® ®
car audio
component systems
for
fanatics
operation &operation &
operation &
operation &operation &
installationinstallation
installation
installationinstallation
Dear Customer,
Congratulations on your purchase of the world's finest brand of car audio speakers. At
Rockford Fosgate we are fanatics about musical reproduction at its best, and we are
pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that
reproduce music with all the clarity and richness you deserve.
For maximum performance we recommend you have your new Rockford Fosgate
product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized
training through Rockford Technical Training Institute (RTTI). Please read your
warranty and retain your receipt and original carton for possible future use.
Great product and competent installations are only a piece of the puzzle when it comes
to your system. Make sure that your installer is using 100% authentic installation
accessories from Connecting Punch in your installation. Connecting Punch has
everything from RCA cables and speaker wire to Power line and battery connectors.
Insist on it! After all, your new system deserves nothing but the best.
To add the finishing touch to your new Rockford Fosgate image order your Rockford
wearables, which include everything from T-shirts and jackets to hats and sunglasses.
To get a free brochure on Rockford Fosgate products and Rockford accessories, in the
U.S. call 602-967-3565 or FAX 602-967-8132. For all other countries, call +001-602967-3565 or FAX +001-602-967-8132.
PRACTICE SAFE SOUND™
CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB
CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUND
MAY
SYSTEMS
MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER
130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.
If, after reading your manual, you still have questions regarding this product,
we recommend that you see your Rockford Fosgate dealer. If you need further
assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial
number, model number and date of purchase available when you call.
The serial number can be found on the outside of the box. Please record it in
the space provided below as your permanent record. This will serve as
verification of your factory warranty and may become useful in recovering your
product if it is ever stolen.
Serial Number: ________________________________
Model Number:________________________________
T
ABLE OF
C
ONTENTS
Introduction................................................................................................ 1
Package Contents ....................................................................................... 1
Design Features .......................................................................................... 2
Installation Considerations ........................................................................... 4
Mounting Location ...................................................................................... 5
Installation ................................................................................................. 6
Troubleshooting........................................................................................ 10
Specifications ........................................................................................... 11
Warranty Information ................................................................................ 12
International Information............................................................................ 13
G
ETTING STARTED
Welcome to Rockford Fosgate! This manual is designed to provide information
for the owner, salesperson and installer. For those of you who want quick
information on how to install this product, please turn to the
Section
of this manual or refer to the icons listed below. Other information can
Installation
be located by using the Table of Contents. We, at Rockford Fosgate, have
worked very hard to make sure all the information in this manual is current. But,
as we are constantly finding new ways to improve our product, this information
is subject to change without notice.
I
® ®
N
S
T
A
L
L
A
T
I
O
N
Sections marked
INSTALLATION
include “slam dunk”
wiring connections
TROUBLE-
Sections marked
TROUBLESHOOTING
include recommendations for
curing installation problems
S
H
O
O
T
I
N
G
I
NTRODUCTION
This manual provides information on the features and installation of the
Fanatic X Systems. We suggest you save this manual for future reference.
We strongly recommend you have your Authorized Rockford Fosgate Dealer
install the Fanatic X System. If you do choose to install the system yourself,
please be sure to read the entire manual before beginning.
