±(marker frequency × reference error + 0.5 % × span + 10 % × resolution bandwidth + 1/2 (last digit))
Frequency counter measures the marker frequency
Resolution 0.1 Hz to 10 kHz (selectable)
Count accuracy (S/N >25 dB) ±(frequency × reference error + 1/2 (last digit))
Display range for frequency axis 0 Hz, 10 Hz to full span
Resolution/error limit of display range 0.1 Hz/1%
Spectral purity (dBc (Hz))
SSB phase noise, f ≤500 MHz
Carrier offset 100 Hz <–87 <–81
Sweep time
Span = 0 Hz 1 µs to 2500 s in 5% steps
Span ≥10 Hz 5 ms to 16 000 s in steps ≤10%
Error limit <1%
Picture refresh rate (span ≤7 GHz) >20 updates/s with 1 trace, >15 updates/s with 2 traces
Sampling rate 50 ns (20 MHz A/D converter)
Number of pixels 500
Time measurement with marker and cursor lines
Resolution 50 ns
Sweep trigger free run, single, line, video, gated, delayed, external
Zero span additionally pretrigger, posttrigger, trigger delay
Resolution bandwidths
3 dB bandwidths (in 1/2/3/5 steps) 1 Hz to 10 MHz
FFT filter (in 1/2/3/5 steps) (see also page 16) 1 Hz to 1 kHz
1)
1x10
–9
for f >500 MHz see diagram below
1 kHz <–107 <–100
10 kHz <–120 <–114
2)
100 kHz
1 MHz
2)
<–119 <–113
<–138 <–132
–7
–8
–7
SSB phase noise (typical values)
12 Spectrum Analyzers FSEx
–60
dBc (Hz)
–70
–80
–90
–100
–110
SSB phase noise
–120
–130
–140
–150
–155
100 Hz 1 kHz 10 kHz 100 kHz 10 MHz1 MHz
FSEA 500 MHz
FSEA 3.5 GHz
FSEB/M/K 500 MHz
FSEB/M/K 3.5 GHz
FSEM/K 26 GHz
FSEK 40 GHz
Carrier offset
Page 2
Specifications
FSEA30 FSEB30 FSEM30 FSEK30
Bandwidth error ≤3 MHz <10 %
5 MHz <15%
10 MHz +25%, –10%
Shape factor 60:3 dB <1 kHz <6
1 kHz to 2 MHz <12
>2 MHz < 7
Video bandwidths 1 Hz to 10 MHz, 1/2/3/5 steps
Level
Display range noise floor displayed to 30 dBm
Maximum input level
RF attenuation 0 dB
DC voltage 0 V
CW RF power 20 dBm (=0.1 W)
Pulse spectral density 97 dBµV (MHz)
RF attenuation ≥10 dB
DC voltage 0 V
CW RF power 30 dBm (=1 W)
Max. pulse voltage 150 V 50 V
Max. pulse energy (10 µs) 1mWs 0.5 mWs
1 dB compression of input mixer
(0 dB RF attenuation)
Displayed average noise floor in dBm (0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω)
