Rockhood TouchWin TH465-M, TouchWin TH765-M, TouchWin TH865-M, TouchWin THA61-M User Manual
TH series Touch Screen
User’s manual
Rockhood Automation Co.,Ltd
Preface
Thank you for buying TH series touch screen made by Rockhood Automation Co., Ltd, this
manual should be read and understood before doing relative operation.
Purpose
This manual will guide readers in the correct operating and maintaining TH series touch
screen. Also, this manual refers to the application situations, operations, transportation,
storage, set up, installation, maintaining and so on.
This manual mainly contains three parts: hardware, software, application.
¾ Hardware Part: contain the characteristics, specifications, dimensions, installations and
communication connecting of TH series.
¾ Software Part: introduce how to use the edit software.
¾ Application Part: illustrate the examples, make users to know TH better.
下面的内容只针对 TP 系列产品。
Please read this manual very carefully before operation and please do the correct operations
while paying close attention to all the safty points.The following contents only used for TP
series touch screen.
Personnel
This manual is fit for following personnel:
¾ End Users
¾ Engineers
¾ Technicians
Please read the safety notes carefully before using the products.
Contact us
If you have any questions, please contact us use the following methods:
Email:
rockhood@gmail.com
Tel: 86 21-65322066 0086-13661780977
Fax: 86 21-56322611
Address: 4
th
Floor, Building 7, Original Industrial Park, No.100 Dicui Road,
Wuxi, Jiangsu province, China
Safety caution
Please read the manual carefully before using. Make sure your operation is correct and safety. The
following contents are only aimed at TH series products.
Please keep the manual properly, put in the location easy to get and read, hand the manual to the
end users.
NOTICE
z Please do not bundle power line with communication cable or let them too close,
keep at least 10cm.
z Please do not install module or change the wire. Otherwise it may cause
malfunction, error action, damage or fire.
z Please shut off the power when there is abnormal smell or voice in TH products.
(The short sound made by buzzer after power on is normal)
z Do not strike the touch panel with a hard or sharp object, or press on the touch
panel with too much force or with pen, screw, since it may damage the touch panel
and cause damage.
z Please tighten the screws when install the products to prevent from falling off.
z Please transport, store, set up, install and maintain the products correctly, otherwise
the touch panel may be damaged.
DANGERS
z Confirm the rated voltage of TH and connect correct before power on.
z Please do not touch the terminals after power on to avoid electric shock.
z Please do not open the cover board.
z Please cut off all the power when installing or disassembling the products, or it
may cause error action and malfunction.
z Please use TH touch screen in suitable environment conditions according to
instructions, otherwise it may cause accident.
z Please do not use the products where there is high frequency radiate, high magnetic
field or other interferences.
Catalog
Preface ..............................................................................................................................................3
Safety caution....................................................................................................................................4
1. Summarize ................................................................................................................................6
1.1 Performance characteristics ..........................................................................................6
1.2 Work flow............................................................................................................................7
2. General specification.....................................................................................................................8
2.1 TH465-M ............................................................................................................................9
2.2 TH765-M ..........................................................................................................................10
2.3 TH865-M ..........................................................................................................................11
2.4 THA61-M..........................................................................................................................12
3. Hardware..................................................................................................................................... 13
3.1 Hardware structure............................................................................................................13
3.2 Dimension .........................................................................................................................14
3.3 Installation and using environment ...................................................................................16
4. Interface and switch ......................................................................................................................1
4.1 Introduction.........................................................................................................................1
4.2 DIP switch...........................................................................................................................1
4.3 COM1 port ..........................................................................................................................1
4.4 COM2 port ..........................................................................................................................4
4.5 USB-A port .........................................................................................................................5
4.6 USB-B port .........................................................................................................................6
5. TouchWin software ....................................................................................................................... 8
5.1 Preparation ..........................................................................................................................8
5.2 The construction of Touchwin.............................................................................................9
5.2.1 Screen.......................................................................................................................9
7. Application..................................................................................................................................10
7.1 Adjust the touch area.........................................................................................................10
7.2 Photo application...............................................................................................................11
7.3 Debug and download ........................................................................................................15
7.4 Data duplication ................................................................................................................16
8. TH series touch screen interior objects .......................................................................................17
1. Summarize
Rockhood new touch screen TH series are based on RT/TP series products. It not only has the
language, characters editing, data display, monitor and alarm functions but also has 65536 true
color LCD which can bring you brand-new vision enjoyment. It has the advantage of large
capability for data duplication and friendly user interface. It provides perfect humanized solution
for industrial system, make it easy to control the system.
