Compact 28W 2D
Emergency Surface Fitting
RC282DEPO-01
C/W Opal and Prismatic diffuser, white Base
RC282DEPO-04
C/W Opal and Prismatic diffuser, black Base
Please read instruction before commencing installation and
retain for future reference.
Specication:
Installation:
Model No:
Operating mode
Supply Voltage:
Power Consumption:
Cap type:
Colour Temperature:
CRI:
Power Factor:
Operating Temp Range:
Ballast lumen Factor:
Battery
Battery Life
Discharge Duration
Operating temp Range:
IP Rating:
Safety Classification:
Diameter:
Depth:
Weight:
Warranty:
Suitable for mounting on a normally flammable surface
Green LED indicates correct battery charging mode
Safety and performance in accordance with EN60598-1,EN60598-2-22,
EN50082-1,EN61000-3-2,EN61000-3-3
Suitable for Indoor or outdoor use, wall or ceiling mounted.
!Electrical products can cause death or injury, or damage to property. If in any doubt
about the installation or use of this product, consult a competent electrician.
RC282DEPO-01/04
Maintained or non-maintained
220/240V50Hz
28W
GR10q
3500k
>80
0.99
5°C < ta < 25°C
0.15 Emergency Mode
4.8V x 4Ah Ni-Cd cells
Greater than 4 years normal use
>3 hours after minimum 24Hr charge
-5°C < ta < 25°C
65
Class I
284
87
2.2kg
1 Years
1. Ensure mains supply is switched off before commencing work.
2. Remove cover and gear tray and drill out relevant cable entry point
3. Mark appropriate fixing points on wall or ceiling; check that fixings will not impinge on
concealed cables of pipes before drilling holes.Where fitting must be weatherproof, apply
silicon sealant to fixings.
4. Fit cable gland (if weatherproofing necessary) and introduce supply cable. (Normally, the
emergency fitting must be powered from the lighting circuit feed)
5. Write installation date on battery
6. Connect wires from unswitched supply, brown to L, Blue to N and green/yellow to earth
marked terminals on gear tray. for lamp always on, link L to terminal “mains”, for lamp
switched, connect switched live wire to terminal “mains”
Note: if mains terminal not connected, fitting works as non-maintained emergency
luminaire
7. Fix gear tray in position and refit cover.
8. Switch on supply: In the non-maintained unit the green led should come on indicating
correct battery charge has started. The lamp only lights if the mains supply fails.
In the maintained unit, the green led will come on indicating correct battery charge has started and
the lamp will light (if switched live on). When supply to the unswitched live is lost, battery will
operate lamp in emergency mode (at reduced light output)
SWITCHING AND OPERATION INFORMATION FOR ROBUS LIGHTING PRODUCTS
ROBUS lighting products are suitable for use with standard switch, pull cord, retractive switch and PIRs, however
certain guidelines should be adhered to in order maximise lamp and fitting life.
Estimated average lamp life claims are based on switching cycles of 2 ¾ hours on, ¼ hour off. Switching cycles of
shorter duration may affect lamp and ballast life significantly.
To reduce the detrimental effect of short switching cycles, fittings should be left on or controls set to a minimum of 15
minutes, preferably 30 minutes, but even these time delay periods may reduce average lamp/ballast life.
Damaged lamps should be replaced promptly. A damaged lamp left unchanged for a long period can lead to control
gear damage.
These fittings are not suitable for installation where ambient air temperature is above 25°C
Note:
Product technical information and specification may change over time without prior notification. For the latest
technical information please visit our web site www.ledgrouprobus.com or www.robusdirect.com
Issue 6 160414
Page 1
Testing:
The emergency lighting must be inspected and tested regularly in accordance with local
codes of practice: note: for safety reasons tests should be carried out during daylight
hours.
The minimum recommended test schedule is as follows:
After installation, allow 24 hours to ensure full battery charge and then interrupt the
supply; check before 3 hours that lamps are still lighting.
1. Daily check that charge indicator LED is working
2. Monthly, interrupt mains for a short period and check lamps are on in emergency mode
3. Annual 12 month check, full duration test. Interrupt mains supply, lamps will light and
should remain on for a minimum 3 hours operation: batteries must be replaced when
they can no longer support 3 hour operation.
5. Complete record sheet on installation and retain in maintenance file.
6. Update file with ongoing test records for inspection by fire officer or other duly
authorised person
Installation and Maintenance Record:
Installer
Installation Type
Installation test duration & Date
Month
1
2
3
4
5
6
7
8
9
10
11
12
Test
Short
Short
Short
Short
Short
Short
Short
Short
Short
Short
Short
Short
3Hr.
Signed
1st Year
Date
Signed
2st Year
Date
3st Year
Signed
Information for the Product user
Date
4st Year
Signed
Date
5st Year
Signed
Date
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household
waste (WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a
collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are
purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly.
It is important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal
household waste, but should be disposed of according to local WEEE regulations
The Installation must be carried out by an electrician
LED Group
Western Retail Park
Nangor Road
Dublin 12
Ireland
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@led.ie
Website: www.led.ie
ISO 9001:2008
QUAL IT Y ASS U RE D CO MPANY
Page 2
Installation diagram:
Ø285 mm
86 mm
SL PL N
SL PL N
Wiring Details
Non-maintained Installation
Figure 1
Figure 3
mains lighting fuse
L
N
Figure 2
Diffuser
Figure 4
To mains lighting
Maintained or sustained
installation
The Installation must be carried out by an electrician
LED Group
Western Retail Park
Nangor Road
Dublin 12
Ireland
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@led.ie
Website: www.led.ie
Tamper proof test switch
mains lighting fuse
L
N
Tamper proof test switch
Maintained lighting control switch
To additional emergency luminaires
non-maintained
N
emergency luminaire
PL
To mains lighting
To additional emergency luminaires
Maintained LED
emergency luminaire
ISO 9001:2008
QUAL IT Y ASS U RE D CO MPANY
Page 3
Loading...