Rockwell 1732DS-IB8XOBV4, 1732DS-IB8 Installation Instructions Manual

Installation Instructions

ArmorBlock Guard I/O DeviceNet Safety
Modules

Catalog Numbers 1732DS-IB8XOBV4, 1732DS-IB8

Topic Page

Important User Information 2
Environment and Enclosure 3
Preventing Electrostatic Discharge 4
Before You Begin 5
Module Identification and Dimensions 5
Observing Precautions for Correct Use 7
Observing Precautions for Safe Use 7
Install the Module 10
Set MAC ID 10
Wiring the Module 10
Working with I/O Connectors 11
Terminal Positions 12
Interpret the Status Indicators 14
Specifications 18
Additional Resources 23

2 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls
(Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/

) describes some important differences between solid
state equipment and hard-wired electromechanical devices. Because of this difference, and also
because of the wide variety of uses for solid state equipment, all persons responsible for applying this
equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular installation, Rockwell Automation, Inc.
cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of
the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal
injury or death, property damage, or economic loss. Attentions help you identify a
hazard, avoid a hazard and recognize the consequences.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.

SHOCK HAZARD

BURN HAZARD

ArmorBlock Guard I/O DeviceNet Safety Modules 3

Publication

1732DS-IN001D-EN-P - September 2009

Environment and Enclosure

ATTENTION

This equipment is intended for use in overvoltage Category II
applications (as defined in IEC 60664-1), at altitudes up to 2000 m
(6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment
according to IEC/CISPR Publication 11. Without appropriate
precautions, there may be potential difficulties with electromagnetic
compatibility in residential and other environments due to conducted
and radiated disturbances.

This equipment is supplied as enclosed equipment. It should not
require additional system enclosure when used in locations
consistent with the enclosure type ratings stated in the Specifications
section of this publication. Subsequent sections of this publication
may contain additional information regarding specific enclosure type
ratings, beyond what this product provides, that are required to
comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, for
additional installation requirements, publication 1770-4.1

.

• NEMA Standards 250 and IEC 60529, as applicable, for
explanations of the degrees of protection provided by different
types of enclosure.

4 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Preventing Electrostatic Discharge

ATTENTION

This equipment is sensitive to electrostatic discharge, which can
cause internal damage and affect normal operation. Follow these
guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION

Make sure all connectors and caps are securely tightened to properly
seal the connections against leaks and maintain IP enclosure type
requirements.

Personnel responsible for the application of safety-related
Programmable Electronic Systems (PES) shall be aware of the safety
requirements in the application of the system and shall be trained in
using the system.

If the devices (sensors) connected to the input connections require
Class 2 power to operate, the auxiliary power connections of this
equipment must be powered by a Class 2 source.
To comply with the CE low-voltage directive (LVD), this equipment and
all connected I/O must be powered from a source compliant with the
following: safety extra low voltage (SELV) or protected extra low
voltage (PELV).

ArmorBlock Guard I/O DeviceNet Safety Modules 5

Publication

1732DS-IN001D-EN-P - September 2009

Before You Begin

Before installing and operating the product, read these installation
instructions to learn important installation-related information and the
precautions to follow as you install and operate the product. Keep these
instructions for future reference.

Concerning suitability for use, note that we are not responsible for conformity
with any standards, codes, or regulations that apply to the combination of the
products in your application or use of the product. Take all necessary steps to
determine the suitability of the product for the systems, machines, and
equipment with which it will be used. Know and observe all prohibitions of
use applicable to this product.

Never use the products for an application involving serious risk to life or
property without first verifying that the system as a whole has been designed
to address the risks and that the Rockwell Automation product is properly
rated and installed for the intended use within the overall equipment or
system.

Module Identification and Dimensions

See the table for identification information and figures for module
dimensions.

Module Identification

Cat. No. Name Safety

Inputs

Tes t
Outputs

(1)

(1)

Each test output can be set to function as a pulse test output or a standard output pulse.
Test outputs are used in combination with a safety input. Broken wires in an external
indicator can be detected for terminal T3 and T7 only.

