ROE BP2, BP3, BP5 User Manual

User Manual P1

BP

User Manual

Control System

Table of Contents

Safety Information

03

Specication

06

Connection

07

Physical Connection

17

Accessories

Installation

10

11

19

21

Package

20

Service and Maintenance

User Manual P2

WARNING!

Safety hazard.

Risk of severe

injury or death.

Refer to manual before

installing, powering

or servicing.

Hazardous voltage.

Risk of lethal or

severe electric shock.

Hot surface.

Do not touch.

Fire hazard. Emission hazardous

to eyesight.

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to re hazards, electric shock and falls.

Read this manual before installing, powering or servicing this product, follow the safety precautions

listed below and observe all warnings in this manual and printed on the product.

If you have questions about how to operate the tile safely, please contact your ROE supplier.

PROTECTION FROM ELECTRIC SHOCK

Connect the product to AC mains power within the range 100-240V nominal at 50 or 60 Hz only.

Disconnect the product from power when not in use.

Always ground (earth) the product electrically.

Before using the product, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices.

Do not use the product if the power cable or a power plug is in any way damaged, defective or showing signs of overheating.

Do not attempt to open any cover.

Refer any service operation not described in this manual to a qualied technician.

01

Safety Information:

Read the safety precautions in this section before

installing, powering, operating or servicing this product.

The following sysmbols are used to identify important safety information on the product and in this manual:

WARNING! WARNING! WARNING! WARNING! WARNING! WARNING!

User Manual P3

The data cables provided with this system have special properties for safety. They are not user serviceable. If the data cables are damaged, replace them only with new ones. Never try to repair a data cable. Per requirements of the National Electrical Code in the USA, the length of a data cable must not exceed 100 m (332 feet). Avoid exposure of data cables to accidental contact with lightning or power conductors.

PROTECTION FROM FIRE

Do not stick lters, masks or other materials directly onto LED modules.

Do not modify the product in any way not described in this manual.

Install only genuine ROE parts in or on the product unless an alternative is described in this manual.

Create an installation by installing tiles at the top and working downwards. Disassemble an installation by removing tiles at the bottom and working upwards.

Check that all external covers and rigging hardware are securely fastened.

Block access below the work area and work from a stable platform whenever installing, servicing or moving the product.

Do not operate the product full load if the ambient temperature of power units (Ta) exceeds 50°C (122° F) or less than -20°C(-4° F).

PROTECTION FROM INJURY

Important warnings

Maximum and minimum ambient temperature:

The maximum ambient temperature for the LED wall is 50 °C; the minimum temperature is (-20°C.)

High leakage current:

The combination of power boxes in an installation results in increased levels of Leakage current. In order to avoid risk of electric shock due to high leakage current, proper grounding of the installation is required.

Power system

Mains cords:

The power cords delivered with this system have special properties for safety. They are not user Serviceable. If the power cords are damaged, replace them only with new ones. Never try to repair a power cord.

This equipment MUST be earthed:

In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding type plug will expose you to the risk of electric shock.

User Manual P4

Data cables:

®

Black Pearl tiles cannot be hot swapped:

Always disconnect the power cord from the control box before connecting or disconnecting the cable string or one of Black Pearl tiles.

FRAME PROTECTION

Certification

Water>150°C

FirePowder

Danger

Note: At normal temperature environment, Magnesium alloy is abosolutely stable and safe. It’s dangerous only in:

1. Temperature higher than 150°C with water;

2. Powder with re.

Mg

POWER SUPPLY

HWA200-4V6

INPUT 100-240V~, 50/60HZ

4005407

CONFORMS TO UL STD.60950-1 CERTIFIED TO CSA STD. C22.2 NO.60950-1-07

ROE Visual Co.,Ltd

Pn=160W Un=4.6V In=35A Max.Operating temperature is 50°C.