Frequency 20 Hz <–80 <–74
1 kHz <–110 <–104
10 kHz <–125 <–119
100 kHz <–135 <–129
1 MHz <–145, –150 typ. <–142, typ. –145
10 MHz to 3.5/6 GHz <–145, –150 typ. <–142, –147 typ. <–138, –140 typ.
6 GHz to 7 GHz – <–139 <–135, –138 typ.
7 GHz to 18 GHz ––<–138, –140 typ. <–134, –139 typ.
18 GHz to 26.5 GHz – – <–135, –138 typ. <–131, –136 typ.
26.5 GHz to 30 GHz –––<–120, –125 typ.
30 GHz to 40 GHz – – – <–116, –122 typ.
Max. dynamic range, bandwidth 1 Hz
Displayed noise floor to 1 dB compression 165 dB 162 dB 160 dB
Max. harmonics suppression, f >50 MHz >90 dB
Max. intermodulation-free range
50 MHz to 3.5 GHz (nominal) 115 dB ––
150 MHz to 7/26.5 GHz (nominal) – 115 dB 112 dB
Intermodulation
TOI, intermodulation-free dynamic range,
level 2 × −30 dBm, ∆f >5 × RBW or >10 kHz
>84 dBc for f >50 MHz
(TOI >12 dBm,
18 dBm typ. )
>90 dBc for f >150 MHz
(TOI >15 dBm,
20 dBm typ. )
Intermodulation-free range at –40 dBm mixer level 105 dB
Intercept point k2 (dBm) >25, >40 typ. for
f <50 MHz, >45,
>50 typ. for f >50 MHz
Immunity to interference
Image frequency (dB) >80, >90 typ. >80, >90 typ. for f <22 GHz
Intermediate frequency (dB) >100 dB >75 dB
Spurious response (f >1 MHz, without input signal,
0 dB attenuation)
Span <30 MHz <–110 dBm
Span ≥30 MHz <–100 dBm
f
= 25.06 MHz, 25.175 MHz, 5.7172 GHz <–100 dBm
in
fin = 60 MHz <–110 dBm <–100 dBm
f
= 14.1894 GHz, 15.6722 GHz
in
Span >10 MHz −90 dBm
Other interfering signals (mixer level <–10 dBm) <–80 dB
3)
+10 dBm nominal
>94 dBc for f >100 MHz
>80 dBc for f >7 GHz,
(TOI >17 dBm, 22 dBm typ.;
>10 dBm for f >7 GHz)
>25 for f <150 MHz, >35 typ.,
>40 for f >150 MHz, >45 typ.
>75, >80 typ. for f >22 GHz
<–75 dB3)
Spectrum Analyzers FSEx 13
Page 3
Specifications
FSEA30 FSEB30 FSEM30 FSEK30
Level display
Measurement display 500 × 400 pixels (with one diagram displayed); max. 2 diagrams with independent settings
Logarithmic level range 10 dB to 200 dB, in steps of 10 dB
Linear level range 10% of reference level per division (10 divisions) or logarithmic scaling
Tra ces max. 4 per diagram (max. 2 if 2 diagrams are displayed)
Trace detector max peak, min peak, auto peak (normal), sample, rms, average
Trace functions clear/write, max hold, min hold, average
Setting range of reference level
Logarithmic level display –130 dBm to 30 dBm, in steps of 0.1 dB
Linear level range 7.0 nV to 7.07 V in steps of 1%
Units of level axis dBm, dBµV, dBmV, dBµA, dBpW (logarithmic and linear level display);
Level measurement uncertainty (–40 dBm, RF attenua-
The values are guaranteed for bandwidths from 10 Hz to 30 kHz and 100 kHz to 10 MHz.
tion 20 dB, reference level –15 dB, RBW 5 kHz)
Absolute error limit at 120 MHz <0.3 dB
Frequency response (10 dB RF attenuation)
<1 GHz <0.5 dB
1 GHz to 3.5/7 GHz <1 dB
7 GHz to 18 GHz – <2 dB
18 GHz to 26.5 GHz – <2.5 dB4)
26.5 GHz to 40 GHz – – <3 dB4)
Attenuator error limit <0.3 dB
IF gain error <0.2 dB (0.1 dB typ.)