Safety Outputs

1732DS-IB8 Safety input module 8 8 ­1732DS-IB8XOBV4 Safety I/O module with

solid state outputs

8 8 4 bipolar pairs

6 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

1732DS-IB8XOBV4 Module Dimensions

1732DS-IB8 Module Dimensions

31626

179 mm (7.05 in.)

70 mm (2.76 in.)

168.6 mm (6.64 in.)

68.7 mm
(2.71 in.)

179 mm (7.05 in.)

70 mm (2.76 in.)

168.6 mm (6.64 in.)

68.7 mm
(2.71 in.)

31627

ArmorBlock Guard I/O DeviceNet Safety Modules 7

Publication

1732DS-IN001D-EN-P - September 2009

Observing Precautions for Correct Use

Read this for information related to operating directions after reading the
Guard I/O DeviceNet Safety User Manual, publication 1791DS-UM001.

Do not use the unit in locations subject to the following:

• Direct sunlight

• Temperatures or humidity beyond the ranges noted in the

Specifications section

• Corrosive or flammable gases

• Shock or vibration beyond the range noted in the Specifications

section

Observing Precautions for Safe Use

Read this list of precautions for safe use.

• Wire conductors correctly and verify operation of the module before
commissioning the system in which the module is incorporated,
noting that incorrect wiring can lead to loss of safety function.

• Do not apply DC voltages exceeding rated voltages to the module.

• Apply properly specified voltages to the module inputs. Note that

applying inappropriate voltages causes the module to fail to perform
its specified function, which leads to loss of safety functions or
damage to the module.

• Do not use test outputs as any safety output. Test outputs are not
safety outputs.

• Be sure that qualified personnel confirm installation and conduct test
operations and maintenance after installation of the module.

• Be sure that personnel familiar with machinery where the module is to
be installed should conduct and verify installation.

• Do not dismantle, repair, or modify the module. This can lead to loss
of its safety function.

8 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

• Use only appropriate components or devices complying with relevant
safety standards corresponding to the required level of safety
categories (safety integrity level). Conformity to requirements of
safety category (safety integrity level) is determined as an entire
system. We recommend you consult a certification body regarding
assessment of conformity to required safety level.

• You are responsible for compliance with applicable standards for the
entire system.

• Disconnect the module from the power supply when wiring.

ATTENTION

Safety state of the module and its data is defined as off state.

Serious injury can occur due to breakdown of safety outputs. Do not
connect loads beyond the rated value of the safety outputs.

Serious injury can occur due to loss of required safety functions. Wire
the module properly so that supply voltages or voltages for loads do
not touch the safety outputs accidentally or unintentionally.

As serious injury can occur due to loss of safety functions, use
appropriate devices as shown in the Controlling Devices - Sample

Requirements table.

ArmorBlock Guard I/O DeviceNet Safety Modules 9

Publication

1732DS-IN001D-EN-P - September 2009

Controlling Devices - Sample Requirements

Device Requirement Allen-Bradley Bulletin

Safety Components

Emergency
stop switch

Use approved devices with direct opening
mechanism complying with IEC/EN
60947-5-1.

Bulletin 800F, 800T

Door
interlocking
switch
limit switch

Use approved devices with direct opening
mechanism complying with IEC/EN
60947-5-1 and capable of switching
microloads of 24V DC 5 mA.

Bulletin 440K, 440G, or
440H for interlock switch,
Bulletin 440P or 802T for
limit switch

Safety sensor Use approved devices complying with the

relevant product standards, regulations, and
rules in the country where used.

Any Allen-Bradley
Guardmaster product

Relay with
forcibly guided
contacts

Use approved devices with forcibly guided
contacts complying with EN 50205. For
feedback purposes, use devices with
contacts capable of switching micro loads of
24V DC 5 mA.

Bulletin 700S, 100S

Other devices Evaluate whether devices used are

appropriate to satisfy requirements of safety
category levels.

None

10 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Install the Module

Read this section for installation-related information.

Set MAC ID

Set the MAC ID by using the rotary switches. The MAC ID is set to 63 by
default.

Wiring the Module

Follow these guidelines when wiring the module:

• Do not share communication, input, or output lines with high voltage,
referring to Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1

.

• Wire correctly after confirming the signal names of all terminals.