The function compare between TP and TH:
Function compare
Series
Colors
Font
setting
3D
picture
library
Adjust
the touch
area
Animation Password
Two ports
USB data USB data
communication
download duplication
indenpendently
√ 〇 〇 √ √ √ 〇 〇
256
RT/TP
65536
√ √ √ √ √ √ √ √
TH
1.1 Performance characteristics
Display
z Various models: product size from 4.7’’ to 10.4’’.
z Rich colors: 65536 TFT true color, support BMP, JPG format, display more lively.
z Adjust function for touch screen.
z Support multinational language: simple/traditional Chinese, English, Japanese, Korean.
Define the font as you like, support underline, italic, bold, shadow and other art words.
z Large picture library, with preloading mode, no delay for screen motion.
Control
z Switch control, dynamic monitor and display data, bar map, real time trend map, time trend
map, XY trend map, discrete/continue column map, real time alarm, history alarm record…
z User-defined data collection and saving function
z Set user’s authority, 9 levels password protection
z Simulate online/offline, upload/download data, configuration function
z USB port inside, connect flash disk to realize data duplication function, speed 480Mbps
z Special USB-B port for data download, make the data transfer faster
z User-defined animation track design
Communication
z Two ports communication independently, can connect two different devices at the same time
z Drive the panel printer directly, economical and flexible
z Support free format communication, user edits the driver program
1.2 W ork flow
The work flow of using TH:
Install edit software TouchWin
Edit your project
Connect PC and TH, power on
Do simulate offline Do simulate online
Simulate the TH
action in the
software.
Connect the PC with
TH, simulate the action
in your PC
Download project in TH
Connect TH with other devices
Realize communication and data transmission
NOTICE
Please use TouchWin V2.C and later version to edit your TH project.
2. General specification
This chapter will introduce the specification of TH series touch screen.
TH series touch screen contains TH465-M, TH765-M, TH856-M and THA61-M.
Series Types
TH
TH465-M TH765-M TH865-M THA61-M
2.1 TH465-M
Item TH465-M
DC20-DC28V Input voltage
Consumption current 130mA
Less than 10ms Momentary power off
allowance
Withstand voltage AC1000V-10mA 1 minute ( signal and time )
Electrical
DC500V- about 10MΩ ( signal and time ) Insulated impedance
COM1 Support RS-232/RS-485
COM2 Support RS-232/RS422/RS485
USB1 USB-A ( accord with USB2.0 )
USB2 USB-A ( accord with USB2.0 )
Interface
USB3 USB-B ( accord with USB2.0 )
0－50℃ Operation temperature
-20-60℃ Reserve temperature
20-85% ( no condensation ) Environment
temperature
Withstand oscillation 10-25Hz ( X, Y, Z each direction 30 minutes 2G )
Anti-jamming Voltage noise: 1000Vp-p, pulse 1us, 1 minute
Surrounding air No corrosive gas
Environment
Protection construction IP65
Type 65536 true colors
Screen size 4.3 inch
More than 50000 hours, 24 hours running when surrounding
temperature is 25 ℃
Use life
Resolution 480*272
Contrast Non-adjustable
Character Chinese, English, Korean, Japanese…
Character size Any size and font
Screen
specification
4-wire resistance mode Touch panel
Memory
Screen 8MB
Cooling method Natural air cooling
Exterior dimension 150.0*100.0*41.0mm
Construction
144.0*94.0mm Mounting dimension
2.2 TH765-M
TH765-M
Item
DC20-DC28V Input voltage
Consumption current 250mA
Less than 10ms Momentary power off
allowance
Withstand voltage AC1000V-10mA 1 minute ( signal and time )