P
ACKAGE
C
ONTENTS
FNX1414
(2) FNX1401 Tweeters
Includes 3/4" [20mm] silk dome tweeter,
flush mount housing, surface mount housing,
wedge mount housing
(2) Tweeter Mounting Brackets
(4) #8 32 x .500 Screws
(4) #8 32 Black Nuts
(8) #8 x .75 Phillips Screws
(2) .110 Female Fast-on Connectors
(2) .110 Male Fast-on Connectors
(2) FNX1404 4" Midrange Speakers
(2) 4" Speaker Grilles
(2) 4" Speaker Grille Rings
(2) “RF” Speaker Grille Logos
(2) FNX142x 2-Way Crossovers
(8) #8 x 1.25 Phillips Screws
(20) 18 Gauge Speaker Wire
FNX1614F
(2) FNX1401 Tweeters
Includes 3/4" [20mm] silk dome tweeter,
flush mount housing, surface mount housing,
wedge mount housing
(2) Tweeter Mounting Brackets
(4) #8 32 x .500 Screws
(4) #8 32 Black Nuts
(8) #8 x .75 Phillips Screws
(2) .110 Female Fast-on Connectors
(2) .110 Male Fast-on Connectors
(2) FNX1406F 6" Midrange Speakers
(2) 6" Speaker Grilles
(2) 6" Speaker Grille Rings
(2) “RF” Speaker Grille Logos
(2) FNX142x 2-Way Crossovers
(8) #8 x 1.25 Phillips Screws
(20) 18 Gauge Speaker Wire
FNX1514
(2) FNX1401 Tweeters
Includes 3/4" [20mm] silk dome tweeter,
flush mount housing, surface mount housing,
wedge mount housing
(2) Tweeter Mounting Brackets
(4) #8 32 x .500 Screws
(4) #8 32 Black Nuts
(8) #8 x .75 Phillips Screws
(2) .110 Female Fast-on Connectors
(2) .110 Male Fast-on Connectors
(2) FNX1405 51⁄4" Midrange Speakers
(2) 51⁄4" Speaker Grilles
(2) 51⁄4" Speaker Grille Rings
(2) “RF” Speaker Grille Logos
(2) FNX142x 2-Way Crossovers
(8) #8 x 1.25 Phillips Screws
(20) 18 Gauge Speaker Wire
FNX1614
(2) FNX1401 Tweeters
Includes 3/4" [20mm] silk dome tweeter,
flush mount housing, surface mount housing,
wedge mount housing
(2) Tweeter Mounting Brackets
(4) #8 32 x .500 Screws
(4) #8 32 Black Nuts
(8) #8 x .75 Phillips Screws
(2) .110 Female Fast-on Connectors
(2) .110 Male Fast-on Connectors
(2) FNX1406 61⁄2" Midrange Speakers
(2) 61⁄2" Speaker Grilles
(2) 61⁄2" Speaker Grille Rings
(2) “RF” Speaker Grille Logos
(2) FNX142x 2-Way Crossovers
(8) #8 x 1.25 Phillips Screws
(20) 18 Gauge Speaker Wire
– 1 –
D
ESIGN FEATURES
4
5
6
2
3
1
10
9
12
11
Tweeter
1. 3/4" Silk Dome Tweeter – To ensure accurate high frequency reproduction, the
tweeter dome must be both light and strong. The Fanatic X Component Systems
use a silk dome that has extremely low mass and high strength for smooth high
frequency reproduction.
2. Ferrofluid Cooling – This synthetic fluid is held in place in the magnetic gap. It
bathes the voice coil allowing higher power handling and greater reliability.
3. Neodymium Magnet – What good would a tweeter be if it was too big to mount
in your favorite spot? The Fanatic Component Systems use a highly efficient
neodymium magnet to enable a very small tweeter to have very big performance.
– 2 –
7
8
D
ESIGN FEATURES
Midrange
4. Rubber Surround – The durable rubber surround withstands the
extremes of the automotive environment. It also improves sound quality
by reducing 2nd and 3rd order harmonics and provides wider frequency
response.
5. Mica Filled Polypropylene Cone – The ideal cone material would be
infinitely strong, very light and would have very high damping to ensure
great sound quality. The Fanatic X Series Component Systems use a
mica filled polypropylene cone that is strong, light and has high internal
damping to provide excellent reproduction of sound.
6. Cupped Spider – The spider has the job of centering the voice coil and
providing the rear suspension for the speaker. The Fanatic X Component
Systems use a durable cupped spider to ensure great sound with long
life and durability.
7. Large 1" Voice Coil with Anodized Aluminum Former – Just like all
Rockford Fosgate woofers, all Fanatic Component System midrange
drivers use an aluminum voice coil former for more efficient dissipation
of heat. Dissipating the heat is key to long life and high power handling,
so go ahead and crank it up!
8. Vented Pole Piece – The pole piece extends from the back of the speaker
into the voice coil area. The Fanatic X Component System uses a vented
pole piece to allow cool air to circulate in the voice coil gap which allows
greater power handling and increased reliability.
