Robus RPR180PIR-01, RPR180PIR-04 Installation Instructions

INSTRUCTION MANUAL

PROTON 180 DEGREE IP54 PIR, WHITE, COMPLETE WITH ACCESSORY
SHIELD TO REDUCE DETECTION ANGLE, MANUAL OVERRIDE

RPR180PIR-01 RPR180PIR-04

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of
this product, consult a competent electrician
Note:
Product technical information and specification may change over time without prior notification. For the latest technical
information please visit our web site www.ledgrouprobus.com.au

-20°C < Ta < +40°C, 220-240V~50/60Hz, Class II, IP54
Rated load:
Incandescent: Max. 1200W, Fluorescent / LED: Max. 300W
Mounting Height: 1.8m to 2.5m
Detection Range: 12m

Lux Level Adjustment: 3-2,000 Lux
Time Delay: 10 (±3) Seconds - 15 (±2) Minutes
Suitable for mounting on a normally flammable surface.

EN

Installation

1. Ensure mains supply is switched off before commencing work.

2. Select suitable location for mounting the sensor.

3. Remove the screw and then remove back plate.

4. Introduce cables.

5. Mark appropriate fixing hole positions on the wall, check location of buried cables, pipes and other building services before
drilling.

6. Attach plate to the wall using screws provided, ensure it is secure. When corner mounting please see pictogram 3.

7. Connect the cables as per figure 5. Live In (Brown) to L, Live Out (Brown) to L’ and Neutrals to N.

8. Attach sensor to back plate, ensure it is secure .

9. Adjust the angle of sensor and sensor settings.

Test:

Walk testing can be carried out to determine detection area with slow walking pace. When the sensor detects movement, the
load will be switched on for the pre-set time. For the walk test turn Lux control toward the Sun position (Max) and set time delay
to 10s. When finished, set controls to desired levels. Note: Once sensor has been triggered, subsequent detection restarts
timing period from beginning, so light stays on until set time elapses after last triggering.

ADJUSTING THE LUX CONTROL LEVEL:

The Sun position (2000 Lux) denotes that when there is movement the load will be switched on during the day and at night. The
minimum Lux setting 3 Lux means that the load will be turned on by sensor only at night. Lux settings can be adjusted from 3 –
2000 Lux by rotating the dial.

ADJUSTING THE TIME DELAY:

The Time Delay is “the length of time that the sensor switches the load ‘on’ after
activation”. The duration time can be adjusted from 10 (±3) seconds to 15 (±2) minutes.

Manual Override Function

The PIR can be on permanently for 8 hours. Using the switch on the wall perform 2 Off/ On, Operations within 4 seconds, the
light will stay on for 8 hours. In order to revert to AUTO detect mode, turn the sensor off and then, the light will turn off (AUTO).

The Installation must be carried out by a qualified electrician

LED Group Australasia
9/210 Queensport Road North Tel: [phone]
Murarrie Fax: [phone]
QLD 4172 Email: [e-mail]
Australia Website: www.ledgrouprobus.com.au

Issue 1 080818 Page 1

80mm

118mm

Accessory shield

51mm

1 2

RPRBRK-01
RPRBRK-04

3 4

30S

30 300

3

Lux

90S 3Min

10S

Time

7Min

15Min

1.8-2.5m

Max 6m

Max 12m

4

5

Page 2