How it Works
ROE
Loading...
Air Frame
User Manual
20 pgs3.46 Mb0

ROE Air Frame User Manual

Download
Air Frame User Manual
Manual No. AF-180709 Version: 1.0 Updated: 9, July 2018.
1
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of ROE.
Warranty Policy
ROE Visual Co., Ltd. is pleased to offer a 2-year warranty on all standard products① against manufacturers defects, covering parts and labors. ROE will provide both factory and on-site technical
support when necessary during the warranty period. Following cases are not included:
1. If replacement parts required, customers should ship defective parts at their cost. ROE will ship replacement parts at our cost, during the warranty period.
2. In terms of customized products② and/or systems③, every order will be clearly specified in the contract and will be handled on an individual basis.
3. After the 2-year warranty, customers should bear charges of service and/or repair in accordance with the industrial standard.
4. The warranty will be void as follows: (1) Accidents or human error. (2) Any modification, disassembly, repair, maintenance or testing unauthorized by ROE. (3) Product series number is broken, including SN, ESN, MEID, and IMEI. (4) Gross negligence.
Notes:
① Standard products refer to products officially launched by ROE. ② Customized products refer to ROE standard products which are partially or totally designed in line
with customers’ requirements and demands.
③ Customized systems refer to products with special systems required by customers.
2
Contents
1. Safety Information ........................................................................................................................................ 3
2. Usage ............................................................................................................................................................. 4
2.1 Frame and Bracing ................................................................................................................................ 4
2.2 Side Lock ................................................................................................................................................. 6
2.3 Bottom Lock ............................................................................................................................................ 7
2.4 Alternative Bracing ................................................................................................................................. 8
2.5 Position Ladder ....................................................................................................................................... 9
2.5.1 Bracing Position .............................................................................................................................. 9
2.5.2 Transport Position ......................................................................................................................... 10
3. Stacking System ......................................................................................................................................... 11
4. Rigging System ........................................................................................................................................... 12
5. Safety during Cabling ................................................................................................................................ 13
6. Brackets ....................................................................................................................................................... 14
6.1 Hanging Bracket ................................................................................................................................... 14
6.2 Coupler Bracket .................................................................................................................................... 14
7. Dolly and Storage ....................................................................................................................................... 15
8. Storage and Truck Pack ............................................................................................................................ 16
9. Parts ............................................................................................................................................................. 17
10. Contact Information .................................................................................................................................. 19
3
1. Safety Information
This product is for professional use only. It is not for household use.
This product presents risk of severe injury if not used in the correct way.
Before use, always visually inspect for damage. Do not use if damage is found.
Do not use any abrasive or corrosive products to clean any of the carbon parts.
Do not use any clamps on the carbon parts.
Do not use tools to open/close the locks.
Read this manual before installing or servicing this product.
Follow safety precautions listed below and observe all warnings in this manual and printed on the product.
No magnesium alloy is used in this frame
All carbon fiber used is fire retardant.
4
2. Usage
2.1 Frame and Bracing
Open Bracing position
Total depth: 448mm
Closed Bracing position
Total depth: 120mm
Clamps are opened and closed using the red actuator.
Arms need to be positioned according to the desired configuration. (bracing or transport)
A transport lock is foreseen on the carbon frame tube.
A red actuator is used to unlock.
5
To lock the bracing, move part A upwards and rotate clockwise until part A is locked into part B.
To unlock the bracing, move part B upwards and rotate part A counterclockwise.
Locked position
6
2.2 Side Lock
The frame can be put in a +10 / +5 / 0 / -5 / -10 degree position.
Also, any angle between +10 and -10 can be achieved by just tightening A to the correct position.
To achieve this, part A needs to be loosened by turning 90 degrees away from the tile.
Pull part B and position part C in the desired position. Retighten part A.
Push lever D to unlock.
Always put locking handle D and latch E in this position for transport, to prevent damage to the next tile in the dolly.
E
D
A
B
C
7
2.3 Bottom Lock
The red levers need to be pulled backwards and moved sideways (outwards) to lock frames top to bottom.