Display nonlinearity
Logarithmic level display
(RBW ≥1kHz,analog)
0 dB to –50 dB <0.3 dB
–50 dB to –70 dB <0.5 dB
–70 dB to –80 dB –
–70 dB to –95 dB <1 dB
Linear level display 5% of reference level
Bandwidth switching error
1 Hz to 30 kHz/100 to 500 kHz <0.2 dB
1 MHz to 10 MHz <0.3 dB
Total measurement uncertainty (0 dB to 50 dB below
reference level, span/RBW <100, rss 95% reliability)
<1 GHz <1 dB
1 GHz to 3.5/7 GHz <1.5 dB
7 GHz to 18 GHz – <2.5 dB
18 GHz to 26.5 GHz – <3 dB4)
26.5 GHz to 40 GHz ––<3.5 dB
Pulse amplitude error (single pulses)
Bandwidth <1 MHz/≥1 MHz <0.5 dB, nominal/<2 dB, nominal
Trigger functions
Trigger free run, line, video, RF, external
Delayed sweep
Trigger source free run, line, video, RF, external
Delay time 100 ns to 10 s, resolution 1 µs min. or 1% of delay time
Error of delay time ±(1 µs + (0.1% x delay time))
Delayed sweep time 2 µs to 1000 s
Gated sweep
Tri gge r so urce external, RF level
Gate delay 1 µs to 100 s
Gate length 1 µs to 100 s, resolution min. 1 µs or 1% of gate length
Error of gate length ±(1 µs + (0.05% × gate length))
Gap sweep (span = 0 Hz)
Trigger source free run, line, video, RF, external
Pretrigger 1 µs to 100 s, 50 ns resolution, dependent on sweep time
Trigger to gap time 1 µs to 100 s, 50 ns resolution, dependent on sweep time
Gap length 1 µs to 100 s, 50 ns resolution
quasi-analog display of all results
mV, µV, mA, µA, pW, nW (linear level display)
4)
4
)
4
)
14 Spectrum Analyzers FSEx
Page 4
Specifications
FSEA30 FSEB30 FSEM30 FSEK30
Audio demodulation
AF demodulation types AM and FM
Audio output loudspeaker and headphones output
Marker stop time 100 ms to 60 s
Inputs and outputs (front panel)
RF input N female, 50 Ω adapter system, 50 Ω, N
male and female, 3.5 mm
male and female
VSWR (RF attenuation ≥10 dB)
f <3.5 GHz <1.5
f <7 GHz – <2.0
f <26.5 GHz – <3 <2.5
f <37 GHz ––<2.5
f <40 GHz – – 2.5 typ.
Attenuator 0 dB to 70 dB, selectable in 10 dB steps
Probe power +15 V DC, –12.6 V DC and ground, max. 150 mA
Power supply and coding connector for antennas etc
12-contact Tuchel
(antenna code)
Supply voltages ±10 V, max. 100 mA, ground
AF output Z
= 10 Ω , jack plug
out
Open-circuit voltage adjustable up to 1.5 V
Inputs and outputs (rear panel)
IF 21.4 MHz Z
Level 0 dBm at reference level, mixer level > –60 dBm
Video output Z
Voltage (resolution bandwidth ≥1 kHz) 0 V to 1 V, full scale (open-circuit voltage); logarithmic scaling
Reference frequency
Output, usable as input BNC female
Output frequency 10 MHz
Level 10 dBm nominal
Input 1 MHz to 16 MHz, integer MHz
Required level >0 dBm into 50 Ω
Sweep output BNC female, 0 V to 10 V in sweep range
Power supply connector for noise source BNC female, 0 V and 28 V, selectable
External trigger/gate input BNC female, >10 kΩ
Volta ge –5 V to +5 V, adjustable
IEC/IEEE-bus control interface to IEC625-2 (IEEE 488.2), command set: SCPI 1994.0
Connector 24-contact Amphenol female
Interface functions SH1, AH1, T6, L4, SR1, RL1, PP1, DC1, DT1, C11
Serial interface RS-232-C (COM 1 and COM 2), 9-contact female connectors
Mouse interface PS/2 mouse compatible
5)
Plotter
Printer interface parallel (Centronics compatible) or serial (RS-232-C)
Keyboard connector 5-contact DIN female for MF-2 keyboard
User interface 25-contact Cannon female
Connector for external monitor (VGA) 15-contact female
= 50 Ω , BNC female, bandwidth >1 kHz or resolution bandwidth
out
= 50 Ω , BNC female
out
via IEC/IEEE bus or RS-232-C; plotter language: HP-GL
General data
Display 24 cm LC TFT colour display (9.5")
Resolution 640 × 480 pixels (VGA resolution)
Pixel failure rate <2 x 10
Mass memory 1.44 Mbyte 3 ½" diskette drive, hard disk
Operating temperature range
Nominal temperature range +5°C to +40 °C
Limit temperature range 0°C to +50°C
Storage temperature range –40°C to +70°C
Humidity +40°C at 95 % relative humidity (IEC68-2-3)
Mechanical resistance
Vibration, sinusoidal 5 Hz to 150 Hz, max. 2 g at 55 Hz; 55 Hz to 150 Hz, 0.5 g const.
