Rockwell Automation TLP-SSN-F115, TLP-SSN-F090, TLP-SSN-F046, TLP-SSN-F070, TLP-SSN-F200 Installation Instructions Manual

...
Page 1
Installation Instructions
Original Instructions

Shaft Seal Kits for Kinetix TLP Servo Motors

Catalog Numbers
TLP-SSN-F046, TLP-SSN-F070, TLP-SSN-F090, TLP-SSN-F100, TLP-SSN-F115,
TLP-SSN-F145, TLP-SSN-F200, TLP-SSN-F235
Topic Page
About Shaft Seals 2
Required Supplies 2
Remove the Shaft Seal 3
Replace the Shaft Seal 4
Shaft Seal Kit Catalog Numbers 6
Additional Resources 7
Page 2
Shaft Seal Kits for Kinetix TLP Servo Motors
Oil, Fluids, and Fine Dust
Oil, Flui ds, and Fine Dus t
Shaft Seal Installations Recommended
Shaft Seal Installation is Not Recommended
Motor Shaft and End Bell are Exposed to Containments
Motor Shaft and End Bell are Protected From Containments
Shaft Seal Installation is Not Recommended

About Shaft Seals

A shaft seal is recommended if the motor shaft and end bell are exposed to significant amounts of containments, such as oil, fluids, or fine dust. Use a shaft seal in these environments to prolong the life of the motor. A shaft seal and Bulletin 2090 cables with environmentally sealed connectors are required for an IP65 rating or greater.
See Kinetix® Motion Accessories Specifications Technical Data, publication KNX-TD004 find Bulletin 2090 cables with environmentally sealed connectors for your motor.
IMPORTANT The shaft seal is not required in applications where the motor shaft and end bell are free of oil,
fluids, or fine dust, and a lower IP rating is sufficient.
Shaft seals are subject to wear and require periodic inspection and replacement. Replacement is recommended every 3 months, not to exceed 12 months, depending on use.
If you paint the motor, do not get paint on the shaft seal area or the shaft, as paint can decrease the life of the shaft seal.
, to

Required Tools

Use these tools to install a shaft seal:
• Insulated, small, flat-head screw driver
• Rubber/wooden mallet or a metal hammer and wooden work piece
• Socket, pipe, or tube (various sizes)
• Abrasive cloth to remove any nicks or burrs from the motor shaft

Required Supplies

Lubricant - Grease, industrial grade, suitable for applications with speeds up to 6000 RPM, and –10…+80 °C (14…176 °F) temperature range.
2 Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Page 3
Shaft Seal Kits for Kinetix TLP Servo Motors
Do not re move screws.
Do not pry against front-end bell or shaft.
Outer Lip

Remove the Shaft Seal

ATTENTION: To avoid injury or damage to the equipment, remove power from the motor before
removing the shaft seal.
Follow these steps to remove the shaft seal.
1. Remove power to the motor before removing the shaft seal.
2. Remove the shaft key (if present) from the motor shaft.
3. Remove old seal.
Place the insulated screw driver on the inside diameter of the shaft seal outer lip as shown. Carefully lift the seal, work your way around the seal lift a little at a time. When you can grasp the seal, slightly rotate it while pulling it out of the front-end bell.
ATT EN TI ON : Avoid damage to the motor. Do not pry against front-end bell or shaft.
ATTENTION: Do not hammer the shaft or body of the motor when changing the shaft seal.
4. Inspect and clean the shaft and seal surfaces as necessary.
Use an abrasive cloth to remove any nicks or burrs from the motor shaft.
Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 3
Page 4
Shaft Seal Kits for Kinetix TLP Servo Motors
Back View of Shaft Seal
(motor facing)
Inner Shaft Seal Lip
Inner Shaft Seal Lip
Outer Shaft Seal Lip