Crossover
9. 2 Way Butterworth Crossover – Features an 18dB per octave high-pass
crossover for the tweeter and a 6dB low-pass crossover for the midrange.
The steeper slope of the tweeter crossover gives better power handling.
The low-pass crossover provides a seamless transition between tweeter
and midrange.
10. Optical Compression – This built-in protection circuit limits power to the
tweeter when the “danger” threshold is exceeded. Because it simply
limits power and doesn't shut the tweeter off, this circuit is completely
inaudible.
11. Gold-Plated Screw Terminals – Terminals plated in gold for maximum
resistance to corrosion to ensure great sound for years to come. These
terminals accept bare wire or 1/4" spade lug connectors.
12. 0dB/–3dB Tweeter Pad – In some installations, you may find that the
tweeter location is much closer to your ears than the midrange. This pad
allows you to match the tweeter level to the midrange for the best
balance.
– 3 –
I
NSTALLATION
Tools Needed
The following is a list of some of the tools necessary for the installation of your
speakers.
Power Drill with assorted bits #2 Phillips Screwdriver
Tape Measure Voltmeter
General
1. For safety, disconnect the negative lead from the battery prior to beginning
the installation.
2. Never run wires underneath the vehicle. Running the wires inside the vehicle
provides the best protection.
3. Avoid running wires over or through sharp edges. Use rubber or plastic
grommets to protect any wires routed through metal.
4. Mount the speakers/crossovers away from electrical sources (other than the
amplifier) i.e., power cables, electronic fuel pumps, vehicle computers,
and other potential noise sources.
5. Mount the speakers/crossovers away from areas of extreme heat or
moisture.
Speakers
1. Make sure there is an area large enough for the speaker to mount. Warning!
Failure to do this can cause damage to the speaker if the speaker frame
is bent during installation.
2. Check to see that the location is deep enough for the speaker(s) and the
location does not interfere with the normal operation of the vehicle.
3. When mounting the speaker(s) in the door of a vehicle, make sure the
speaker(s) do not interfere with either the door or window operation.
4. When mounting the speaker(s) on the rear deck of the vehicle, check the
operation of the rear hatch or trunk lid. Make sure the torsion bars and other
moving parts are not obstructed by the speaker(s) installation.
• Please refer to the Specifications section of this manual for proper mounting
diameter and depth of the speaker(s).
C
ONSIDERATIONS
Crossovers
1. Make sure there is a flat area large enough for the crossover to mount.
2. For best results, mount the crossover(s) next to the amplifier for a decorative
finish to the installation and to provide an easy upgrade (no new wires to
run) for a bi-amp Rockford Fosgate system in the future.
– 4 –
M
OUNTING LOCATION
A solid front stage with a good image is one of the most difficult tasks to achieve
in a vehicle. No car has the optimum listening environment. This makes proper
sound staging very difficult to accomplish. Most speakers tend to be placed
where they will fit easily, as opposed to where they can perform the best.
mounting location of your speakers will have a great effect on the sound quality
of your stereo system. The special care taken to place the speakers will yield
many hours of listening enjoyment in return. Several important recommendations should be followed.
• Place the speakers where they have a direct
path to the listening area.
• For the best integration between the midrange
and tweeter, the tweeter should be placed
less than 2" from the midrange. (Figure 1)
• If you cannot place the tweeter less than 2"
from the midrange, then place the tweeter
more than 7" from the midrange. Placing
the tweeter 2"-7" from the midrange can
cause destructive interference (frequency
response problems) which will affect the
speaker's ability to reproduce the frequency range around the crossover
frequency of the system.
• Whenever possible, place the tweeter directly above or below the midrange
as this maximizes the imaging (point source) capability of the speakers.
