Rock-Slide Engineering RIGID SERIES FRONT BUMPER User Manual

RIGID SERIES FRONT BUMPER

FB-F-100-JK, FB-F-101-JK, FB-F-102-JK, FB-F-103-JK

FB-S-100-JK, FB-S-101-JK, FB-S-102-JK, FB-S-103-JK

(JKA part number denotes Aluminum products)

Vacuum Canister Relocation Bracket required for years 2010-

2014. Relocation Brackets can be purchased through R-SE

(part # AC-CRL-100)

INSTALLATION INSTRUCTION RSEI 100

PARTS LIST

QTY

DESCRIPTION

1

Front Bumper

2

Light Bracket (L-Brackets)

2

5/16''x1'' Bolts

2

5/16'' Locking Nuts

2

4.5''x7/16'' Bolts

4

5/16'' Washers

8

7/16''x1'' Bolts

10

7/16'' Nuts

18

7/16'' Washers

*Optional: Bull Bar

*If you have purchased a bumper without a bull bar (FB-F-101-JK, FB-F-102­JK, FB-S-101-JK, FB-S-102-JK) you will only need 4 7/16’’x1’’ bolts and 4
7/16’’ washers.

*If you have purchased a shorty front bumper (FB-S-100-JK, FB-S-101-JK, FB­S-102- JK, FB-S-103-JK) you will not have the light brackets (L-brackets),
5/16’’x1’’ bolts or 5/16” locking nuts.

*If any parts listed are missing or damaged please call Rock-Slide Engineering @

435-752-4580 prior to installation

INSTALLATION INSTRUCTION RSEI 100

RIGID SERIES FRONT BUMPER INSTALLATION

**WARNING: MUST READ**

DO NOT REMOVE FRONT BUMPER UNTIL YOU HAVE DISCONNECTED THE LIGHT WIRE
HARNESS AND LIGHTS. FAILURE TO DO SO CAN RUIN YOUR TRACTION CONTROL SYSTEM.

1. After you have disconnected the light wire harness and lights, remove the

stock plastic bumper and skid plate.

Installing with winch

1. Mount the winch on the bumper before mounting the bumper onto the Jeep.
a. Use the hardware provided with the winch to secure it to the bumper

2. If optional Bull Bar is included, mount Bull Bar to bumper prior to installing.
a. Mount the R-SE Rigid Series Bull Bar using the following:

4 7/16’’x1’’ bolts, 4 7/16’’ washers

3. Secure the R-SE Rigid Series bumper using the following.
a. 8 7/16’’x1’’ bolts, 8 7/16’’ nuts, 16 7/16’’ washers
b. You will be using 2 washers per bolt and nut

4. Secure the winch plate by placing the following through the frame into the

winch plate.

Failure to secure the winch plate to the frame with the bolts provided will
cause winch plate to twist and cause your winch to malfunction.

a. 2 4.5’’x7/16’’ bolts, 2 7/16’’ nuts, 4 7/16’’ washers

*Aluminum products will use a 3/8” bolt and washer to mount Bull Bar to bumper.
Included in the hardware kit.

INSTALLATION INSTRUCTION RSEI 100

LIGHTS

For wiring you can use the stock light harness and use the stock light switch or you
can follow the directions that came with the lights to hook up to the battery directly
and use the switch they provide. To mount the light, use the following.

a. 2 Light brackets (L-Brackets), 2 5/16’’x1’’ bolts, 2 5/16’’ locking nuts

Lights R-SE has used: PIAA 520 / HELLA 500FF

Thank you for choosing Rock-Slide Engineering products. We value your business
and welcome your feedback/suggestions. If you have any concerns please contact

us directly @ 435-752-4580. We are here to help you!

INSTALLATION INSTRUCTION RSEI 100