Robus L180B-04, L180B-01 Installation Instructions

Motion Detector 180

PIR

L180B-01 & L180B-04

Please read instruction before commencing installation and retain
for future reference.

°

Specification:

Installation:

Stand alone Passive infra-red sensor switch (PIR). Replacement for standard
single gang wall switch. Energy saving lighting control, which is ideal for indoor,
outdoor and wall.
Electrical Protection:
Supply:
Output Load:

Operating Temp:
Dimension:
Weight:
Detection range:

Delay time:
Light Level Adjustment:
IP:
Terminals suitable for cable sizes from 0.75mm2 to 1.5mm2.
Suitable for mounting on normally flammable surface
Note:
Product technical information and specification may change over time without prior
notification. For the latest technical information please visit our web site
www.ledgrouprobus.com or www.robusdirect.com

! Electrical products can cause death or injury, or damage to property. If in any
doubt about the installation or use of this product, consult a competent electrician.

1. Ensure mains supply is switched off before commencing work.

2. Choose suitable location for mounting the sensor, optimum mounting height is
approx 2.5m above ground level.

3. When cutting or drilling holes ensure not to impinge on buried cable or pipe work.
Avoid: positions close to exhaust gas flues, heat extraction vents, shrubs and trees
avoid false triggering. Also avoid pointing toward bright lights which may prevent
operation (or cause hunting i.e. flashing lights on and off) when Lux level set for night
operation.

4.Remove back plate by undoing the 2 screws visible from the front

5.Fix back plate to wall

6.Connect supply brown wire to L in,connect switch live to L out and connect blue wire
neutral to N.An earth is not required to operate this sensor,however it is possible to use
the earth terminal as a looping point

7. Set Lux control to day or sun position and Time to minimum (-).

8. Put switch in the on position and attach sensor to wall.

9. Switch on mains supply: The sensor will warm-up for approx 30~60 seconds and then
switch to auto detection mode.

Class II (no earth required)
220V~240V 50/60Hz
Max. 1,000W Incandescent lamp,
300W Fluorescent, 150W LED
5°C < ta < 40°C
Height: 75mm, Width: 85mm, Depth: 95mm

0.26Kg
180° Detection Angle, 12m Range,

2.5m Max Mounting Height
Adjustable time delay 10 seconds ~ 4 minutes
Daylight to night adjustable
IP44

Walk testing can then be carried out to determine detection area with slow walking pace.
When the sensor detects movement, the load will be switched on for the preset time.
Tilting the head downward will reduce detection range.When detection field is satisfactory,
set light level and delay time. Turning the Lux control toward the moon position will stop
switching action during bright daylight (for energy saving). To increase on time turn time
control towards +, max time delay 4 minutes. Note: once sensor has been triggered,
subsequent detection restarts timing period from beginning, so light stays on until set time
elapses after last triggering.

Information for the Product user

1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked
with crossed out wheelie bin symbol).

2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste
electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.

3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important
that it is separated from normal household waste and recycled in the WEEE chain

4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but
should be disposed of according to local WEEE regulations

The Installation must be carried out by an electrician

LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [e-mail]
Ireland Website: www.led.ie

Issue 2 150414

ISO 9001:2008

Q U AL IT Y A S SU RE D C O M PA N Y

Page 1

Installation diagram:

95mm

75mm

drill hole
(Introduction hole)

85mm

Figure 2

Figure 4

SENSOR

(Black)

(Blue)

(Brown)

LL

LAMP

N

220-240V AC

Figure 1

Figure 3

Detection Angle: Detection Range:

o

180

Figure 5

The Installation must be carried out by an electrician

LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [e-mail]
Ireland Website: www.led.ie

2.5m

12m(max)

Figure 6

ISO 9001:2008

Q U AL IT Y A S SU RE D C O M PA N Y

Page 2