OUTPUT POWER CONSUMPTION: 160W

User Manual P5

500.0

Black Pearl Specication: Black Pearl Dimension:

Specification:

02

A. Horizontal Connector

B. Control Button

C. Handle

D. Horizontal Assistant Position bead

E. Vertiacal Assistant Position bead

F. Power In

G. Power Out

H. Data In

I. Data Out

J. Vertical Connector

L. Function Button

M. Hole-Assisted for stacking system

N. Rubber Grip

User Manual P6

BP tiles rear components

90.0

F

A B

C

D

E I

H

J

L

M

N

G

D

E E

(Unit: mm)

The Black Pearl is a cost-ecient version from Black OnyX. It has the same award-winning tile design. The innovative design has successively won many famous design awards including IF Gold Award, Reddot Award, G-Mark Design Award, Design For Asia Award. The innovative and friendly design supports a fast and simple setup for both own and ground-supported setups well suited to the needs of large events, concerts and exhibitions. Featuring a HD pixel pitch(3.9mm) and outstanding color processing, the product also promises high-end performance in TV studios and lecture halls.

Pixel Pitch 3.91mm 5.21mm

Black Pearl BP3 BP5

Black SMD 3-in-1

140H/140V degrees

LED Conguration

Viewing Angle

Max. Brightness (After calibration)

1,500 nits NationStar 2020

Pixel Density 65,536/sqm 36,864/sqm

3000Hz

6000:1 5000:1 5000:1

16bit

Refresh Rate

Contrast

Nova Evision EvisionProcessor

Gray Scale

1/16

3840Hz

1/6Scan

Tile Dimension(W×H×D) 500.0×500.0×90.0(mm) 19.7”×19.7”×3.5”

Magnesium AlloyTile Material

Tile Weight 8.7kg/19.2lbs

Max. Power/Tile

160W

2.84mm

Pixel/Tile 128×128 96×96176×176

BP2

1,500 nits NationStar 1515

123,904/sqm

1920Hz

1/11

9.4kg/20.7lbs

170W 160W

8.7kg/19.2lbs

12 tiles

1×20 tiles (0.5m hanging bar)

1×17 tiles (1m hanging bar)

Max. Concave 10°, Max. Convex 10°

Max. Stacking

Max. Hanging

Curve(optional)

CE, ETL, FCC

Certications

* Notes: The max. hanging supports up to 20 tiles when the safety factor is 5. The convex capability only applies to custom tile, not the standard one.

Operating Temp/Humidity

Storage Temp/Humidity

-20°C~50°C, 10~90%RH

-40°C~60°C, 10~90%RH

Lifetime

≥50000h

03

Connection

User Manual P7

Evision

AC 220V

USB

DVI

①

②

Evision

AC 220V

USB

DVI

①

②

BP Built in Power Supply Input Voltage AC 220V

Hanging System

BP Built in Power Supply Input Voltage AC 110V

1. Neither Header nor Connector can load more than 20 tiles of BP.

2. When the Input Voltage is 220V, one Power Cable can load 16 tiles of BP; and the Input Voltage is 110V, one Power Cable can load 8 tiles of BP.

Notes:

AC 220V AC 220V AC 220V AC 220V AC 220V AC 220V

③

④

⑤

⑦

⑥

⑤ ⑥

⑧

⑦ ⑧

AC 220V AC 220V AC 220V AC 220V AC 220V AC 220V

③

④

16 tiles high 8 tiles high

BP BP BP BP BP BP

Data

Power and Data connections of BP tiles

Power

WeiPu

User Manual P8

Evision

AC 220V

USB

DVI

①

②

BP Built in Power Supply Input Voltage AC 220V

Stacking System

1. Base Bar can load no more than 12 tiles of BP.

2. When the Input Voltage is 220V, one Power Cable can load 16 tiles of BP; and the Input Voltage is 110V, one Power Cable can load 8 tiles of BP.

Notes:

AC 220V AC 220V AC 220V AC 220V AC 220V AC 220V

③

④

⑤

⑧⑦

12 tiles high

BP BP BP BP BP BP

⑥

User Manual P09

HD101 Processor loading with BP3

This document is valid for Evision system with:

Processor rmware: FPGA: 2.63 / ARM 3.07 / LCD 1.15 Tile rmware: FPGA 9.60

Input resolutions for the processor:

1024 x 768 1280 x 720

Every port supports a rectangular area, below tables show the possible number of tiles high and wide (for 50 and 60Hz). If in a creative setup there are gaps or missing tiles, the supported rectangular area stays the same as if there would be tiles.

