Page 1
1
3
2
6
5
1
1
1
6
4
3
2
1
1.Lever (2pcs)
2.Set screw (2pcs)
3.Plastic washer (2pcs)
4.INTERNAL BACKPLATE(1pc)
5.# 10-24x1-3/4" Flat head machine
screw(2pcs)
6.Adaptor (2pcs)
7.EXTERNAL BACKPLATE(1pc)
8.Turn piece mounting plate (1pc)
9.#10-32x2" pan head machine
screw (2pcs)
10.Spindle (1pc)
11.#8-32x7/8" oval head machine
screw (2pcs)
12. #8 x 7/8" Tapping screw(1pc)
BEFORE YOU BEGIN
Check door thickness as handle will work with a 1-
3
4
" thick door only. If door thickness is greater than 13
4
" up to 2-
1
4
" thick please contact Rockwell
Security Inc.
Remove and discard all packaging materials and
verify you have all the parts in the exploded view
section of instructions
Follow step by step installation instructions to
ensure proper operation of handle set.
Always wear protective eyewear.
(2) MOUNTING PLATE SCREW
#10-24UNC x1-
3
4
"
(2) DEADBOLT MOUNTING SCREW
#10-32 x 2"
INSTALLATION FASTENERS
(1) TAPPING SCREW
#8 x 7/8"
(2)MOUNTING PLATE
SCREW, #8-32 UNC 7/8"
1. Using a philipps screwdriver extend the
deadbolt of the MP lock by inserting into the
Cross Slot on the top hole and
turning 90 degrees
Extend
deadbolt
2. From the inside of the door insert the the spindle in the direction of the ARROW through the
square hole on the latch, ensuring the groove side of th spindle is facing down. Slide the spindle
through the latch until the stops of the spindle make contact with the hub.
INSIDE
SPINDLE
GROOVE SIDE
FACING DOWN
STOPS ON
SPINDLE
(2) SET SCREW
1/4"-20
TM
Rockwell
ENTRY HANDLE
SET INSTALLATION
INSTRUCTIONS
H435
REQUIRED TOOLS
Protective Eyewear
#2 Phillips Screwdriver
Extend
deadbolt
86MPMEN913 Rev. A1/2
Page 2
3. From the Outside, Install the Outside
Mounting Plate and from the inside install the
Internal Mounting Plate. Secure the mounting
plates in place using the 2 mounting screws.
Note, Inside mounting plate has 2 Countersink
holes to receive the mounting screws. DO NOT
OVERTIGHTEN SCREWS.
COUNTERSUNK
HOLES
Thumbturn
Horizontal
Plastic Washers
already preinstalled.
6. Plastic washers are already
preinstalled on the levers. Place the
plastic washer on the shank of the
knob or lever. Spare washer is also
packed
4. From the inside of the door orient the turn piece
mounting plate and secure by inserting the two
deadbolt mounting screws through the turn piece
mounting plate, lock, and into the cylinder housing.
Only after installation test the deadbolt by locking
and unlocking the deadbolt with the key. If the
deadbolt does not lock or unlock refer to the trouble
shooting guide.
5. Position the interior trim over
the mounting plate and insert the
cylinder tailpiece into the
thumbturn of the interior trim.
PROBLEM
Can't extend (lock) deadbolt unless key is in cylinder. Can't
remove key from cylinder when the deadbolt is extended (locked).
Knob or lever keeps coming off the spindle
Deadbolt can easily be locked using the interior plate assembly on
the inside but is difficult to lock when locked with the key from the
outside.
Cannot extend deadbolt with the interior plate assembly or key
when door is closed.
TROUBLE SHOOTING GUIDE
SOLUTION
Cylinder tailpiece is not oriented properly. Remove the cylinder by first removing the turnpiece trim, and
turnpiece mounting plate. Rotate the cylinder tailpiece vertical with the deadbolt extended and reinstall
the deadbolt assembly. Refer to steps 5 through 7
Ensure the spindle is oriented with the groove facing down and the set screw is securely tightened. Refer
to step 2.
The cylinder is not properly aligned with the interior plate assembly or improper door thickness. Remove
the internal plate assembly and loosen the two mounting plate screws. Align the cylinder and re-tighten
the deadbolt mounting screws. Ensure your door thickness is at least 1-3/4" thick. Please ensure to
check the cylinder tailpiece is oriented correctly.
Open door and try to extend deadbolt. If deadbolt extends easily with the door open then the strikes are
not aligned with the deadbolt and/or locking points. Adjust the strike to align with the deadbolt and/or
locking points. Ensure the strike hole is deep enough for the deadbolt to engage.
7. Press the lever snugly against the interior trim assembly and tighten the set
screw with the provided Allen wrench. While pushing on the internal lever, push
the external lever into the external side of the door and tighten the set screw.
Note: Set screw should be flush on the handle upon installation. If not,
please check orientation of the spindle shaft.
VERTICAL
TAILPIECE
Extend
deadbolt
Extend
deadbolt
Extend
deadbolt
Extend
deadbolt
CORRECT
ORIENTATION
ATTACH
BOTTOM
SCREW
86MPMEN913 Rev. A2/2
Do not insert key
during this step.
Loading...