(Figure 2)
Figure 1
The
2" or less
Figure 2-A
Figure 2-B
– 5 –
• Sound radiated from a “point source” has the most optimum stereo imaging
because the separation of the acoustical centers between the midrange and
tweeter for each channel is at the optimum. Figure 2-A describes a
horizontal speaker alignment. In a closed environment such as an
automobile, horizontal speaker alignment can cause severe amplitude and
phase differences which will degrade not only the imaging, but also the
frequency response. This is due to the path length differences between the
midrange and tweeter. Figure 2-B displays a vertical alignment between the
midrange and tweeter. With a vertical alignment, the path length difference
between the midrange and tweeter are reduced to a minimum. The result
is a negligible difference in path lengths between the midrange and tweeter
regardless of the proximity of the listener to the speakers. Mounting the
speaker with minimum path length difference will ensure the best staging
and imaging possible from your audio system.
I
NSTALLATION
Mounting the Midrange
I
® ®
N
S
T
A
L
L
A
T
I
O
N
1. Cut the proper size hole for the midrange/woofer.
• For the FNX-1404, cut an 90.48mm (39⁄16") diameter hole
• For the FNX-1405, cut a 113.50mm (415⁄32") diameter hole
• For the FNX-1406F, cut a 127mm (5") diameter hole
• For the FNX-1406, cut a 139.06mm (51⁄2") diameter hole
2. Place the mounting ring over the mounting hole and mark the location of
the screw mounting holes.
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.
4. Route the wire through the hole.
5. Place the mounting ring over the hole.
6. Attach the wires and be sure to observe the proper speaker polarity.
7. Place the speaker into the hole and screw the speaker into place. Be
careful not to bend the speaker frame during this step.
8. Press the speaker grille into the mounting ring.
– 6 –
Flush Mount Tweeter
I
® ®
N
S
T
A
L
L
A
T
I
O
N
Surface Mount Tweeter
Wedge Mount Tweeter
Flush
Housing
Surface
Housing
Tweeter
Tweeter
Trim Ring
Trim Ring
Back
Plate
Back
Plate
Tweeter
Wedge
Housing
– 7 –
Crossover Connections
-0db Tweeter Level
-3db Tweeter Level
- +-
+
+
TWEETERINPUT-MIDRANGE
+
–
+
(One channel of
amplifier)
–
• Be Sure to Maintain Speaker Polarity
• 0dB Tweeter Level matches the amplitude of the tweeter to the midrange
• –3dB Tweeter Level reduces the amplitude of the tweeter –3dB lower than
the midrange. (ex. ideal for tweeters located high in door panels and
midranges located low in the kick panel)
– 8 –
Bandpassing the Midrange
• The Fanatic Component Systems are optimized for full range music reproduction. In cases where a subwoofer is used, the midrange can be bandpassed in
order to prevent overlapping frequencies from the midrange into the
subwoofer.
1.Determine the frequency range that the subwoofer will play (i.e.: 20Hz-80Hz)
2.Use the low-pass crossover frequency of the subwoofer system (i.e.: 80Hz) as
the high-pass crossover frequency for the midrange
3.Select the appropriate capacitor value (i.e.: 500µF) to properly bandpass the
midrange
4.Place the capacitor in series with the “+” terminal of the speaker
I
® ®
N
S
T
A
L
L
A
T
I
O
N
- +-
+
+
TWEETERINPUT-MIDRANGE
C1
+
0dB
–3dB
–
Frequency Speaker
Hertz (4 ohms)
C1
80Hz 500µF
100Hz 400µF
130Hz 300µF
200Hz 200µF
260Hz 150µF
400Hz 100µF
Subwoofer Midrange Tweeter
80Hz
6dB/octave HP
– 9 –
T
ROUBLESHOOTING
Symptom Diagnosis Remedy
TROUBLE-
S
H
O
O
T
I
N
G
No sound from
speakers
Distorted sound
from speakers
Tweeters “burn
up” easily
Wires between amplifier,
crossover or speakers not
connected properly.
Amplifier has no output.
Speaker wires are shorted
to each other or to the chassis of the vehicle.
Speakers are blown.
Incorrect wiring between
crossover and speakers
Excessive power from amplifier
Equalizer in system (if
available) has excessive
boost in the high frequency
range
Check and repair or replace
wiring as needed.
Check system with known working amplifier and repair or replace as needed.
Check for shorts in the wiring
with a volt/ohm meter and repair or replace wires as needed
Check system with known working speaker and repair or replace as needed.
Check wiring and repair or replace as needed.
Check gain settings on amplifier and readjust as necessary
Check settings on equalizer and
readjust as necessary
Engine Noise from
One or More
Speakers
Speaker wires shorted to
chassis of vehicle.
Speaker wires are routed
near radiated noise source.
(Power cables, vehicle
computers, etc.)
Crossover is mounted near
radiated noise source.
(Power cables, vehicle
computers, etc.)
– 10 –
Check for shorts in the wiring
with a volt/ohm meter and repair or replace wires as needed.
Re-route speaker wiring away
from noise sources. (Refer to
the Installation Consider-
ations section of this manual.)
Move crossovers away from
noise sources. (Refer to the In-
stallation Considerations section of this manual.)
S
PECIFICATIONS
System Model Number FNX1414 FNX1514 FNX1614F FNX1614
Midrange Model Number FNX1404 FNX1405 FNX1406F FNX1406
Nominal Diameter 4" 51⁄4"6"6
1
⁄2"
Nominal Impedance 4Ω 4Ω 4Ω 4Ω
Frequency Response 90Hz-8kHz 60Hz-6kHz 61Hz-6kHz 50Hz-5kHz
Fs (Hz) 90Hz 60Hz 61Hz 50Hz
Qes .858 .507 .507 .545
Qms 4.363 3.303 3.330 3.508
Qts .717 .440 .439 .472
3
/liter) .08/2.4 .26/7.5 .31/8.8 .72/20.3
Vas (ft
Xmax (in/mm) .11/2.9 .15/3.7 .15/3.7 .15/3.7
Sensitivity 84.8dB 87.4dB 87.9dB 88.4dB
RMS Power Handling 70 Watts 70 Watts 70 Watts 70 Watts
Mounting Diameter 90.48mm 113.50mm 127mm 139.06mm
(39⁄16") (415⁄32") (5") (51⁄2")
Mounting Depth 54mm (21⁄8") 60mm (23⁄8") 63mm (215⁄32") 65mm (29⁄16")
Model FNX1401
Nominal Diameter 3/4" (20mm)
Nominal Impedance 4Ω
Frequency Response 1.8kHz-20kHz
Fs 1.8kHz
Sensitivity 93dB
RMS Power Handling 70 Watts*
Mounting Diameter See drawings
Model FNX142x
Crossover Type 2-Way
Crossover Frequency 4kHz @ 4Ω
Crossover Slope 18dB/octave High-Pass
6dB/octave Low-Pass
Filter Q 0.707 (Butterworth)
Tweeter Protection Optical Compression
Tweeter Pad 0dB/–3dB
Mounting Depth See drawings
*Power Ratings (PE) is established with recommended filter network
Wedge
Mount
1.562"
1.24"
Surface
Mount
1.795"
Flush
Mount
1.74"
1.94"
.675"
.965"
.25"
1.00"
.375"
1.00"
(Specifications are subject to change without notice)
L = 3.25”
H = 1.50”
– 11 –
L = 4.50”
- +-
+
+
TWEETERINPUT-MIDRANGE
L
IMITED
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following
terms:
• Length of Warranty
1 year on speakers 30 days on speaker B-stock (receipt required)
3 years on electronics 90 days on electronic B-stock (receipt required)
2 years on source units
• What is Covered
This warranty applies only to Rockford Fosgate products sold to consumers by Authorized
Rockford Fosgate Dealers in the United States of America or its possessions. Product
purchased by consumers from an Authorized Rockford Fosgate Dealer in another country
are covered only by that country’s Distributor and not by Rockford Corporation.
• Who is Covered
This warranty covers only the original purchaser of Rockford product purchased from an
Authorized Rockford Fosgate Dealer in the United States. In order to receive service, the
purchaser must provide Rockford with a copy of the receipt stating the customer name,
dealer name, product purchased and date of purchase.
• Products found to be defective during the warranty period will be repaired or replaced
(with a product deemed to be equivalent) at Rockford's discretion.