Electrical
DC500V- about 10MΩ ( signal and time ) Insulated impedance
COM1 Support RS-232/RS-485
COM2 Support RS-232/RS422/RS485
USB1 USB-A ( accord with USB2.0 )
USB2 USB-A ( accord with USB2.0 )
Interface
USB3 USB-B ( accord with USB2.0 )
0－50℃ Operation temperature
-20-60℃ Reserve temperature
20-85% ( no condensation ) Environment
temperature
Withstand oscillation 10-25Hz ( X, Y, Z each direction 30 minutes 2G )
Anti-jamming Voltage noise: 1000Vp-p, pulse 1us, 1 minute
Surrounding air No corrosive gas
Environment
Protection construction IP65
Type 65536 true colors
Screen size 7 inch
More than 50000 hours, 24 hours running when surrounding
temperature is 25 ℃
Use life
Resolution 800*448
Contrast Non-adjustable
Character Chinese, English, Korean, Japanese…
Character size Any size and font
Screen
specification
4-wire resistance mode Touch panel
Memory
Screen 64MB
Cooling method Natural air cooling
Exterior dimension 205.0*151.5*48.9mm
Construction
192.0*138.5mm Mounting dimension
2.3 TH865-M
TH865-M
Item
DC20-DC28V Input voltage
Consumption current 260mA
Less than 10ms Momentary power off
allowance
Withstand voltage AC1000V-10mA 1 minute ( signal and time )
Electrical
DC500V- about 10MΩ ( signal and time ) Insulated impedance
COM1 Support RS-232/RS-485
COM2 Support RS-232/RS422/RS485
USB1 USB-A ( accord with USB2.0 )
USB2 USB-A ( accord with USB2.0 )
Interface
USB3 USB-B ( accord with USB2.0 )
0－50℃ Operation temperature
-20-60℃ Reserve temperature
20-85% ( no condensation ) Environment
temperature
Withstand oscillation 10-25Hz ( X, Y, Z each direction 30 minutes 2G )
Anti-jamming Voltage noise: 1000Vp-p, pulse 1us, 1 minute
Surrounding air No corrosive gas
Environment
Protection construction IP65
Type 65536 true colors
Screen size 8 inch
More than 50000 hours, 24 hours running when surrounding
temperature is 25 ℃
Use life
Resolution 800*600
Contrast Non-adjustable
Character Chinese, English, Korean, Japanese…
Character size Any size and font
Screen
specification
4-wire resistance mode Touch panel
Memory
Screen 64MB
Cooling method Natural air cooling
Exterior dimension 224.4*170.8*45.5mm
Construction
211.4*157.8mm Mounting dimension
2.4 THA61-M
THA61-M
Item
DC20-DC28V Input voltage
Consumption current 630mA
Less than 10ms Momentary power off
allowance
Withstand voltage AC1000V-10mA 1 minute ( signal and time )
Electrical
DC500V- about 10MΩ ( signal and time ) Insulated impedance
COM1 Support RS-232/RS-485
COM2 Support RS-232/RS422/RS485
USB1 USB-A ( accord with USB2.0 )
USB2 USB-A ( accord with USB2.0 )
Interface
USB3 USB-B ( accord with USB2.0 )
0－50℃ Operation temperature
-20-60℃ Reserve temperature
20-85% ( no condensation ) Environment
temperature
Withstand oscillation 10-25Hz ( X, Y, Z each direction 30 minutes 2G )
Anti-jamming Voltage noise: 1000Vp-p, pulse 1us, 1 minute
Surrounding air No corrosive gas
Environment
Protection construction IP65
Type 65536 true colors
Screen size 10.4 inch
More than 50000 hours, 24 hours running when surrounding
temperature is 25 ℃
Use life
Resolution 640*480
Contrast Non-adjustable
Character Chinese, English, Korean, Japanese…
Character size Any size and font
Screen
specification
4-wire resistance mode Touch panel
Memory
Screen 64MB
Cooling method Natural air cooling
Exterior dimension 311.0*234.0*48.0mm
Construction
302.0*225.0mm Mounting dimension
3. Hardware
3.1 Hardware structure
The hardware structure of TH series touch screen includes front and back side. Take TH465-M as
an example to explain the structure.