1440 x 900 1680 x 1050

50Hz: 38 tiles 60Hz: 32 tiles

50Hz

Tile resolution:

Max tiles per processor output

Recommended mapping for standard frame delay (1 frames @ processor, 1 frame @ receiver card):

Recommended mapping for minimum frame delay (0 frames @ processor, 1 frame @ receiver card):

128 x 128 pixels (500mm x 500mm)

1

H\W

2

3

4

5

6

7

8

9

10

11

12

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

××× ××××

×

√√√√√√√√√√√√√√√

√

√√√√√√√√√√√√√ √

√

√√√√√

60Hz

1

H\W

2

3

4

5

6

7

8

9

10

11

12

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

× ×

×

× ×

× ××

×

× ×

×

××

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

× ×

×

×××

×

× ×

×

× ×

×

×××× ×××××

××

×

√√√√√√√√√√√√√√√

√

√√√

√

××

√√√

√

√√√√√ √ √ √√

√

1366 x 768 1400 x 1536 (max height)

1920 x 1080 2560 x 820 (max width)

Example 1: 50Hz, 9 tiles wide, 4 tiles high → OK Example 2: 50Hz, 9 tiles wide, 5 tiles high → not OK Example 3: 60Hz, 9 tiles wide, 4 tiles high →not OK

Example 1: 50Hz, 9 tiles wide, 4 tiles high → not OK, too wide Example 2: 50Hz, 4 tiles wide, 9 tiles high → OK Example 3: 60Hz, 4 tiles wide, 9 tiles high → not OK

Max width per port is 512 pixels. According tables for standard frame delay, but max 4 tiles wide.

Accessories

04

User Manual P10

Name

SAP No.

Dimension

Weight

Evision

201000S0007

W480×H45×D240mm

2.30kg

:

Name

SAP No.

Dimension

Weight

Max Length

Data Cable

208004S0242

30m

1.42kg

100m

:

Name

SAP No.

Dimension

Max.

Capacity

Flightcase

309003-00106

W1165×H835×D617mm

8 tiles of BP

:

Name

SAP No.

Dimension

Weight

Max Current

Power Cable

208001S0754

10m

1.60kg

16A

:

Name

SAP No.

Data Cable

201000S0243

:

Dimension

Weight

0.75m

0.16kg

:

Name

SAP No.

Data Cable

208004S0244

:

Dimension

Weight

0.35m

0.08kg

:

Name

SAP No.

Dimension

Weight

Power Cable

208001S0862

0.35m

0.1kg

:

Name

SAP No.

Dimension

Weight

Material

Max loading

Max loading of tiles

Hanging Bar

207002S0046

W494×H158×D205mm

4.50Kg

Aluminium 6063

20945N(safe factor 5)

Max loading/5/weight of tile≈20 tiles

:

Name

SAP No.

Dimension

Weight

Material

Max loading

Max loading of tiles

Hanging Bar

207002S0047

W94×H158×D205mm

7.70Kg

Aluminium 6063

16295N(safe factor 5)

Max loading/5/2/weight of tile≈17 tiles

:

Name

SAP No.

Dimension

Weight

Material

Stacking Bar

207002S0057

W494×H60×D135mm

7.90Kg

Aluminium 6063

:

Name

SAP No.

Dimension

Weight

Material

Stacking Bar

207002S0058

W994×H60×D135mm

11.87Kg

Aluminium 6063

:

Name

SAP No.

Dimension

Max.

Capacity

Flightcase

309003-00106

W1165×H835×D617mm

8 tiles of BP

:

Name

SAP No.

Dimension

Weight

Material

Base Truss

304012-00503

W1000×H290×D50mm

7.40Kg

Aluminium 6063

:

Name

SAP No.

Dimension

Weight

Material

Rear Support Truss

304012-00504

W1000×H290×D50mm

4.35Kg

Aluminium 6063

:

Name

SAP No.

Dimension

Weight

Material

Rear Bridge

206002S0178

W182×H133×D35mm

0.93Kg

Aluminium 6063

:

⑧

User Manual P11

Installation:

05

Hanging System

0.5m Hanging bar Dimensions:

1m Hanging bar Dimensions:

Hanging bar components:

494mm

994mm

158mm

205mm 205mm

Hanging ClampsAdjusting Knob

Adjusting Screw

Vertical Assitant Position Bead Magnet

Hanging Installation

1. Fix the Hanging Bar on the Truss

Just turn the Adjusting Screw, to make the Clamps close, the Hanging Bar will be fixed on the Truss safely.