• Follow wiring and installation guidelines for DeviceNet networks and

be sure that you:

• do not exceed a drop length of 5.7 m (19 ft).

• note that the total drop length budget for the network is reduced

by 0.30 m (1 ft) for each 1732DS module.

|

|

|

|

|

2

4

6

8

0

|

|

|

|

|

2

4

6

8

0

X1X10

ArmorBlock Guard I/O DeviceNet Safety Modules 11

Publication

1732DS-IN001D-EN-P - September 2009

Working with I/O Connectors

See the figure that shows connectors. The modules have M12 female I/O
connectors.

Input and Output Configuration

Input Configuration

Pin Signal

1 Test Output n+1

2 Safe Input n+1

3 Input Common

4 Safe Input n

5 Test Output n

Output Configuration
(1732DS-IB8XOBV4
module only)

Pin Signal

1 Output +24V DC Power

2 Output n+1

(Sinking/Switch 24V DC Common)

3 Output Power Common

4 Output n (Sourcing/Switch 24V DC)

5 Output Power Common

44042

12 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

The modules have mini-sealed DeviceNet In (male) and DeviceNet Out
(female) connectors for daisy-chaining and a mini-sealed Power Output (male)
connector.

DeviceNet and Power Configuration

Terminal Positions

See the figure and table that show terminal positions.

DeviceNet Male and
Female Configuration

Pin Signal

1Drain

2V+

3V-

4CAN-H

5CAN_L

Power Configuration

Pin Signal

1

Output +24V DC Power

(1)

(1)

1732DS-IB8XOBV4 module only.

2 Input +24V DC Power

3 Input Power Common

4

Output Power Common

(1)

44040

44043

Male

Female

Male

44044

44121

ADBC

EHFG

ArmorBlock Guard I/O DeviceNet Safety Modules 13

Publication

1732DS-IN001D-EN-P - September 2009

Terminal Positions

1732DS-IB8XOBV4 and
1732DS-IB8 Modules

1732DS-IB8XOBV4 Module Only

A-1 Test Output 1 E-1

S+/24V DC

(1)

(1)

S+ denotes output return +24V DC.

A-2 Safety Input 1 E-2

Safety Output 1

(2)

(Switch 24V DC Common)

(2)

Safety outputs can be used only as pairs. Safety outputs 0/1, 2/3, 4/5, and 6/7 must be controlled as
a pair.

A-3 Input Common E-3

L-/24V DC Common

(3)

(3)

L- denotes output return common.

A-4 Safety Input 0 E-4

Safety Output 0

(2)

(Switch 24V DC)

A-5 Test Output 0 E-5

L-/24V DC Common

(3)

B-1 Test Output 3 F-1

S+/24V DC

(1)

B-2 Safety Input 3 F-2

Safety Output 3

(2)

(Switch 24V DC Common)

B-3 Input Common F-3

L-/24V DC Common

(3)

B-4 Safety Input 2 F-4

Safety Output 2

(2)

(Switch 24V DC)

B-5 Test Output 2 F-5

L-/24V DC Common

(3)

C-1 Test Output 5 G-1

S+/24V DC

(1)

C-2 Safety Input 5 G-2

Safety Output 5

(2)

(Switch 24V DC Common)

C-3 Input Common G-3

L-/24V DC Common

(3)

C-4 Safety Input 4 G-4

Safety Output 4

(2)

(Switch 24V DC)

C-5 Test Output 4 G-5

L-/24V DC Common

(3)

D-1 Test Output 7 H-1

S+/24V DC

(1)

D-2 Safety Input 7 H-2

Safety Output 7

(2)

(Switch 24V DC Common)

D-3 Input Common H-3

L-/24V DC Common

(3)

D-4 Safety Input 6 H-4

Safety Output 6

(2)

(Switch 24V DC)

D-5 Test Output 6 H-5

L-/24V DC Common

(3)

14 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Interpret the Status Indicators

See the tables for information about how to interpret status indicators.

24V DC Input Power Indicator

State Status Description Recommended Action

Off No power No power is applied. Apply power to this section.
Solid

green

Normal
operation

The applied voltage is
within specifications.

None.

Solid
yellow

Input power
out of
specification

The input power is out of
specification.