USB-A port
Touch area
Power LED
USB-A port
Label
USB-B port
Power Plug COM1 port COM2 port DIP switch
3.2 Dimension
r dimension:150.0mm×100.0mm×41.0mm, mounting dimension:
144.0mm×94.0mm.
) TH765-M exterior dimension:205.0mm×151.5mm×48.9mm, mounting dimension:
192.0mm×138.5mm.
(1) TH465-M exterio
(2
144.0
94.0
24V 0V FG
1234
92.0
142.0
41.0
150.0
100.0
COM1 COM2
138.5
192.0
48.9
12.0
136.5
190.0
1234
24V 0V FG
1234
COM1 COM2
205.0
151.5
(3) TH865-M exterior dimension: 224.4mm×170.8mm×45.5mm, mounting dimension:
211.4mm×157.8mm.
(4) THA61-M exterior dimension: 311.0mm×234.0mm×48.0mm, mounting dimension:
02.0mm×225.0mm.
3
211.4
157.8
1234
1234
Download
PLC
24V0V FG
224.4
170.8
38.0
45.5
155.8
209.4
302.0
225.0
+24V 0V FG
311.0
234.0
48.0
223.0
43.1
300.0
1234
+24V 0V FG
COM1 COM2
3.3 Installation and using environment
(1) Install requirements:
TH has four ferric mounting racks when out of factory, there are two square holes on the up, down
side of TH, use mounting rack to fix the TH with control cabinet.
In order to avoid TH temperature too high after long time working, please keep 10cm space on the
up/down and 5cm on the left/right side of the TH when installing.
(2) Install steps
rectangle mounting hole in the
Install panel
Fixed bracket
Step1 Refer to the dimension in the former chapter to open a
control cabinet
Step2 Add airproof circles in the airproof slot when installing
Step3 Insert the bottom of TH into the mounting hole of control cabinet
Step4 Insert the install rack into the fix hole of TH then tighten the screw
Step5 Connect TH and PLC with communication cable
NOTICE
The communication cable can be offered by the supplier or made by user according to the
connection map, input +24V DC power to start working
(3) Environment
TH series touch screen indoor.
, steam, dust, fast vary temperature, high humidity ( it may cause moisture inside
TH).
Please use
Do not use TH in below environment:
Inflammable gas
(4) Power supply requirements:
TH series touch screen use DC +24V power supply only. The permitted voltage range is 20V~28V.
Besi
elec
C +24V output of PLC to drive the TH, make sure the PLC has enough current
the back cover by yourself.
Please do not analyze or change TH by yourself
Please cut off all the power supply while observing the TH.
Please do not touch terminals after power on, otherwise it may cause electric shock.
Do not hot plug the cable or pull the cable when communicating, it may destroy the cable.
Please periodic check installation and screws to avoid falling off.
h area, in order to keep touch sensitivity.
Please use clean cloths with little detergent or alcohol to clean the screen.
d out acid, alkali is recommended.
Keep the thrill or strong corrosive gas
Never use spray detergent.
he screen too hard while wiping.
The connection is as below:
+24V
0 V
+DC-
des, if connect high voltage or AC power supply with TH, the TH may be damaged and cause
tric shock to human body.
NOTE: if use the D
to drive the TH.
(5) Maintenance and cleaning
z Please do not open
z
z
z
z
z
z Please use TH series touch screen in the certain conditions according to instructions.
z Keep the cleanness of touc
z
z Neutral etergent, with
TH away from
z
z
z Avoid damage to the screen, please do not touch t
Caution
Maintenance
Clean
Caution
Disposal
Caution
z Please dispose the TH as industry waste.
4. Interface and switch
4.1 Introduction
TH series touch screen has 1 group of DIP switch and 5 communication ports.