User Manual P12

2. Connect Black Pearl tiles with the hanging bar

①Tiles will be attached to the hanging bar by Magnets automatically.

②Press the red button and lock the tiles by Vertical Connector.

②①

Notes: (For Safety)

Please do this by two persons.

3. Hanging Installation

Tile(2×4)

User Manual P13

Stacking System

Stacking system assembly exploded diagram.

Stacking System Support Components

Major components of the Stacking System support assembly are:

1. Base Bar

2. Base Truss

3. Rear Support Truss

4. Rear Bridge(Half Coupler, Brace Arm, Stacking Connector)

Base Bar

Base Truss

Adjusting Knob

Rear Support Truss

Stacking Connector

Brace Arm

Half Coupler

Safely Clip

Vertical Connector

User Manual P14

Stacking Installation

1. Base Bar connection with Base Truss Connect the Base Bar and Base Truss by Pin and Safely Clip.

2. Rear Support Truss and Rear Bridge installation

Lock of Base Truss

Adjust the Knob and make sure the Base Truss

and Base Bar in same horizontal

Half Coupler and Screw

Knob (Adjusting height)

Universal Adjusting Footpad (Keep the Base Bar always horizontal )

Plate (Fix the Base Truss on the ground )

User Manual P15

3. Tiles Installation

Connect the tiles and Base Bar by Vertical Connector, and Rear Support Truss by Rear bridge.

4. Stacking Installation

Tile(2×6)Accessories Count: Base Bar: 4×0.5m, 1×1m Base Truss: 4 Rear Support Truss: 4 Rear Bridge: 4

Rear Bridge

Vertical Connector

Formula:

Z = 5X /Y(kg)

User Manual P16

1 2 3 4 5 6 7 8 9 1 0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 3 0 1 2 4 6 8 10 1 2 14 16 18 2 0 22 24 26 2 8 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 2 8 16 2 4 32 40 48 5 6 64 72 80 88 96 104 112 120 128 136 144 152 160 168 176 184 192 200 208 216 223 231 239 3 18 36 54 72 90 108 126 144 162 180 198 216 233 251 269 287 305 323 341 359 377 395 413 431 448 466 484 502 520 538 4 32 64 96 1 28 160 192 223 255 287 319 351 383 415 446 478 510 542 574 606 638 669 701 733 765 797 829 861 892 924 956 5 50 100 150 200 249 299 349 399 448 498 548 598 648 6

97 747 797 847 896 946 996 1046 1096 1145 1195 1245 1295 1344 1394 1444 1494 6 72 144 216 287 359 431 502 574 646 717 789 861 932 100 4 1076 1147 1219 1291 1362 1434 1506 1577 1649 1721 1792 1864 1936 2007 2079 2151 7 98 196 293 391 488 586 683 781 879 976 107 4 1171 1269 1366 1464 1561 1659 1757 1854 1952 2049 2147 2244 2342 2439 2537 2635 2732 2830 2927 8 128 255 383 510 638 765 892 102 0 1147 1275 1402 1530 1657 1784 1912 2039 2167 2294 2421 2549 2676 2804 2931 3059 3186 3313 3441 3568 3696 3823 9 162 323 484 646 807 968 112 9 1291 1452 1613 1774 1936 2097 2258 2420 2581 2742 2903 3065 3226 3387 3548 3710 3871 4032 4193 4355 4516 4677 4839

10 200 399 598 797 996 119 5 1394 1593 1792 1991 2191 2390 2589 2788 2987 3186 3385 3584 3783 3982 4182 4381 4580 4779 4978 5177 5376 5575 5774 5973 11 241 482 723 964 120 5 1446 1687 1928 2169 2410 2650 2891 3132 3373 3614 3855 4096 4337 4578 4819 5060 5300 5541 5782 6023 6264 6505 6746 6987 7228 12 287 574 861 114 7 1434 1721 2007 2294 2581 2867 3154 3441 3728 4014 4301

4588 4874 5161 5448 5734 6021 6308 6595 6881 7168 7455 7741 8028 8315 8601

Heigh t Tiles Blac k Pearl

Width Tiles Bla ck Pearl

Black Pearl Ballastconfigurator v1

Global truss ROE version

Table shows ballast in KG per tile width.

