![](/html/9f/9f8b/9f8bde14ec08fb5ea0dafc8fc70b4d1d99f33c55b001df92143575b91815538b/bg1.png)
SDS-8297
TM
Trusted
Industrial Control System
TrustedTM Output Power Distribution Unit(Diode Protected)-T8297
GENERAL ASSEMBLY
FEATURES
Supports up to three
Trusted
modules
Dual stud power
connection for either single
or dual feed
On-board common cathode
diodes for dual dc feeds
(AO or low current DO only)
TM
sourcing output
DESCRIPTION
The Trusted
24-120V dc for use with Trusted
T8471, 24V dc and 120V dc Digital Output Modules respectively, and T848X
Analogue Output Modules obtaining their 0V reference via Trusted
Versatile Field Termination Assemblies (VFTAs).
The Unit is designed to be mounted on a DIN rail above the relevant output
module I/O connectors.
The Trusted
+ve field loop power for the 24-120V dc range of Trusted
modules. The output 0V reference and 0V power return is via the Trusted
Versatile Field Termination Assemble (VFTA).
Up to three output modules may be supported providing the total load does
not exceed the maximum rated capacity of the Unit.
Each supply stud is capable is capable of supplying the maximum rated
capacity and can be used in single or dual configuration as required. Dual
configuration may be used where the supply is fed via blocking diodes.
Where the total load current for three Trusted
Modules is less than 6A, the supply can be fed via the on-board blocking
diodes through terminal block TB1. If this method of supply is used,
insulating sleeves must be fitted to the redundant power studs.
TM
Output Power Distribution Unit is designed to provide
TM
Output Power Distribution Unit is designed to distribute the
TM
sourcing output modules, e.g. T8451 and
TM
sourcing output
TM
Analogue or Digital Output
TM
TM
Issue 5 Jan 2006
![](/html/9f/9f8b/9f8bde14ec08fb5ea0dafc8fc70b4d1d99f33c55b001df92143575b91815538b/bg2.png)
SDS-8297
Trusted
TM
Industrial Control System
TrustedTM Output Power Distribution Unit (Diode Protected)-T8297
BLOCK DIAGRAM
ELECTRICAL SPECIFICATION
Voltage Range
Supply Current (via studs)
Supply Current (via TB1)
Supply Connection +ve (stud)
Supply Connection +ve (TB1)
Power Output (3-off)
Conductor Clamping Range
0 to 140V dc
65A max
6A max
2-off M6 x 25mm studs
BLZ 2-part terminal
6-way AMP MATE-N-LOK connector
0.5 to 2.5mm
2
MECHANICAL
SPECIFICATION
Dimensions (HxWxD):
70mm x 90mm x 50mm
(2.75ins x 3.54ins x
1.97ins)
Weight (fully populated)
100gms
(0.22lbs)
ENVIRONMENTAL
Operating Temperature:
-5°C to 60°C
(23°F to 140°F)
Operating Humidity:
5 to 95%, noncondensing
Vibration:
10 to 57Hz ±0.075mm
57 to 150Hz 1.0g
Shock:
15g, ½ sine wave, 11ms
EMI (IEC 801):
ESD
Air discharge to 15kV.
Contact discharge to 8kV
Radiated Fields
10V/m, 27MHz to
500MHz
Transients and Bursts
2kV, 2.5kHz for
t=60 seconds
ICS Triplex
Technical data sheets are intended for
information and guidance. The Company
has a policy of continual product
development and improvement.
Specifications are subject to change
without notice or latest information, visit our
Website:- www.icstri plex.c om