Rocktron 100LTD User Manual
User's Manual
100 Watt Power Amp
50 Watts x 50 Watts
Single Rack Space
1
Introduction
Congratulations on your purchase of the Rocktron Velocity 100LTD power amplier!
The Velocity 100LTD was designed to provide great exibility and high reliability. This
single-rackspace amplier provides 55 watts of power per channel into a 4 ohm load, or 40
watts per channel into an 8 ohm load.
In addition, the Velocity 100LTD incorporates thermal protection circuitry, as well as
output short circuit protection.
This manual will introduce you to the Velocity 100LTD and its features, please keep it for
future reference.
Your Rocktron Velocity 100LTD power amplier has been tested and complies with the following
Standards and Directives as set forth by the European Union and CSA:
Standard(s): IEC60065 Professional Audio/Video or Similar
Equipment, EN55013:1997, EN6100LTD0-3-2 (1995)
EN6100LTD0-3-3(1995), EN55020:1995, CSA E65-94
This means that this product has been designed to meet stringent guidelines on how much RF energy
it can emit, and that it should be immune from other sources of interference when properly used. Improper use of this equipment could result in increased RF emissions, which may or may not interfere
with other electronic products.
To insure against this possibility, always use good shielded cables for all audio input connections.
This will help insure compliance with the Directive(s).
Copyright © 2014 GHS Corporation
All Rights Reserved.
2
Precautions - Please read!!
NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE YEARS OF
TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HANDLING.
1. Read all instructions contained in this manual
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including ampliers) that produce heat.
9. This product may be equipped with either a polarized alternating-current line plug (which is a
plug that has one blade wider than the other) or a plug with two blades with a third grounding
prong. The wide blade or the third prong are provided as a safety feature. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched - particularly at the plugs,
convenience receptacles, and that the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Do not use this product with any case, stand, tripod, bracket or table that is not specied by
the manufacturer. Where it is specied by the manufacturer insure that the case, stand,
tripod, bracket, etc. is properly adjusted and setup. Extra care and caution should be taken to
avoid tip over and injury.
13. Unplug this apparatus during lightning storms or when unused during long period of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus or if the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT SHOULD BE
SERVICED BY QUALIFIED PERSONNEL ONLY. DO NOT MAKE ANY INTERNAL
ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY TIME OR TAMPER WITH
INTERNAL ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY VOID THE WARRANTY OF THIS EQUIPMENT, AS WELL AS
CAUSING SHOCK HAZARD.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to operate between 32° F and 104° F
(0° C and 40° C). This unit may not function properly under extreme temperatures.
3
Front Panel
1
2
3
LEVEL Control (Channel 1/Ch.1): When used in stereo (two inputs into Ch.1 and
Ch.2 on the back of the unit) this control determines the volume level for Channel 1
output only. When used in MONO (one input into Ch.1 input on the back of the unit)
this control determines the volume level of both Ch.1 and Ch.2 outputs.
RESONANCE Control (Channel 1/Ch.1): This control "beefs up" the lower range
giving the Velocity 100LTD extra performance at the low-end of the sonic spectrum.
When used in stereo (two inputs into Ch.1 and Ch.2 on the back of the unit) this
control determines the amount of RESONANCE for Channel 1 only. When used in
MONO (one input into Ch.1 input on the back of the unit) this control determines the
RESONANCE of both Ch.1 and Ch.2 outputs.
PRESENCE Control (Channel 1/Ch.1): This control opens up the treble and higher
end, offering more "voice" for solo playing. When used in stereo (two inputs into Ch.1
and Ch.2 on the back of the unit) this control determines the amount of PRESENCE
for Channel 1 only. When used in MONO (one input into Ch.1 input on the back of
the unit) this control determines the PRESENCE of both Ch.1 and Ch.2 outputs.
4
5
6
7
4
8
LEVEL Control (Channel 2/Ch.2): This control determines the volume level for
Channel 2.
RESONANCE Control (Channel 2/Ch.2): This control determines the amount of
RESONANCE for Channel 2. This control "beefs up" the lower range giving the
Velocity 100LTD extra performance at the low-end of the sonic spectrum.
PRESENCE Control (Channel 2/Ch.2): This control determines the PRESENCE
for Channel 2. This control opens up the treble and higher end, offering more "voice"
for solo playing.
POWER LED: This is the "POWER" LED. When the Velocity 100LTD is "ON" the
LED will be lit or "ON".
POWER SWITCH: This switch powers up the Velocity 100LTD.
Loading...