Check your configuration,
wiring, and voltages and apply
the changes.

24V DC Output Power Indicator (1732DS-IB8XOBV4 module only)

State Status Description Recommended Action

Off No power No power is applied. Apply power to this section.
Solid

green

Normal
operation

The applied voltage is
within specifications.

None.

Solid
yellow

Output power
out of
specification

The output power is out
of specification.

Check your configuration,
wiring, and voltages and
apply the changes.

Module Status Indicator

(1)

State Status Description

Off No power or autobauding No power is applied to the

DeviceNet connector.

Solid
green

Normal operation The module is operating normally.

Solid red Unrecoverable fault The module detected an

unrecoverable fault.

ArmorBlock Guard I/O DeviceNet Safety Modules 15

Publication

1732DS-IN001D-EN-P - September 2009

Flashing
green

Module needs commissioning due to
missing, incomplete, or incorrect
configuration

Module is unconfigured.

Flashing
red

Recoverable fault or user-initiated
firmware update in progress

The module has detected a
recoverable fault or user-initiated
firmware update is in progress.

Flashing
red and
green

Device in self test The module is performing its

power-cycle diagnostic tests.

(1)

For recommended action, refer to the user manual that covers these modules.

Network Status Indicator

(1)

State Status Description

Off Module not online or no

power

The module is not online with the network.

Flashing
green

Module online with no
connections in
established state

The module identified the communication rate of
the network but no connections are established.

Solid
green

Module online with
connections in
established state

The module is operating normally.

Module Status Indicator

(1)

State Status Description

16 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Flashing
red

One or more I/O
connections in
timed-out state or
user-initiated firmware
update in progress

The module detected a recoverable network fault
or user-initiated firmware update is in progress.

Solid red Critical link failure The module detected an error that prevents it from

communicating on the network.

Flashing
red and
green

Communication faulted
module

The module detected a network access error and is
in communication faulted state. The module
received and accepted an Identity Communication
Faulted Request-long protocol message.

(1)

For recommended action, refer to the user manual that covers these modules.

Safety Input Status Indicator

State Status Description Recommended Action

Off Safety input

off or module
being
configured

The safety input is off or the
module is being configured.

Turn the safety input on or
wait for the module to be
configured.

Solid
yellow

Safety input
on

The safety input is on. None.

Solid red Fault detected A fault in the external wiring

or input circuit detected.

Check configuration, field
wiring, and devices. If no
problem found, replace
module.

Flashing
red

Partner fault
detected

A fault in the partner input
circuit of a dual input
configuration detected.

Check the field wiring and
verify your configuration for
the partner circuit. If no
problem found, replace
module.

Network Status Indicator

(1)

State Status Description

ArmorBlock Guard I/O DeviceNet Safety Modules 17

Publication

1732DS-IN001D-EN-P - September 2009

Safety Output Status Indicator (1732DS-IB8XOBV4 module only)

State Status Description Recommended Action

Off Safety output

off or module
being
configured

The safety output is off
or the module is being
configured.

Turn the safety output on or wait
for the module to be configured.

Solid
yellow

Safety output onThe safety output is on. None.

Solid red Fault detected A fault in the output

circuit was detected.

Check the circuit wiring and end
device. If no problem found,
replace module.

Both tags in a dual
channel circuit do not
have the same value.

Make sure logic is driving tag
values to the same state (off or
on).

Flashing
red

Partner fault
detected

A fault in the partner of
a dual output circuit
was detected.

Check the circuit wiring and end
device of the partner. If no
problem found, replace module.

Configuration Lock Indicator

(1)

State Status Description Recommended

Action

Off No configuration Invalid configuration data. None.
Solid

yellow

Locked Valid configuration, locked

by a network configuration
tool, such as RSNetWorx
for DeviceNet software.

None.

Flashing
yellow

Not locked Valid configuration, owned

by a network configuration
tool, such as RSNetWorx
for DeviceNet software.

None.

(1)

Not applicable if owned by a GuardLogix controller.