1 2 3 4
5
6
1: DIP switch 4: USB-A port1
2: COM1 port 5: USB-A port2
3:COM2 port 6: USB-B port3
4.2 DIP switch
TH has one group of DIP switch at the back side, they can set the function of COM1 port.
Switch Switch1 Switch2 Switch3 Switch4 Function
ON OFF OFF OFF Undefined
OFF ON OFF OFF Forced download mode of COM1
OFF OFF ON OFF Adjust mode of touch area
State
OFF OFF OFF ON Interior check mode ( not recommend to use)
4.3 COM1 port
TH series touch screen COM1 port has these functions:
¾ Communication function: connect with PLC, printer, frequency inverter, used as communication port.
¾ Download function: connect with PC, used to download data and screens.
COM1 port pins definition
Pin Name Meaning
12345
6789
1 NC Unused terminal
2 RXD RS232 receive
3 TXD RS232 send
4 A RS485 + signal
5 GND Signal ground
6 NC Unused terminal
7 B RS485 – signal
8 NC Unused terminal
9 NC Unused terminal
z Download function
The following terms should be met when using download function:
(1) Turn on switch 2 in DIP switch group to make the COM1 in download mode.
(2) Please use the cable provided by Rockhood company
Step:
Make sure your PC has serial port or USB port ( use USB converter tool), connect it with COM1, then click
in the software to download data. The pins definition is shown as below:
PC serial port TH COM1 port
PC
Rockhood download cable
TH
(1) Turn on switch2 when TH power supply is cut off
(2) Power on TH, connect TH with PC via Rockhood download cable to download
project
(3) After the download process is over, cut off the power of TH, then turn off the
switch2
(4) Power on the TH again, the project will run normally
Figure: Download cable connection
z Forced download
1234
ON
OFF
About the TH download
details, please refer to the chapter “build a simple project---project download”.
z Communication function
COM1 port has strong communication functions. The default mode of COM1 is communication mode.
COM1 default mode is communication mode, you can realize the communication function by setting the
Response dat
a
Send data
Frequency inverter
PLC
TH
After the download is completed, if the TH can not display the screen normally, you
can try forced download mode to update the system.
Step:
(1) Cut the power of TH, turn on switch2
(2) Power on the TH, connect the cable then download the
project
(3) After the download is completed, turn off switch2 then
power on the TH again.
COM1 port Other devices
correct communication parameters and device
COM1 port communication parameter COM1 port communication device
4.4 COM2 port
CO 2 port has below functions: M
Communicate with industry devices, such as PLC, inverter, meters…
COM2 port pins definition
¾
12345
6789
z unicate with
Select the correct PLC type in the list and set the communication parameters:
Comm
PLC
TH can communicates with most mainstream PLC.
Data transfer
TH series
COM2
pins Name Meaning
1 TD+ RS422 send +
2 RXD RS232 receive
3 TXD d RS232 sen
4 A RS485 +
5 GND Signal ground
6 TD- nd - RS422 se
7 B RS485 8 RDD- RS422 receive 9 RDD+ RS422 receive +
SIEMENS
PLC
Panasonic PLC
Omron PLC…
Please refer to “TP connect with PLC” for the details of TH communicate with PLC.
z Communicate with frequency inverter
TH can communicate with various brands of frequency inverters. For the brands which are not in the
list, user can select Modbus protocol or user-defined protocol.
COM2
TH
Mitsubishi FR series inverter
Inovance MD series inverter
Bosch Rexroth Indracontrol
L40
Please refer to “TP series touch screen application examples” for the details of TH
communicating with frequency inverter.
z Communicate with meters
About the communication between TH and meters, users can select user-defined protocol or Modbus
protocol.
Please refer to “TP series touch screen application examples” for the details of TH
communicating with meters.
4.5 USB-A port
TH has two USB-A ports ( accord with USB2.0 ). The functions are show as below:
¾ Duplicate data, data import and export, transmission speed can be 480Mbps.