Make sure the red markings are not visible, otherwise frames are not locked.
8
2.4 Alternative Bracing
A keyhole lock is provided to connect with ROE standard rear bridge stacking accessory.
Placing clamps on the carbon parts is not allowed. To accommodate for this, a ring is positioned on the bracing’s upright. This ring can take standard clamps for 48-51mm tubing.
Baby arm clamps to upright part
9
2.5 Position Ladder
2.5.1 B racing Position
Click the arm in the top slots.
Bracing ladder is placed between frames. To install, click ladder clamps in
Only use the steps in the ladder to climb the LED wall.
10
2.5.2 Transport Position
Click arm in closed position
To put in transport position, click ladder clamps in the 3 slots.
11
3. Stacking System
Bracing can also be used in a stacking configuration.
+10, 0. -10 degree
Angle is set with both side locks and base stands.
Height is set with adjustment rings.
12
4. Rigging System
Allowable wind [m/s] / height
Height
Max. allowable (3-sec gust) [m/s]
Height
Max. allowable (3-sec gust) [m/s]
10 frames
20.00
6 frames
21.71
8 frames
20.76
5 frames
22.98
Load type
Bracket
Max height
[#frames]
Max height
[m]
Limiting
factor
Only self-weight
Any
25
30
Kingpin
Self-weight + climbing
Any
21
25.2
Kingpin
Self-weight, climbing, falling
Any
21
25.2
Kingpin
Bracing at the bottom
13
5. Safety during Cabling
Connection point for safety hook.
Where ladder and bracing arm connect.
14
6. Brackets
6.1 Hanging Bracket
6.2 Coupler Bracket
The coupler bracket can only be used with the 2 wide hanging brackets.
To install, the shackles on the header bars need to be removed.
The coupler bracket is connected to the existing center pickup holes with locking pins.
Unlocked position
Locked position
15
7. Dolly and Storage
LED should always face inside!
1537mm high
Double stacked dollies are only for storage.
Max 2 high stack. Wheels get damaged if higher.
2862mm high
2629mm high
Pay attention when moving double stacked frames up a ramp.
See safety label on the dolly!
16
8. Storage and Truck Pack
For storage on site, the stackers can also be used to neatly stack the dolly floors.
Side covers can be stored on an empty dolly floor.
EU mega box trailer 44 dollies, frames double stacked Or
506.88 sqm
53’ US truck 48 dollies frames double stacked Or
552.96 sqm
17
9. Parts
1-Wide bracket: 6.4kg 2-Wide bracket: 12.6kg
Coupler bracket: 30kg
Full Frame
1200 x 600mm 8 kg
Full bracing
4.2 kg
Half Frame
600 x 600mm
5.2 kg
Half bracing
2.5 kg
18
Full dolly:
1150 x 1277 x 1537mm (with stackers) 504kg
1150 x 1277 x 1429mm (no stackers) 490kg
Empty dolly: 85kg
Dolly Stackers:14kg/set
Baby arm:
640 x 50 x 60mm
0.875kg
Stacker base truss:
680 x 463 x 184mm
12.55kg
1W base stand:
600 x 180 x 180mm
6.8kg
19
10. Contact Information
If you have any questions about the User Manual, please feel free to contact with ROE technical service team.
ROE China
ROE Visual Co., Ltd. No.3 Floor, Build 7, Zhong Yun Tai Technology Industrial Park, Baoan District, Shenzhen, China, 518108 Tel: +86-755-83924892 Fax: +86-755-83924891 Email: service@roevisual.com
ROE Europe
ROE Visual Europe BV Office: Zernikelaan 2a, 9351 VA Leek, The Netherlands Warehouse: Industriepark 9a, 9351 PA Leek, The Netherlands Tel: +31 (0) 50 211 0990 Email: europe@roevisual.com
ROE America
ROE Visual US, Inc 2514 N Naomi Street, Burbank, CA 91504 Tel: +1 747 229 9190 Email: usa@roevisual.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use