Ballast weight calculation for ground support system

Hallen wind:125N/m2

Length factor:2.5

100 cm stacking depth, Length factor is 1,5;

60 cm stacking depth, Length factor is 2,5.

Condition:

A. maximum wind force 8 grade

B. 1.5 times safety parameter

C. 0.6M base bar

Notes:

X for stacking tile quantities(height).

Y for the quantities of base truss. Z means the weight of ballast at the base truss, and X≤8Y. additional stronger truss must be added when(X≥10).

Notes: From a height of 4.0m (8 tiles) an additional 48x3 mm tube should be used to stabilize the truss towers.

LED Tile

Ballast

Stronger Truss

Base Bar

Rear Bridge

Rear Truss

Base Truss

User Manual P17

Physical Connection:

06

Straight Installation

Horizontal connector operation

1. Press the horizontal blue button to loosen the handle.(pic2)

2. Pull the handle to turn the connecting bar.(pic3)

3. Connect two tiles and align them.(pic 4)

4. Push handle back for locking.(pic5)

Vercal connector operaon

2. Press the vertical blue button to loosen the handle.(pic2)

Tiles will be attached together by magnets automatically.(pic1)

3. Pull the handle to turn the connecting bar.(pic3)

4. Connect two tiles and align them.(pic 4)

5. Push handle back for locking.(pic5)

Picture 1 Picture 2 Picture 3 Picture 4 Picture 5

Curve Installation

The range of curve: 0~10°(horizontally inner arc).

Tile(2×4)

M10 Hex Socket head cap screws

Concave Connector

User Manual P18

Notes: To keep the lights which on the edge of the module from damaging, please operate

it as follows.

Stacking Installation

Hanging Installation

The Correct way The Wrong way

The control system of Black Pearl series consist of receiving card and sending card. Receiving card is integrated with LED tiles.

User Manual P19

Control System:

07

Software:

Please read software manual rstly, (download link as below): Http://www.roevisual.com/how-to-make-led-display.

Evision (201000S0007)

Working

v o

ltage

Power

100-240V AC

＜20W

Working temperature

-20°C to 45°C

Input port DVI

Output ports number 4 ports

Communication port USB/RJ45

1920×1080 60Hz

Max.Resolution(Input)

Data transmission port Gigabit Ethernet

Material AL6061

Dimension W480×H45×D240mm

Weight 2.30kg

1. Power switch

2. Number keys

3. LCD screen

4. Function keys

5. Knob

0 1 2 3 4 5 6 7 8 9

Black

DVI HDMI

OK

Esc Fn

Menu

Front

Behind

INPUT 100-240V AC 50/60HZ

PORT 4PORT 3PORT 2PORT 1USB2USB1HDMIDVI

1

6

7

8

9

10

2 3 4 5

Specifications

6. DVI port

7. HDMI port

8. USB port

9. RJ45 data port

10. Power port

Diagram:

Service and Maintenance:

08

Picture 1 Picture 2 Picture 3 Picture 3

Rear Maintenance

Application example

1. A single modules.(Picture 1)

2. Remove the screw in red.(Picture 2)

3. Hold the handle and push the module.(Picture 3)

Maintenance on overall installation, just replace the bad modules.

Easy Maintenance with push-out module and all the modules are the same design.

User Manual P20

User Manual P21

Package

09

Flightcase Dimensions:

8 pcs LED tiles per Flightcase

564.00

1,164.60

722.00

102.00

1,142.00

143.00

835.30

616.60

1,142.00

594.00

21.00

6mm EVA FOAMED TAPES

9 Per cent board

111.50 113.00 113.00 113.00 113.00 113.00 113.00 111.50

10.00

12.00

User Manual P22

ROE Visual Co., LtdROE Visual Europe B.V ROE Visual US, Inc

www.roevisual.com www.roevisual.comwww.roevisual.com

Bldg 7, Zhong Yuntai Industrial Park,

Shiyan Town, Shenzhen, China.

E: roe@roevisual.com T: +86-755-8392 4892 F: +86-755-8392 4891

Zernikelaan 2a,

9351VA Leek, The Netherlands.

E: europe@roevisual.com

T: +31 (0) 50 211 0990

2514 N, Naomi Street,

Burbank, CA, 91504

E: usa@roevisual.com

T: +1 747 229 9190

ROE BP2, BP3, BP5 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual