Robus R1230LEDCW-01, R1230LEDDW-01 Instruction Manual

Issue 2 080715

30W LED PANEL LIGHT,
300X1200MM, WHITE TRIM

R1230LEDCW-01
R1230LEDDW-01

1. Ensure mains supply is switched off before commencing
work.

2. Remove 300 x 1200mm tile from ceiling.

3. Ensure the area above the fitting is free from obstacle
pipes cable tray etc.

4. Connect plug to AC supply

5. Ensure the connections going to and from the driver
are secure.

6. Place connector, drivers and cable into the ceiling void.

7. Offer luminaire up to the ceiling void and manoeuvre into
final position similar to standard ceiling tile.

8.This product has no user serviceable parts. If any part is
damaged, disconnect from mains and discontinue use.

Page 1

The Installation must be carried out by an electrician

INSTRUCTION MANUAL

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or
use of this product, consult a competent electrician
Note:
Product technical information and specification may change over time without prior notification. For the latest
technical information please visit our web site www.ledgrouprobus.com.au

LED Group ROBUS Australia
9/210 Queensport Road North Tel: [phone]
Murarrie Fax: [phone]
QLD 4172 Email: [e-mail]
Australia Website: www.ledgrouprobus.com.au

Model No.
Voltage:
Power:
Lumen:
CCT:
CRI:
Beam Angle:
PF:
Ta Range:
IP Rating:
IK Rating:
Safety Class:
Dimensions:
Depth:
Weight:
Warranty:
Installation:

Complete with flex and AU plug
Suitable for mounting on normally flammable surface
Minimum distance from illuminated object is 0.5 metre
Driver must never be “hot-plugged” or connected to the
fitting when live.
Doing this may damage the fitting and will void the warranty.
Complies with EN 60598-1, EN 60598-2-2, IEC 62471-2, IEC
62778, IEC 62493, IEC 61347-1, 61347-2-13

R1230LEDCW-01
220-240V~50/60Hz
30W
2800lm
4000K
80
110

o

0.9

-20°C < ta < +45°C
20
06
Class II for the driver
295mm X 1195mm
9mm

3.8Kg
5 year
Recessed mounted,
Box mounted,
Suspended

R1230LEDDW-01
220-240V~50/60Hz
30W
3150lm
5000K
80
110

o

0.9

-20°C < ta < +45°C
20
06
Class II for the driver
295mm X 1195mm
9mm

3.8Kg
5 year
Recessed mounted,
Box mounted,
Suspended

Specifications

Installation

ISO 9001:2008

QUAL IT Y ASSU RE D CO MPANY

Warning:

Luminaire marked as NON-IC according to ASNZS60598-2.2.
Not suitable for use on residential properties.
DO NOT COVER OR ABUT. Any insulation material must be
positioned at a minimum distance of 100 mm from the fitting.

Caution:

Recessed Luminaires may pose an increased risk of fire
or property damage if not installed according to the
instructions provided.

Safety Instructions

Luminaires not suitable for
covering with thermally
insulating material.

Joist

Driver

SCB

HCB

MIC

SCI

DANGER - RISK OF FIRE

- Shall not be installed in residential premises

SCI = 100mm MIC = 100mm
SCB = 50mm HCB = 25mm

1195mm

Remove 300 x 1200 tile from ceiling.

295mm

9mm

Page 2

1 2

3 4

5

ISO 9001:2008

QUAL IT Y ASSU RE D CO MPANY

The Installation must be carried out by an electrician

LED Group ROBUS Australia
9/210 Queensport Road North Tel: [phone]
Murarrie Fax: [phone]
QLD 4172 Email: [e-mail]
Australia Website: www.ledgrouprobus.com.au

Installation diagram

2m

580mm

400mm