Installation et fonctionnement
Instalación y funcionamiento
Einbau und Betrieb
Installazione e funzionamento
Page 2
SAFETY
CAUTION: Before installation, disconnect the battery
negative (-) terminal to prevent damage
to the unit, fire and/or possible injury.
PRACTICE SAFE SOUND™
Continuous exposure to sound pressure levels over 100dB may
cause permanent hearing loss. High powered auto sound systems
may produce sound pressure levels well over 130dB. Use common
sense and practice safe sound.
CARTON CONTENTS
• (1) Set R1 Series Speakers with Tweeters or R1T-S Tweeter Kit
• (1) Set of grilles/trim rings
• Mounting Hardware and Tweeter Surface/Angle and Flush Mounts
INSTALLATION CONSIDERATIONS
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempting to
install these speakers.
2. For safety, disconnect the negative lead from the battery prior to beginning the
installation.
3. For easier assembly, we suggest you run all wires prior to mounting your speakers
in place.
4. Use high quality connectors for a reliable installation and to minimize signal or
power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines,
brake or hydraulic lines, vacuum lines or electrical wiring when working on any
vehicle. If installation in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or
hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic
grommets to protect any wires routed through metal, especially the firewall.
MOUNTING
1. Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly.Be sure that the mounting location is deep enough
for the speaker to fit; if mounting in a door, operate all functions (windows, locks,
etc.) through their entire operating range to ensure there is no obstruction.
2. Refer to the specification chart to determine the proper diameter hole to cut
for your speaker model.The template provided also gives the proper cutout size.
3. Mark the locations for the mounting screws. Drill the holes with a 1/8" bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals.
Be sure to observe proper polarity when connecting the wires.The speaker's
positive terminal is indicated with a "+".
5. Tighten the screws until the speaker is snug in place to prevent rattling. Do not
over tighten the screws.
ar
Re
Deck
Cutout
Hole
Example of Standard Door Installation
Cutout
Hole
Example of
Rear Deck Installation
2
Page 3
FEATURES
SPECIFICATIONS
Built-In Tweeter Crossover
For the R152 S and R1652 S, a HP (High Pass)
crossover is integrated into the tweeter housing.
This crossover allows for easy connection of the
full component system. Just jump wires from the
secondary terminals on the mid range/woofer to
the tweeter terminals, see diagram below.
NOTE:
The tweeter has an integrated 6dB/octave HP
crossover. The mid-range/woofer has natural roll-off
characteristics exhibit great acoustic crossover filtering.
PRIME Components
R152-SR1652-SR1T-S
Nominal Diameter - inch (mm)5.25 (133)6.5 (165)1.0 (25)
Grille/Trim Ring Diameter-inch (mm)6.10 (154.6)7.01 (178)2.13 (54)
Grille/Trim Ring Height-inch (mm)0.70 (17)0.67 (17) 0.29 (7)
WIRING
1. Use illustration for proper connection.
2. Be sure to maintain speaker polarity.
3. Connect primary tabs on Mid-Range/Woofer to Amplifier.
4. Connect secondary tabs on Mid-Range/Woofer to Tweeter.
NOTE:
The tweeter has an integrated 6dB/octave HP crossover. The
mid-range/w
great acoustic crossover filtering.
oofer has natural roll-off characteristics exhibit
wing pages.
System Wiring
Mid-Range
Woofer
Specifications subject to change without notice.See figures on follo
Striped
From Midrange
Tweeter
(built-in 6dB
crossover)
From Amplifier
3
1/4”
(0.25”)
3/16”
(0.18”)
Page 4
SPECIFICATIONS
3.83
(97mm)
0.70
(17mm)
6.10
(154mm)
0.67
(17mm)
Specifications subject to change without notice.
4
Page 5
R152-S
2.13"
(54mm)
Component System
R152
Midrange
Mounting
5.41"
(137mm)
Holes
R1T
Tweeter
1.83"
(46mm)
Verify Scale
1.00"
(25mm)
Before Using
Template
1.00"
(25mm)
R152 Midrange Hole Cutout
4.76"
(121mm)
7
Page 6
R1652-S
2.13"
(54mm)
Component System
R1652
Midrange
Mounting
6.46"
(164mm)
Holes
R1T
Tweeter
1.83"
(46mm)
R1652 Midrange Hole Cutout
Verify Scale
1.00"
(25mm)
Before Using
Template
1.00"
(25mm)
5.81"
(147mm)
8
Page 7
L
IMITEDWARRANTYSTATEMENT
Rockford Corporation offers a imited warranty on Rockford Fosgate products on the fo owing terms:
Length of Warranty
Speakers – 1 Year (receipt required)
What is Covered
This warranty app ies on y to Rockford Fosgate products sod to consumers by Authorized Rockford Fosgate
Dea ers in the United States of America or its possessions. Product purchased by consumers from an
Authorized Rockford Fosgate Dea er in another country are covered on y by that country’s Distributor and
not by Rockford Corporation.
Who is Covered
This warranty covers on y the origina purchaser of Rockford product purchased from an Authorized
Rockford Fosgate Dea er in the United States. n order to receive service, the purchaser must provide
Rockford with a copy of the receipt stating the customer name, dea er name, product purchased and date of
purchase. Products found to be defective during the warranty period wi be repaired or rep aced
(with a product deemed to be equiva ent) at Rockford's discretion.
2.Any cost or expense re ated to the remova or reinsta ation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center
4.Any product which has had the seria number defaced, a tered, or removed
5. Subsequent damage to other components
6.Any product purchased outside the U.S.
7.Any product not purchased from an Authorized Rockford Fosgate Dea er
Limit on Implied Warranties
Any imp ied warranties inc uding warranties of fitness for use and merchantabi ity are imited in duration to the
period of the express warranty set forth above.Some states do not a ow imitations on the ength of an imp ied
warranty,so this imitation may not appy.No person is authorized to assume for Rockford Fosgate any other
iabi ity in connection with the sa e of the product.
How to Obtain Service
Contact the Authorized Rockford Fosgate Dea er you purchased this product from. f you need further
assistance, ca -800-669-9899 for Rockford Customer Service.You must obtain an RA# (ReturnAuthorization number) to return any product to Rockford Fosgate.You are responsib e for shipment
of product to Rockford.
EU Warranty
This product meets the current EU warranty requirements,see your Authorized dea er for detai s.
Rockford Fosgate
Rockford Corporation
600 South Rockford Drive
Tempe, Arizona 8528 U.S.A.
n U.S.A., (480) 967-3565
Customer Service -800-669-9899
www.rockfordfosgate.com
Rockford Fosgate and the Rockford Fosgate ogo are either
registered trademarks or trademarks of Rockford Corporation.
11/2009 E.R. (WebW zard)
1230-56133-01
20 0 Rockford Corporation.A rights reserved.
Pr nted n Ch na
Page 8
Page 9
Page 10
R1T-S
R1T-S
RF
Prime0.5
"4ohmtwaeter
Mfa
Date 07118116
UPC:7
80687
32996
9
~
iru
fuilii
~
m11
i
il
1
~
1
111
~lll
ll
lr
l tllll
~~
~~~~m~~
~
'
~~
1006723093·21
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.