to IEC68-2-6, IEC 68-2-3, IEC1010-1, MIL-T-28800D, class 5
Vibration, random 10 Hz to 300 Hz, acceleration 1.2 g (rms)
–5
adapter system, 50 Ω,
N male and female, K
male and female, 2.4 mm
female
Spectrum Analyzers FSEx 15
Page 5
er
r
000
000
000
00
0
,1
1
3
010030030
p
Specifications
FSEA30 FSEB30 FSEM30 FSEK30
Shock 40 g shock spectrum, to MIL-STD-810 D and MIL-T-28800 D, classes 3 and 5
Recommended calibration interval 1 year (2 years for operation with external reference)
RFI suppression to EMC directive of EU (89/336/EEC) and German EMC legislation
Power supply
AC supply 200 V to 240 V: 50 Hz to 60 Hz, 100 V to 120 V: 50 Hz to 400 Hz, class of protection I to VDE 411
Power consumption 180 VA 195 VA 230 VA 230 VA
Safety to EN61010-1, UL3111-1, CSA C22.2 No. 1010-1, IEC 1010-1
Test mark VDE, GS, UL, cUL
Dimensions in mm (W x H x D) 435 x 236 x 460 (5 HU) 435 x 236 x 570 435 x 236 x 570
Weight in kg 22.7 23.2 25.2 25.8
1)
After 30 days of operation.
2)
Valid for span >100 kHz.
3)
For models with option FSE-B23: <–50 dBm.
4)
For frequencies >7 GHz: error after calling peaking function. For sweep times <10 ms/GHz: additional error 1.5 dB.
5)
The plot function is not available if option FSE-B15 is installed.
Specifications
FFT filter
High frequency resolution due to very small shape factor of 2.5
Extremely short measurement time, up to 150 times faster than with conventional
filters
Resolution bandwidths (RBW)
3 dB bandwidth
in 1/2/3/5 steps 1 Hz to 1 kHz
Bandwidth error 2%, nominal
Shape factor 60:3 dB 2.5, nominal
Display range for frequency axis
Min. span 25
Max. span 100000
100
10
time in s
wee
1
1
1
0
0,0
Sweep time for 10 kHz Span
1
1
Level measurement error
Additional total level error,
referred to RBW 5 kHz <1dB
Max. display range 100 dB
Immunity to interference
Spurious response ≤100 dBm
1 dB Attenuator FSE-B13
Frequency range max. 7 GHz (stop frequency ≤7 GHz)
Setting range of RF attenuation 0 dB to 70 dB
Step width 1 dB
Additional attenuator uncertainty <0.1 dB
x RBW
x RBW, max. 2 MHz
FFT filt
Analog filte
External Mixing FSE-B21
LO output/IF input (front panel) SMA female, 50 Ω
LO signal 7.5 GHz to 15.2 GHz
Amplitude +15.5 dBm ±3 dB
IF signal 741.4 MHz
Full-scale level –20 dBm
IF input (front panel) SMA female, 50 Ω
IF signal 741.4 MHz
Full-scale level –20 dBm
Level measurement error at IF inputs
(IF level –30 dBm,
reference level –20 dBm, RBW 30 kHz) <1 dB
Increased Level Accuracy FSE-B22
Total level error ≤0.5 dB with 10 dB RF attenuation
Specifications are valid for:
Temperature range -/+20°C to +30°C
Frequency range 10 MHz to 2 GHz
Resolution bandwidths 5 kHz to 30 kHz/300 kHz/1 MHz
Signal level 10 dB to 50 dB below reference level
Stop frequency ≤2 GHz
Sweep time ≥3 x auto sweep time
≤0.6 dB with 20/30/40 dB RF attenua-
tion
Broadband Output 741.4 MHz FSE-B23
FSE-B23 reduces the suppression of other interference signals to –50 dBm and
must not be combined with FSE-K10/-K11.