• What is Not Covered
1. Damage caused by accident, abuse, improper operations, water, theft
2. Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate
4. Any product which has had the serial number defaced, altered, or removed
5. Subsequent damage to other components
6. Any product purchased outside the U.S.
7. Any product not purchased from an Authorized Rockford Fosgate Dealer
W
Service Center
ARRANTY INFORMATION
• Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and merchantability are
limited in duration to the period of the express warranty set forth above. Some states do not
allow limitations on the length of an implied warranty, so this limitation may not apply. No
person is authorized to assume for Rockford Fosgate any other liability in connection with
the sale of the product.
• How to Obtain Service
Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA#
(Return Authorization number) to return any product to Rockford Fosgate. You are
responsible for shipment of product to Rockford.
Ship to: Electronics
Rockford Corporation
Warranty Repair Department
2055 E. 5th Street
Tempe, AZ 85281
RA#:_________________
Ship to: Speakers
Rockford Acoustic Design
(Receiving-speakers)
609 Myrtle N.W.
Grand Rapids, MI 49504
RA#:_________________
– 12 –
INTERNATIONAL
I
NFORMATION
– 13 –
LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTALACIÓN DEL
PRODUCTO.
I
NTRODUCCIÓN
Este manual contiene información sobre la construcción, installación y
funcionamiento de los sistemas Fanatic X. Le recomendamos que conserve el
manual para futuras consultas.
Es preferible que la instalación de sistema Fanatic X sea realizada por un
distribuidor autorizado Rockford Fosgate. Si prefiere realizar la instalación usted
mismo, asegurese de leer el manual en su totalidad antes de comenzar.
M
ONTAJE
• Le mejor interacción entre tweeter y medio
se consigue si no están separados entre si
más de 5 cenimetros. (Figura 1)
no superior a 5cm
Figura 1
ESPAÑOL
I
NS TALACIÓN
Montaje del altavoz de medios
– 14 –
I
® ®
N
S
T
A
L
L
A
T
I
O
N
1. Corte el agujero para el medio/woofer.
• Par el FNX1404, corte un circulo de 90,48mm de diámetro
• Par el FNX1405, corte un circulo de 113,50mm de diámetro
• Par el FNX1406F, corte un circulo de 127mm de diámetro
• Par el FNX1406, corte un circulo de 139,06mm de diámetro
2. Use los anillos de montaje de plástico como plantilla. Marque la posición de
los tornills de anclaje.
3. Quite el anillo y perfore los agujeros con una broca de 1/8".
4. Pase el cable de altavoz a través del agujero.
5. Monte el anillo de montaje sobre el agujero.
6. Conecte los cables observando la polaridad. Mantenga los cables alejados pe
partes móviles o cortantes.
7. Asegure el altavoz en la abertura con los tornillos. Tenga la precaución de no
doblar el marco del altavoz en este proceso.
8. Presione la rejilla en el anillo de montaje.
Conexiones del Crossover
Nivel de 0dB
del Agudo
Nivel de –3dB
del Agudo
I
® ®
N
S
T
A
L
L
A
T
I
O
N
- +-
+
+
TWEETERINPUT-MIDRANGE
+
–
+
(Un canal del
amplificador)
–
• Asegúrese de mantener la polaridad de los parlantes
• Nivel de 0dB del Agudo cuadra con la amplitud del Agudo al Mediorango
• Nivel de 3dB del Agudo reduce la amplitud del Agudo
–3dB más bajo que el mediorango. (Ej. Ideal para agudos colocados en paneles
de puerta elevados y mediorangos localizados en paneles bajos (kick panel)).
– 15 –
Veuillez lire les instrucitons suivantes pour l'installation de ces produits.
I
NTRODUCTION
Ce manuel contient des informations sur les caractéristiques et l'installation des
systèmes Fanatic X. Nous vous proposons de garder ce manuel pour toute
référence future.
Nous vous recommandons vivement de faire installaer votre système punch
Fanatic X par un dealer agréé Rockford Fosgate. Si vous choisissez d'installer le
système vous même, assurez-vous de lire ce manuel entièrement avant de
commencer.
