Rockford Fosgate Punch PP4-T, PPB-T, Punch PP8-T Installation & Operation Manual
LJ
N
Pro
speakers
PP4-T
PPB-T
Serial
Number:
-------
Installation
Installation
lnstalacion
Einbau
lnstallazione
Date
of
et
y
funcionamiento
und
Betrieb
e
Purchase:
&
Operation
fonctionnement
funzionamento
-------
SAFETY
~CAUTION:
Before installation,
negative
to
the
(-)
terminal
unit, fire
PRACTICE SAFE
Continuous exposure
cause permanent hearing
may produce sound pressure levels well over
(I)
Punch Pro
Mounting hardware
Tweeter
INSTALLATION
Before beginning
I.
Be
sure
install these speakers.
2.
For safety, disconnect the negative
installation.
3. For easier assembly, we suggest you run
in
place.
4. Use
power
any
installation, follow these simple rules:
to
carefully read and understand
high
quality connectors
loss.
to
sound pressure levels over
loss.
High powered auto sound systems
sense
and practice
CARTON CONTENTS
CONSIDERATIONS
lead
from the battery prior
all
for
a reliable installation and
disconnect
to
and/or
possible injury.
the
prevent damage
SOUND™
IOOdB
130dB.
Use common
safe
sound.
the
instructions before attempting
to
wires prior
to
mounting your speakers
to
minimize signal
battery
may
beginning
to
the
or
:j~
',,/~/
/ _ _ Align Holes
I
.....
_____
,
,
Example of standard door installation
__
_
,
Think
before
5.
brake
vehicle.
6. Never run wires underneath
hull
area provides
7.
Avoid running wires over
grommets
I. Determine where
the
speaker
for
the
etc.) through their entire operating range
2. Refer
for your speaker model.
3.
Mark
4. Feed
5.
the
Be
sure
positive terminal
Tighten
over tighten the screws.
you drill! Be careful
or
hydraulic lines, vacuum lines
If
installation
to
speaker
to
the
the
locations for
speaker wires through
to
observe
the
in
a boat, take care
the
best protection.
or
protect
any
wires routed through metal, especially the firewall.
the
to
specification chart
screws until
speakers
mount
evenly.
to
fit;
if
mounting
The
the
mounting screws. Drill
proper
is
polarity when connecting
indicated with a red
the
the
through sharp edges. Use rubber
Be
template provided also gives the proper
speaker
not
to
cut
or
or
electrical wiring when working
not
vehicle. Running
drill into gas tanks,
to
cut
or
the
MOUNTING
will
be mounted. Ensure
sure
that
the
is
ring
snug
to
and
.
mounting location
ensure
the
proper
the
connect
in
place
in a door, operate
to
determine
the
cutout
fuel
drill
through
wires inside the vehicle
or
an
area large enough for
all
functions (windows, locks,
there
is
no obstruction.
diameter hole
holes with a
to
the
the
wires.
to
prevent rattling.
on
the
main
plastic
is
deep enough
to
cutout
1/8"
bit.
speaker terminals.
The
speaker's
Do
lines,
any
hull.
or
cut
size.
not
2
fEATURES
ICC
(Integrated
For
the
PP4-T
integrated into
This crossover
the
tweeter
crossover. Just connect
speaker,see
without the need
bel
and
PPS-T,
the
back cover
allows
ow
.
Concealed
Crossover)
the
crossover
of
the tweeter.
for easy connection
fo
r an external
the
terminals
at
is
the
of
Punch
Pro
Nominal
DiameterÂDescription
Nominal
Frequency
Crossover
Impedance
Response
Frequency
12dB/octave
Voice
Coil
Diameter-
Fs
-
Free
Air
Qts
Vas
-
cu
.
ft
.
(Liter)
Xmax-
inch
(mm)
SPL
(dB
@
1w
Power
Handl
i
Mounting
Mounting
Includes
Trim
Trim
Includes
Diameter-inch
Depth-inch
Grille/Trim
Ring
Diameter-inch
Ring
Height-inch
Adapter
Tweeters
inch
(mm)
(ohms)
(Hz)
(Hz)
Butterworth
Resonance
/1
ng-Watts
Crossover
inch
(Hz)
m)
(RMS
(mm)
(mm)
(mm)
(mm)
Plate
(mm)
I
Ring
Peak
SPECIFICATIONS
PP4-T
1.5
(38.1)
Pro
tweeter
40
4kHz-20kHz
4.5kHz
-
1.475
(37
.5)
3kHz
-
-
0.001
(0.25)
105d8
50
/
4.375
2.59
100
(111.00
(
65.8)
)
)
-
-
PP8-T
1.5
(38
.1)
Pro
tweeter
80
4kHz-20kHz
4.
5kHz
-
1.4
75
(37
.5)
3kHz
-
-
0.
001
(0.25
105dB
50/100
4.375
(111
.
00
2.
59
(65
.8)
-
-
)
)
- -
- -
See
figures
on
following
pages.
Specifications
subject
to
change
without
'
'
notice.
'
'
--- ----------
3
Loading...