USB-A port definition
Pins Name Meaning
1 +5V +5V voltage signal
2 DATA+ Data signal +
3 DATA- Data signal 4 -5V -5V voltage signal
z Connect U-disk and other USB port devices
TH front side TH back side
USB-A
USB-
A
p
ort
USB-A
USB cable
TH front side
USB mobile
harddisk
4.6 USB-B port
TH has one USB-B port ( accord with USB2.0 ), located in the back side of TH, the functions are shown as
below:
¾ To download the data, the speed can up to 480Mbps.
USB-B port definition:
Please use the USB cable sold in the market when connecting PC with USB-B port, then click
in
the software to download your project in TH.
Pins Name Meaning
1 +5V +5V voltage signal
2 DATA+ Data signal +
3 DATA- Data signal 4 GND Ground signal
TH back side
PC
USB cable
5. TouchWin software
5.1 Preparation
1. Software version: V2.B and later versions.
2. Software source: visit Rockhood website
www.rockhood.com to obtain the software or get from the
products CD.
3. OS requirements: Windows98/2000/XP/ME
4. Install steps:
Open setup.exe
Click “next” until show below window
Enter the information in the space: serial number is ThingetTouchWin.
Click “next” to finish your installation.
click to use the software.
5.2 The construction of T ouchwin
5.2.1 Screen
Double click the Touchwin software, build a new project, then you can see the following screen:
7. Application
7.1 Adjust the touch area
The touch area adjustment function can make the component touch more precise.
The adjustment steps:
Step 1: turn on the DIP switch 3, then power on the TH again, it will show the following screen:
Step2: After clicking the cross center, the adjust cross will jump to the second position. Click the center of
the cross again.
Step3: Click the cross center again, the cross will jump to the third position.
Adjust cross
● Click the center of the adjust cross
● Turn on switch 3
OFF
ON
2134
Step4: Click the cross center again, it will show two results.
This result means the adjustment is
successful. You can set the DIP switch to
working mode, then restart the TH again.
Then you can use TH as normal.
This result means the adjustment is failed.
You should click the cross center again to
redo the adjust steps.
7.2 Photo application
TH series LCD are 65536 true colors, it can make your photo display more vividly.
This example will make the photo moving in parallel.
Step1: select the photo
Click
button in the tool bar to open the material library:
Select the photo you want, then click “open” button, the photo will be added on the screen.
Step2: design the motion track
Click the
button in the tool bar, drag your mouse to draw the motion track, double click the mouse to
finish the drawing. Please see the drawing:
Step3: combine the photo with the motion track
Drag your mouse to select the photo and the motion track, then right click the mouse, select “group”.
Step4: Simulate offline
to simulate offline your project. You can see the photo motion track.
Click
Step5: Change the animation property
Right click the photo, then select “animal prop”.
The animation property includes coordinate and control.
(1) Coordinate
z X: the position on X axis
z Y: the position on Y axis
z Escape time: the time that the photo moves from (X1,Y1) to (X2,Y2)
z Key point X,Y: the coordinate of every motion position
You can click the X, Y position and the escape time in the list and modify them.
(2) Control
z Enable: control the animation by bit signal. When the rising edge of the signal is coming, the
animation will be activated.
z Reset: control the end of the animation by bit signal. When the rising edge of the signal is coming, the
animation will end.
z Repeat: repeat the motion of the animation.
7.3 Debug and download
TH series touch screen support debug download function. This function can be used when you are
debugging your project in order to save your time.
Compared with normal download function, this function has the following advantages:
(1) This function only can be used when debugging the project.
(2) The data transfer speed is faster than normal download, save time and cost.
button in the tool bar to debug download the project into your TH.
Click
7.4 Data duplication
8. TH series touch screen interior objects
This chapter will introduce the interior objects of the TH.
The interior objects contain PSB(bit register), PSW(word register), PFW(word register).