FSEA FSEB FSEM FSEK
Gain from RF input to
IF output (dB)
3 dB BW (MHz)
1)
f <7 GHz.
2)
7 GHz to 26.5 GHz.
3)
7 GHz to 40 GHz.
6 6 4 4
1)
60 150
150
40 to 80
2)
1)
150
40 to 120
3)
Spectrum Analyzers FSEx 16
Page 6
Connector BNC
Impedance 50 Ω
For maximum bandwidth set instrument to 10 MHz RBW. The output level is a
function of the mixer level, which equals the input signal level minus the set RF
attenuation.
The typical loss between mixer level and IF output is 2 dB for FSEM/K, and 0 dB
for FSEA/B.
44 GHz Frequency Extension for FSEK FSE-B24
Frequency range 20 Hz to 44 GHz
Intermodulation
3rd-order intercept point (TOI) ∆ f >5 x resolution bandwidth or >10 kHz
>40 GHz +15 dBm typ.
2nd harmonic intercept point (SHI) >25 dBm for f <150 MHz
>40 dBm for f >150 MHz
Level measurement error
Frequency response (10 dB RF attenuation)
40 GHz to 44 GHz <4.0 dB
1)2)
Total measurement error
(0 dB to 50 dB below reference level)
40 GHz to 44 GHz <4.5 dB
1)2)
Level
Displayed average noise level (DANL)
(0 dB RF attenuation, RBW = 10 Hz, VBW = 1 Hz, 20 averages, trace average,
span 0 Hz, 50 Ω termination)
40 GHz to 42 GHz <–112, –128 dBm typ.
42 GHz to 43 GHz <–108, –113 dBm typ.
43 GHz to 44 GHz <–105, –110 dBm typ.
Ordering information
Order designation Ty pe Order No.
Spectrum Analyzer 20 Hz to 3.5 GHz FSEA30 1065.6000.35
Spectrum Analyzer 20 Hz to 7 GHz FSEB30 1066.3010.35
Spectrum Analyzer 20 Hz to 26.5 GHz FSEM30 1079.8500.35
Spectrum Analyzer 20 Hz to 40 GHz FSEK30 1088.3494.35
Accessories supplied
Power cable, operating manual, spare fuses;
FSEM: test-port adapter 3.5 mm female (1021.0512.00) and N female
(1021.0535.00)
FSEK: test-port adapter K female (1036.4790.00) and N female (1036.4777.00)
Options (see also fold-in page)
7 GHz Frequency Extension for FSEA FSE-B2 1073.5044.02
Vector Signal Analyzer FSE-B71)1066.4317.03
Tracking Generator 3.5 GHz FSE-B81) 1066.4469.02
3.5 GHz with I/Q modulator FSE-B91) 1066.4617.02
7 GHz FSE-B101) 1066.4769.02
7 GHz with I/Q modulator FSE-B111) 1066.4917.02
Switchable Attenuator for Tracking Generator FSE-B122)1066.5065.02
1 dB Attenuator FSE-B13
Controller for FSE (mouse and keyboard
included)
Ethernet Interface 15-contact AUI connector FSE-B16
Thin-wire BNC connector FSE-B165) 1073.5973.03
RJ-45 connector (twisted pair) FSE-B165) 1073.5973.04
2nd IEC/IEEE-Bus Interface for FSE FSE-B175) 1066.4017.02
2)3)
1119.6499.02
FSE-B154)1073.5696.06
5)
1073.5973.02
Inputs and outputs (front panel)
RF input adapter system, 50 Ω, N male und
female, K male und female, 2.4 mm
female
VSWR (RF attenuation >0 dB)
f >40 GHz <3.0:1 typ.
1)
Error after running the preselector peaking function. For sweep <10 ms/GHz: additional error
1.5 dB.
2)
Temperature range 20°C to 35 °C.
Order designation Ty pe Order No.