18 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Specifications

Technical Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8
Safety Input

Input type Current sinking
Voltage, on-state input, min 11V DC
Current, on-state input, min 3.3 mA
Voltage, off-state input, max 5V DC
Current, off-state, max 1.3 mA
IEC 61131-2 (input type) Type 3

Pulse Test Output

Output type Current sourcing
Pulse test output current 0.7 A
Residual voltage, max 1.2V
Output leakage current, max 0.1 mA
Short circuit protection Yes
Current, max 25 mA - Current, max (to avoid fault when used as a muted

lamp output)

Current, min 5 mA - Current, min (at which fault indication is generated

when used as a muted lamp output)

Safety Output (1732DS-IB8XOBV4 module only)

Output types Current sourcing/current sinking - bipolar pair
Output current rating 2 A max per point

8 A total module @ 40 °C (104 °F)

6 A total module @ 60 °C (140 °F)
On-state voltage drop ±0.6V
Leakage current

±1.0 mA

(1)

ArmorBlock Guard I/O DeviceNet Safety Modules 19

Publication

1732DS-IN001D-EN-P - September 2009

Internal resistance from
PtoM terminal

3.25 kΩ

Short circuit detection Yes (short high and low and cross-circuit fault detect)
Short circuit protection Electronic
Aggregate current of

outputs per module

8 A @ 40 °C (104°F)

6 A @ 60 °C (140 °F)

Pilot duty rating DC-14 Pilot Duty (1732DS-IB8XOBV4 module only)
Number of outputs 4 dual channel

(1)

Includes the presence of a single P stuck-high or M stuck-low short.

General Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8

Enclosure type rating Meets IP64/65/66/67/69K (when product is marked)
Communication power

supply voltage

11…25V DC (supplied from communication power supply)

Communication current
consumption

85 mA at 24V DC

Operating voltage range 19.2…28.8V DC (24V DC, -20…20%)
Isolation voltage 50V (continuous), reinforced insulation type, I/O to

DeviceNet network, I/O to power, and power to DeviceNet

network, Tested at 750V DC for 60s

Technical Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8

20 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Product temperature versus
current derating

Wiring category

(1)

1 - on signal ports

1 - on power ports

2 - on communication ports
Weight, approx. 640 g (1.41 lb)
Dimensions (HxWxD),

approx.

69 x 179 x 70 mm (2.7 x 7.0 x 2.8 in.)

(1)

Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring
and Grounding Guidelines, publication 1770-4.1

.

General Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8

8 A

7 A

6 A

-20 °C 40 °C 50 °C 60 °C

Product Temperature Versus Current Derating
(combined current from both input and output supplies)

44199

ArmorBlock Guard I/O DeviceNet Safety Modules 21

Publication

1732DS-IN001D-EN-P - September 2009

Environmental Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8

Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal
Shock)

-20…60 °C (-4…140 °F)

Temperature, storage
IEC 60068-2-1 (Test Ab, Unpackaged
Nonoperating Cold)
IEC 60068-2-2 (Test Bb, Unpackaged
Nonoperating Dry Heat)

-45…85 °C (-49…185 °F)

Relative humidity
IEC 60068-2-30 (Test Db, Unpackaged Damp
Heat)

5…95% noncondensing

Vibration
IEC 60068-2-6 (Test Fc, Operating)

5 g @ 10…500 Hz

Shock, operating
IEC 60068-2-27 (Test Ea, Unpackaged Shock)

30 g

Shock, nonoperating
IEC 60068-2-27 (Test Ea, Unpackaged Shock)

50 g

Emissions
CISPR 11

Group 1, Class A

ESD immunity
IEC 61000-4.2

6 kV contact discharge
8 kV air discharge

Radiated RF immunity
IEC 61000-4-3

10V/m with 1 kHz sine-wave 80%AM from
80…2000 MHz
10V/m with 200 Hz 50% Pulse 100%AM at
900 MHz
10V/m with 200 Hz 50% Pulse 100%AM at
1890 MHz
3V/m with 1 kHz sine-wave 80%AM from
2000…2700 MHz

22 ArmorBlock Guard I/O DeviceNet Safety Modules

Publication

1732DS-IN001D-EN-P - September 2009

Conducted RF immunity
IEC 61000-4-6

10V rms with 1 kHz sine-wave 80%AM from
150 kHz…80 MHz

EFT/B immunity
IEC 61000-4-4

±4 kV at 5 kHz on power ports
±3 kV at 5 kHz on signal ports
±2 kV at 5 kHz on communication ports