Replace the Shaft Seal

Follow these steps to replace the shaft seal.
1. Apply tape to the keyway so the edges do not damage the seal lip.
IMPORTANT Cover the sharp edges of the keyway with tape to protect the shaft seal lip from
damage.
2. Lubricate the motor shaft and the inner and outer lip of the shaft seal.
IMPORTANT Shaft seals require a lubricant to reduce wear. Lubricate only the inner and outer lip
of the shaft seal. Do not lubricate the motor bore or outside diameter of the seal.
3. Center the shaft seal on the mounting surface of the motor and slide the shaft seal evenly onto the motor shaft.
See Shaft Seal Installation Clearances the shaft seal you are installing.
4. Press the shaft seal into the seal bore by applying one of the Shaft Seal Installation
Methods on page 6.
5. Visually inspect for irregularities in the shaft seal or an uneven alignment where the shaft seal contacts the motor.
Verify that the outer and inner circumference of the shaft seal is fully seated into position.
6. Verify that the shaft seal is installed to the correct installation clearance.
• If the shaft seal is installed too deep, it can become subject to excessive wear and
require frequent replacement.
• If the shaft seal is installed too shallow, it can reduce the effectiveness of the
protective seal.
7. Replace the shaft key.
Applies to motors that include a keyed shaft.
on page 5 for the correct installation clearance of
4 Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Page 5
Shaft Seal Installation Clearances
Front Sur face of Motor
Shaft Seal Pressed Flush with Front Surface of Motor
Shaft Seal Pressed Below Front Surface of Motor
Front Sur face of Motor
Nom
Min
Max
Bulletin TLP-A0xx
Shaft Seal Example
Bulletin TLP-A1xx and TLP-A2xx
Shaft Seal Example
Shaft Seal
Shaft
Shaft Seal
Shaft Seal Kits for Kinetix TLP Servo Motors
Motor Cat. No.
TLP-A0xx Press the shaft seal so that the seal is flush with the front surface of the motor.
TLP-A1xx and TLP-A2xx 0.00 (0.00) 0.10 (0.004) 0.20 (0.008)
Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 5
Min, mm (in.) Nom, mm (in.) Max, mm (in.)
Shaft Seal Installation Clearance
Page 6
Shaft Seal Kits for Kinetix TLP Servo Motors
Socket, Pipe, or Tube (supplied by the customer)
Motor
Metal
Hammer
Shaft Seal
Wooden
Work Piece
Rubber or
Wooden Mallet
Motor
Shaft Seal
Socket, Pipe, or Tube (supplied by the customer)
Or

Shaft Seal Installation Methods

ATT EN TI ON : Do not hammer directly on the shaft seal. Gently tap the socket, pipe, or tube evenly
around the outer edge of the shaft seal until the shaft seal is pressed into place. Make sure the socket, pipe, or tube you use does not contact the shaft seal lip. Permanent damage to the shaft seal can occur.

Shaft Seal Kit Catalog Numbers

IMPORTANT Third-party shaft seals are not approved for use with these motors. The use of third-party shaft
seals voids any implied or expressed warranties.
Kinetix TLP Low Inertia Motors
Motor Cat. No. Shaft Seal Kit Cat. No.
TPL-A046 TLP-SSN-F046
TPL-A070 TLP-SSN-F070
TPL-A090 TLP-SSN-F090
TPL-A100 TLP-SSN-F100
TPL-A115 TLP-SSN-F115
TPL-A145 TLP-SSN-F145
TPL-A200 TLP-SSN-F200
TPL-A235 TLP-SSN-F235
6 Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Page 7
Shaft Seal Kits for Kinetix TLP Servo Motors

Additional Resources

These documents contain additional information concerning related products from Rockwell Automation.
Resource Description
Kinetix Rotary Motion Specifications Technical Data, publication KNX-TD001
Kinetix Motion Accessories Specifications Technical Data, publication KNX-TD004
Kinetix Motion Control Selection Guide, publication KNX-SG001
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Product Certifications website, rok.auto/certifications
You can view or download publications at http://www.rockwellautomation.com/global/
literature-library/overview.page.
Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPH, VPS), MP-Series™ (Bulletin MPL, MPM, MPF, MPS), and TL-Series™ rotar y motors.
Product specifications for Bulletin 2090 motor and interface cables, low-profile connector kits, drive power components, and other servo drive accessory items.
Overview of Kinetix servo drives, motors, actuators, and motion accessories that are designed to help make initial decisions for the motion control products best suited for your system requirements.
Provides general guidelines for installing a Rockwell Automation industrial system.
Provides declarations of conformity, certificates, and other certification details.
Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 7
Page 8
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
5014099301-QO01
*QO01*
Rockwell Automation Support
Use the following resources to access support information.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the How Are We Doing? form at http://
literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Technical Support Center
Knowledgebase Articles, How-to Videos, FAQs, Chat, User Forums, and Product Notification Updates.
https://rockwellautomation.custhelp.com/
Local Technical Support Phone Numbers
Locate the phone number for your country.
http://www.rockwellautomation.com/global/support/get-support­now.page
Direct Dial Codes
Find the Direct Dial Code for your product. Use the code to route your call directly to a technic al support engineer.
http://www.rockwellautomation.com/global/support/direct-dial.page
Literature Library
Installation Instructions, Manuals, Brochures, and Technical Data.
http://www.rockwellautomation.com/global/literature-library/ overview.page
Product Compatibility and Download Center (PCDC)
Get help determining how products interact, check features and capabilities, and find associated firmware.
http://www.rockwellautomation.com/global/support/pcdc.page
Rockwell Automation maintains current product environmental information on its webs ite at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
Allen-Bradley, Kinetix, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 2090-IN044B-EN-P - September 2019
Supersedes Publication 2090-IN044A-EN-P - September 2019 Copyright © 2019 Rockwell Automation, Inc. All rights reser ved. Printed in the U.S.A.
.
Loading...