! Electrical products can cause death or injury, or damage to property. This product must
be installed only by a competent electrician.
1 Ensure mains supply is switched off before commencing work.
2 If necessary cut LED strip to the required length at the locations marked on the strip
(Every 5 LED’s),
3 Using the supplied end-cap & glue, glue the end-cap onto the end of the strip. Ensure
the end-cap is secure and sealed.
4 Mounting the strip,
a. Self adhesive strip, remove the protective cover to reveal adhesive strip. Place the \
strip onto the desired location and press down firmly. Ensure the strip is secure.
b.Clips: use a minimum of 4 clips per metre. Place the strip along the desired
position. Mark the locations of where the clips are required, keeping them equally
spaced. Fix clips to surface using self adhesive strip or screws. Pull cable tie
tightly on to strip, ensure the strip is secure, cut-off excess cable tie.
5 Mark the appropriate mounting positions on the surface; check that fixings will not
impinge on concealed cables or pipes before drilling.
6 The provided accessories “cable pin end” has stated that “Top 1” and “Top 2”, which
should match the same mark on strips. please ensure the correct pin insert the strips.
7 Connect the strips to 100W power supply (RKPS100) use the “cable pin end” which
included with the strips, and then connect with power supply,IP box (RKIPB1) will use
for connection between strips and power supply.
8 Each 10 meter strips can be controlled by 1pcs 100w power supply (RKPS100).
9 The provided accessory Repeater (RK1PRPT1), will extended to another 10 meter
strips (repeater will operate with RKPS100). solve the problem which caused by power
limitation and long transmitting distance.
Specification:
Installation:
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE
marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre
for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is
important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household
waste, but should be disposed of according to local WEEE regulations
R10MIP-WW, R5MIP-WW,
R10MIP-07,R5MIP-07
R10MIP-CW,R5MIP-CW
WARM WHITE, BLUE AND COOL WHITE CUTTABLE LED
STRIP KIT
Please read instructions before commencing installation and
retain for future reference.
Protection against electric shock: Class III (Safety extra low voltage)
Dimensions:
Strip length 10m; 5m strips
Depth 5.5mm
Width 15mm
Temperature range: -20°C < ta < 40°C
Ingress protection: IP65
Supply: 24V DC
Suitable for mounting on normally flammable surface
Warning! To prevent overheating, the fitting or driver must not be covered by
thermal insulation.
Complies with EN60598 (BS4533)
24
VDC
1
Issue 2 280910
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: +353 1 7099000
Nangor Road Fax: +353 1 7099060
Dublin 12 Email: info@led.ie
Ireland Website: www.led.ie
Page 1
ISO 9001:2008
QUAL IT Y ASSU RED CO MPAN Y
POWER SUPPLY
(RKPS100)
POWER SUPPLY
(RKPS100)
REPEATER
(RKRPT1)
CUT RGB AT POINT INDICATED
AND JOIN WITH CHOICE OF CONNECTORS
USE HEAT SHRINK AND GLUE FOR IP65
Included with 5m and 10m roll
Also sold separately
JOINER KIT
RKPCI
RKPCL
RKPCT
RKPCX
RKPC2
Includes
End cap and HS
X1
X1
X1
X1
X2
10m max
to go beyond 10m use repeater
plus appropriate power supply
for increments of 10m
(No overall Max length)
IP B OX O PT IO N A L FO R D EC OD ER A ND R EP EA TE R.
CUT AND JOIN
EASY TO
product code 1m~10m 11m~20m 21m~30m 31~40m
RKPS100
1 2 3 4
0 1 2 3
1X10m 2X10m 3X10m 4X10m
R10MIP-WW/07/CW
RKRPT1
I P B O X O P T I O N A L F O R D E C O D E R A N D R E P E A T E R .
RKPS100
REFERENCE CODE PRODUCT PRODUCT
R10M IP-WW/07/CW
RKRPT1
RKIPB1
10 0w p ow er s up pl y
10 m Cu tt ab le W W/ 07 /C W
5m C ut ta bl e WW /0 7/ CW
Jo in er K it
R5M IP-WW/07/CW
Jo in er K it
IP 65 b ox f or C ab le c on nection(small)
RKIPB2
IP 65 b ox f or D ec od er o r repeater
Re pe at er
IP BOX(RIPB2)
IP BOX(small)
(RKIPB1)
Installation diagram:
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: +353 1 7099000
Nangor Road Fax: +353 1 7099060
Dublin 12 Email: info@led.ie
Ireland Website: www.led.ie
Page 2
ISO 9001:2008
QUAL IT Y ASSU RED CO MPAN Y
Loading...