Surge transient immunity
IEC 61000-4-5

±1 kV line-line (DM) and ±2 kV line-earth
(CM) on power ports
±1 kV line-line (DM) and ±2 kV line-earth
(CM) on signal ports
±2 kV line-earth (CM) on communication
ports

Reaction Time

Input reaction time, max 16.2 ms + set values of ON/OFF delays
Output reaction time, max 6.2 ms + (20 ms) relay response time

(1732DS-IB8XOBV4 module)

Signal Sequence

Environmental Specifications - 1732DS-IB8XOBV4, 1732DS-IB8

Attribute 1732DS-IB8XOBV4, 1732DS-IB8

Typ. 600 ms

44072

While safety outputs are in an on state, the signal sequence shown in the figure is
output continuously for fault diagnosis when output pulse testing is enabled.
Confirm response time of device connected to safety outputs so the device does not
malfunction due to off pulse.

Typ. 700 μs

ArmorBlock Guard I/O DeviceNet Safety Modules 23

Publication

1732DS-IN001D-EN-P - September 2009

Additional Resources

For safe and correct use of the product, read these publications:

• DeviceNet Modules in Logix5000 Control Systems User Manual,
publication DNET-UM004

• Guard I/O DeviceNet Safety Modules User Manual, publication

1791DS-UM001

You can view or download publications at

http://literature.rockwellautomation.com. To order paper copies of technical

documentation, contact your local Rockwell Automation distributor or sales
representative.

Certifications - 1732DS-IB8XOBV4, 1732DS-IB8

Certification (when
product is marked)

(1)

1732DS-IB8XOBV4, 1732DS-IB8

c-UL-us UL Listed Industrial Control Equipment, certified for US and

Canada. See UL File E65584.

CE European Union 2004/108/EC EMC Directive, compliant with:

EN 61326-1; Meas./Control/Lab., Industrial Requirements.
EN 61000-6-2; Industrial Immunity.
EN 61000-6-4; Industrial Emissions.
EN 61131-2; Programmable Controllers
(Clause 8, Zone A & B).

C-Tick Australian Radiocommunications Act, compliant with:

AS/NZS CISPR 11; Industrial Emissions.
ODVA ODVA conformance tested to DeviceNet specifications.
TÜV TÜV Certified for Functional Safety up to and including

Category 4 and SIL 3.

(2)

(1)

See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates,
and other certification details.

(2)

When used with specified firmware revisions.

Rockwell Automation Support

Rockwell Automation provides technical information on the Web to assist you in using
its products. At http://www.rockwellautomation.com/support/

, you can find technical
manuals, a knowledge base of FAQs, technical and application notes, sample code and
links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools.

For an additional level of technical phone support for installation, configuration, and
troubleshooting, we offer TechConnect support programs. For more information,
contact your local distributor or Rockwell Automation representative, or visit

http://www.rockwellautomation.com/support/

.

Installation Assistance

If you experience a problem within the first 24 hours of installation, please review the
information that's contained in this manual. You can also contact a special Customer
Support number for initial help in getting your product up and running.

New Product Satisfaction Return

Rockwell Automation tests all of its products to ensure that they are fully operational
when shipped from the manufacturing facility. However, if your product is not
functioning and needs to be returned, follow these procedures.

Allen-Bradley, ArmorBlock Guard I/O, GuardLogix, GuardMaster, Logix5000, Rockwell Automation, TechConnect,
Rockwell Software, and RSNetWorx for DeviceNet are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

United States 1.440.646.3434

Monday – Friday, 8 a.m. – 5 p.m. EST

Outside United States Please contact your local Rockwell Automation representative for any

technical support issues.

United States Contact your distributor. You must provide a Customer Support case number

(call the phone number above to obtain one) to your distributor to complete
the return process.

Outside United States Please contact your local Rockwell Automation representative for the return

procedure.

Publication 1732DS-IN001D-EN-P - September 2009 PN-46668

Supersedes Publication 1732DS-IN001C-EN-P - April 2009 Copyright © 2009 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.