Removable Hard Disk FSE-B184) 1088.6993.02
2nd Hard Disk for FSE-B18
(firmware included)
FSE-B19 1088.7248.02
External Mixing FSE-B21 1084.7243.02
Increased Level Accuracy up to 2 GHz FSE-B224) 1106.3480.02
Broadband Output 741.4 MHz FSE-B234) 1088.7348.02
44 GHz Frequency Extension for FSEK FSE-B244) 1106.3680.02
Software
Noise Measurement Software, Windows FS-K31) 1057.3028.02
Phase Noise Measurement Software, Windows FS-K41) 1108.0088.02
GSM Application Firmware Mobile station FSE-K101) 1057.3092.02
Base station FSE-K111) 1057.3392.02
EDGE Application Firmware Mobile station FSE-K201) 1106.4086.02
Base station FSE-K211) 1106.4186.02
Recommended extras
Service Kit FSE-Z1 1066.3862.02
DC Block 5 MHz to 7000 MHz (type N) FSE-Z3 4010.3895.00
10 kHz to 18 GHz (type N) FSE-Z4 1084.7443.02
Microwave Measurement Cable and Adapter
Set for FSEM
FSE-Z15 1046.2002.02
Harmonic Mixer 40 GHz to 60 GHz FS-Z601) 1089.0799.02
50 GHz to 75 GHz FS-Z751) 1089.0847.02
60 GHZ to 90 GHz FS-Z901) 1089.0899.02
75 GHZ to 110 GHz FS-Z1101) 1089.0976.00
Spectrum Analyzers FSEx 17
Page 7
Order designation Ty pe Order No.
Order designation Ty pe Order No.
Service Manual – 1065.6016.24
Headphones – 0708.9010.00
Keyboard German PSA-Z2 1007.3001.31
US PSA-Z2 1007.3001.02
PS/2 Mouse FSE-Z2 1084.7043.02
IEC/IEEE-Bus Cable 1 m PCK 0292.2013.10
2 m PCK 0292.2013.20
19" Rack Adapter, with front handles ZZA-95 0396.4911.00
Transit Case ZZK-954 1013.9395.00
Transit Case (FSEM30 and FSEK30 only) ZZK-955 1013.9408.00
Matching Pads, 75 Ω L section RAM 0358.5414.02
Series resistor, 25 Ω RAZ 0358.5714.02
see accessories for Test
Accessories for current, voltage and fieldstrength measurement
Receiver and Spectrum
Analyzers, data sheet
PD 0756.4320
SWR Bridge 5 MHz to 3000 MHz ZRB 2 0373.9017.52
40 kHz to 4 GHz ZRC 1039.9492.52
High-Power Attenuators 100 W
50 W
Steps: 3/6/10/20/30 dB
RBU 100
RBU 50
1073.8820.xx
1073.8895.xx
xx: 03/06/10/
20/30
ESV-Z3 0397.7014.52
For FSEM only:
Test-Po rt A dap ter N m ale
– 1021.0541.00
3.5 mm male – 1021.0529.00
For FSEK only:
Test-Po rt A dap ter N m ale
– 1036.4783.00
K male – 1036.4802.00
2.4 mm female FSE-Z5 1088.1627.02
Probe Power Connectors 3-contact – 1065.9480.00
1)
Extra data sheets available.
2)
FSE-B12 and FSE-B13 cannot be fitted together.
3)
In combination with FSE-B22 factory-fitted only.
4)
Cannot be retrofitted, factory-fitted only.
5)
FSE-B16 and FSE-B17 require option FSE-B15.
Printed in Germany 0501 (Bi ko)
ROHDE& SCHWARZ GmbH & Co. KG ⋅ Mühldorfstraße 15 ⋅ 81671 München ⋅ Germany ⋅ P.O.B. 80 14 69 ⋅ 81614 München ⋅ Germany ⋅ Telephone +49894129-0
www.rohde-schwarz.com ⋅ Customer Support: Tel. +49 1805124242, Fax +4989 4129-13777, E-mail: CustomerSupport@rohde-schwarz.com
PD 0757.1519.28 ⋅ Spectrum Analyzers FSEx ⋅ Trade names are trademarks of the owners ⋅ Subject to change ⋅ Data without tolerances: typical values
Loading...