E
MPLACEMENT DE
M
ONTAGE
• Pour bénéficier d'une harmonie maximum
entre le médium et l'aigu l'éloignement
entre ces deux haut-parleurs devrait être de
moins de 5cm
moins de 5 cm entre les 2 chassis. (Figure 1)
Figure 1
I
NSTALLATION
Montage du haut-parleur médium
FRANCAIS
I
® ®
N
S
T
A
L
L
A
T
I
O
N
– 16 –
1. Découper un trou adapté au haut-parleur médium/woofer.
• Pour le FNX1404, le diamètre du trou est de 90,48mm
• Pour le FNX1405, le diamètre du trou est de 113,50mm
• Pour le FNX1406F, le diamètre du trou est de 127mm
• Pour le FNX1406, le diamètre du trou est de 139,06mm
2. Placer l'anneau de montage sur le trou et repérer l'emplacement des trous des vis.
3. Retirer l'anneau. Percer les trous des vis en utilisant une mèche de 3mm.
4. Faire passer les fils dans le trou central.
5. Placer l'anneau de montage au-dessus du trou central.
6. Connecter les fils au haut-parleur en respectant les polarités. Eloigner les fils de
toute partie tranchante ou mobile du véhicule.
7. Placer le haut-parleur au-dussus du trou central. Visser le haut-parleur dans son
emplacement. Faire attention à ne pas tordre le chassis du haut-parleur
durant cette étape de montage.
8. Mettre la grille dans l'anneau de montage.
Connexion du filtre
Niveau de l’aigu –3dB
Niveau de l’aigu 0dB
(Un canal de
l’amplificateur)
- +-
+
+
TWEETERINPUT-MIDRANGE
+
–
+
–
• Vérifier les polaritées des haut-parleurs
• 0dB Pas d'atténuation de l'aigu par rapport
• –3dB d'atténuation du niveau de l'aigu –3dB d'atténuation par rapport au
médium. (Ex: Idéal pour le positionnement de l'aigu en haut de portière et le
mèdium en bas ou “kick panel” Volume de charge créer en bas de port ou dans
l'angle de celle-ci, au niveau des pieds.
– 17 –
Die folgende Bedienungsanleitung soll Ihnen beim Einbau eine Hilfestellung
geben.
E
NLEITUNG
Diese Bedienungsanleitung enthält Informationen für den Gebrauch und Einbau
des Punch Fanatic X Systems. Wir empfehlen, diese auch für Fragen in der Zukunft
sorgfältig aufzubewahren.
Es ist empfehlenswert, sich das Fanatic X System von einem Autorisierten
Rockford Fosgate Fachhändler einbauen zu lassen. Sollten Sie den Einbau
jedoch selber vornehmen wollen, so empfehlen wir Ihnen, die Bedienungsanleitung
sorgfälitg zu lesen.
E
INBAUORT
• Für das optimale Zusammenspiel von Mittelund Hochtöner, sollte der Hochtöner niemals
weiter als 5cm vorn Mitteltöner entfernt
Abstand max. 5cm
montiert werden. (Abb. 1)
E
INBAU
Montage des Mitteltöners
– 18 –
(Abb. 1)
I
® ®
N
S
T
A
L
L
A
T
I
O
N
DEUTSCH
1. Schneiden Sie die richtige Lochgröβe für den Mitteltöner oder Midbaβ aus.
• Für den FNX1404, schneiden Sie ein 90,48mm Ø Loch
• Für den FNX1405, schneiden Sie ein 113,50mm Ø Loch
• Für den FNX1406F, schneiden Sie ein 127mm Ø Loch
• Für den FNX1406, schneiden Sie ein 139,06mm Ø Loch
2. Setzen Sie den Montagering auf das Loch und markieren Sie die Löcher
für die Schrauben.
3. Nehmen Sie den Ring wieder ab und bohren Sie dann, mit einem
passenden Bohrer, die Schraubenlöcher vor.
4. Führen Sie das Kabel durch das Loch.
5. Plazieren sie den Montagering über dem Loch.
6. Schlieβen Sie die Lautsprecherkabel an. Kontrollieren Sie, ob die Polarität
stimmt. Stellen Sie sicher, daβ das Lautsprecherkabel an keinen scharfen
oder sich bewegenden Teilen anliegt.