NOTICE
1. Only when the advanced function is opened, the special interior objects can be used.
2. PSB0~PSB255, PSW0~PSW255, PFW0~PFW255 are occupied by system.
Bit register PSB
Register Function Remark
PSB0 Normally closed coil
PSB1 Normally open coil
PSB2 Turn on during the first scan period
ON
OFF
50ms
50ms
PSB3 100ms pulse signal
ON
OFF
500ms
500ms
PSB4 1s pulse signal
ON
OFF
30s
30s
PSB5 1minute pulse signal
ON
OFF
150ms
150ms
PSB6 300ms pulse signal
PSB15 Communication failure 0: successful 1: failed
PSB16 Succeed to scan the screen once
PSB30 First scan after download
PSB31 First scan after power on
PSB39 Turn off the touch screen
PSB60 Level 1 password flag (1: password is opened, 0: password is closed )
PSB61 Level 2 password flag (1: password is opened, 0: password is closed )
PSB62 Level 3 password flag (1: password is opened, 0: password is closed )
PSB63 Level 4 password flag (1: password is opened, 0: password is closed )
PSB64 Level 5 password flag (1: password is opened, 0: password is closed )
PSB65 Level 6 password flag (1: password is opened, 0: password is closed )
PSB66 Level 7 password flag (1: password is opened, 0: password is closed )
PSB67 Level 8 password flag (1: password is opened, 0: password is closed )
PSB68 Level 9 password flag (1: password is opened, 0: password is closed )
Word register PSW
Register Function Remark
PSW0 Start screen No.
PSW1 Current screen No.
PSW20 Screen width ( read only )
PSW21 Screen height ( read only )
PSW26 PSB amounts ( read only )
PSW27 PSW amounts ( read only )
PSW28 PFW amounts Occupy PSW28、PSW29 ( read only )
PSW30 Year ( Hex) ( read only )
PSW31 Month ( Hex) ( read only )
PSW32 Day ( Hex) ( read only )
PSW33 Hour ( Hex) ( read only )
PSW34 Minute ( Hex) ( read only )
PSW35 Second ( Hex) ( read only )
PSW36 Week ( Hex) ( read only )
PSW40 Recipe index
PSW54 The device quantity
PSW60 COM1 communicate successful time
PSW61 通讯口 COM1 通讯失败次数
PSW62 通讯口 COM1 通讯超时次数
PSW63 通讯口 COM1 通讯数据出错次数
PSW64 通讯口 COM1 设备版本号
PSW65 通讯口 COM1 设备型号
PSW70 通讯口 COM2 通讯成功次数
PSW71 通讯口 COM2 通讯失败次数
PSW72 通讯口 COM2 通讯超时次数
PSW73 通讯口 COM2 通讯数据出错次数
PSW74 通讯口 COM2 设备版本号
PSW75 通讯口 COM2 设备型号
Word register PFW
Register Function Remark
PFW1 The screen No. after power on
PFW2 Background color setting
PFW10 Screen saver start time
PFW11 屏幕保护时显示的画面号
PFW20 通讯口 COM1 波特率 4800、9600、19200、38400、115200、187500
PFW21 通讯口 COM1 数据位 7、8
PFW22 通讯口 COM1 停止位 0-1 bit, 1-1.5 bits, 2-2 bits
PFW23 通讯口 COM1 校验 0-None, 1-Odd, 2-Even
PFW24 通讯口 COM1 站号
PFW25 通讯口 COM2 发送延时 单位：ms
PFW30 通讯口 COM2 波特率 4800、9600、19200、38400、115200、187500
PFW31 通讯口 COM2 数据位 7、8
PFW32 通讯口 COM2 停止位
0-1 bit, 1-1.5 bits, 2-2 bits
PFW33 通讯口 COM2 校验
0-None, 1-Odd, 2-Even
PFW34 通讯口 COM2 站号
PFW35 通讯口 COM2 发送延时 单位：ms
PFW60 一级密码 占用 PFW60、PFW61
PFW62 二级密码 占用 PFW62、PFW63
PFW64 三级密码 占用 PFW64、PFW65
PFW66 四级密码 占用 PFW66、PFW67
PFW68 五级密码 占用 PFW68、PFW69
PFW70 六级密码 占用 PFW70、PFW71
PFW72 七级密码 占用 PFW72、PFW73
PFW74 八级密码 占用 PFW74、PFW75
PFW76 九级密码 占用 PFW76、PFW77
Loading...