7. Plazieren Sie den Lautsprecher im Loch und befestigen Sie diesen. Seien
Sie dabei sehr vorsichtig, so daβ sich der Lautsprecherkorb nicht verzieht.
8. Drücken Sie das Lautsprechergitter im Montagering fest.
Frequenzweichen Anschlüsse
0dB
Hochtonabsenkung
–3dB
Hochtonabsenkung
+
- +-
(Ein Kanal des
Verstärkers)
• Achten Sie auf die Lautsprecherpolarität
• 0dB Hochtonabsenkung stimmt mit der Lautstärke des Mitteltöners überein
• –3dB Hochtonabsenkung, reduziert die Lautstärke des Hochtöners gegenüber der
Lautstärke des Mitteltöners. –3dB leiser, als der Mitteltöner (Ideal für Einbauten, bei
denen die Hochtöner im Armaturenbrett und die Mitteltöner in Fuβraum eingesetzt
werden.
+
TWEETERINPUT-MIDRANGE
+
–
+
–
– 19 –
Leggere le istruzioni seguenti prima dell'installazione del prodotto.
I
NTRODUZIONE
Questo manuale fornisce informazioni sulle caratteristiche e sul installazione dei
sistemi Fanatic X. Vi suggeriamo di conservare questo manuale come riferimento
futuro.
Raccomandiamo fortemente che is sistema sia installato dal vostro rivenditore
Rockford Fosgate. Se scegliete di procedere con l'installazione da soli, leggete
attentamente tutto il manuale prima di proseguire.
P
OSIZIONAMENTO
• Per ottenere la miglior integrazione tra tweeter
e midrange, vi suggeriamo di posizionare i
due componenti a meno di 5 cm tra loro.
meno di 5 cm
(Figura 1)
Figura 1
I
NSTALLAZIONE
Installazione del Midrange
– 20 –
I
® ®
N
S
T
A
L
L
A
T
I
O
N
ITALIANO
1. Practicate un foro del diametro corretto per il midrange/woofer
• 90,48mm per FNX1404
• 113,50mm per FNX1405
• 127mm per FNX1406F
• 139,06mm per FNX1406
2. Posizionate l'anello della griglia sul foro e segnate la posizione delle viti.
3. Togliete l'anello e forate il pannello con una puna da 3,5mm.
4. Passate i cavi attraverso il foro.
5. L'anello della griglia sopra il foro dell'altoplarlante.
6. Collegate i cave assicurandovi di osservare la corretta polarità. Assicuratevi di
mantenere i cavi lontano da parti in movimento o strutture taglienti.
7. Posizionate l'altoparlante nel foro ed avvitatelo. Assicuratevi di non piegare
il cestello dell'altoparlante.
8. Incastrate la griglia sull'anello di fissaggio.
Connessioni del crossover
-0db livello tweeter
-3db livello tweeter
(Un canale
dell’amplificatore)
+
- +-
+
TWEETERINPUT-MIDRANGE
+
–
+
–
• Assicuratevi di mantenere la corretta polarita degli altoparlanti
• 0dB di livello del tweeter accoppia la sensibilita del midrange a quella del tweeter
• –3dB di livello del tweeter riduce l'efficienza del tweeter 3dB meno del midrange
(es.: ideale per tweeter posizionati nella parte alta delle portiere e midrange molto
bassi nelle tasche)
– 21 –
N
OTES
– 22 –
N
OTES
– 23 –
N
OTES
– 24 –
1/98
LIT9944
MADE IN THE USA
This product is designed, developed and assembled in the USA by a dedicated
group of American workers. The majority of the components used in the
construction of this product are produced by American companies. However,
due to the global nature of their manufacturing facilities and the loudspeaker
parts industry in general, some parts may be manufactured in other countries.
Rockford Fosgate
Rockford Corporation
546 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A., (602) 967-3565
In Europe, Fax (49) 8503-934014
In Japan, Fax (81) 559-79-1265
Loading...