CN-X1
Glassbot
User Manual
Multi Surface Cleaning Robot
1
2
About Window Cleaning Robot
GlassBot is a cleaning robot that works on multiple surfaces of glasses, tiles, smooth walls
and tables. It works with a built-in vacuum motor that helps it suck air and stand on the
glass surface. An embedded UPS (Un-interrupted Power System) prevents the robot
falling from the window even when no electrical power.
With two wheels that freely traverse on the window surface or on wall surface, GlassBot
cleans glass surface efficiently by the intelligent AI-technology path calculation. As well, it
can be manually operated to clean under different modes from the remote control.
Specifications
Input Voltage: AC110-240V
Dimension: 29*14*11.5cm
Net Weight: 0.95KG
Input Voltage:
AC100~240V, 50/60Hz Adaptor;
24V, 80W, 5.5m Cable
Safe Standby Power:
Built-in Li-ion battery, 600mAh 14.8V
Charging Time: 1hour
Features
►
For glasses thicker than 6mm
►
AI Technology
►
Cleaning speed: 4minutes/meter^2.
►
4 kinds of automatic operation modes for cleaning entire window
►
Auto-finish.
►
Embedded UPS (Un-interrupted Power System)
►
Anti-dropping control algorithm
►
Auto detect edges of window
►
Micro-fiber cloth
►
High strength safety rope (150Kgf)
►
Remote control
►
Table cleaning mode
What’s in the package?
Cleaner x 1 pcs
Cleaning cloth x 12 pcs
Remote controller x 1 pcs
Adapter (100~240VAC, 50~60Hz) x 1
AC power cord x 1 pcs
DC power extension cable (4 meter) x 1
Cleaning ring x 4
Safety rope x 1
►
APP Control through IOS/Android system
3
User Manual x 1
Know Y
our GlassBot
Top View
4
①
②
⑤
⑥
⑦
⑧
③
④
Air Vent
Hooking Hole
Buzzer
Know Your GlassBot
T
he
device can be remote controlled from the front and backside.
Remote Control
Au
toma
tically m
ove up
then down
Manually move up
Au
tomatically move left
then down
Manually move down
Au
tomatically move
right then down
Manuall
y move
right
Stop Cleaning
Manually move left
B
A
START
STOP
Plug in
Tighten
the
screw
Please remove the insulation spacer in the bottom of back of remote controller
before useing. If you have to replace the battery, just pull down the battery cover.
Auto Up then Down Auto Left then Down Auto Right then Down
Stop Cleaning
5
Start
Start Cleaning
Before Using
►
The robot shall always connect power cable for normal using.
►
How to put the robot onto glass to start using?
(1) Turn on power-switch, and then make sure the fan is running.
(2) Put device onto glass and keep 10cm away from the window frame.
(3) Check if device can stick to the glass before releasing it.
►
How to take device down from glass?
(1) While device is running, please hold safety rope with one hand and take device
down
from glass with the other hand.
(2) Turn off power-switch in safe area.
►
Safety rope and buckle
(1) Before using, check if the safety rope is broken or the knot is loose.
(2) Fasten the safety rope and tie to indoor fixture before operating.
►
UPS (Un-interrupted Power System) function
(1) The UPS function will be enabled automatically when no electric power supplied. The
backup time of this UPS is 30 minutes.
(2) If no electric power is supplied, the device will stop automatically, alert and flash red
lamp. User shall take device down from the glass as soon as possible.
(3) User can pull device back by pulling safety rope. Slightly pull the safety rope at an
angle close to the glass to prevent dropping.
►
Please make sure the battery was full-charged (green lamp ON) before using
(1) First, turn off the power-switch on the device. Plug in the power. Orange lamp ON
means charging.
(2) Green lamp ON means the battery was full-charged.
►
Table cleaning mode
Put device on the table and select auto-cleaning mode, the device will run in
table-cleaning mode.
►
Notice
(1) Do not use it on frameless glass.
(2) Make sure put cleaning ring onto cleaning wheel correctly for no leakage.
(3) Do not use it in rainy or moist day.
(4) Set danger-warning area downstairs for no-balcony window and door.
How to Clean the Glass
Step I: Use ONLY clean-and-dry cleaning cloth to clean dust and sand on the glass.
Step II: Change again the cleaning cloth. Keep upper wheel’s cleaning cloth as
clean-and-dry. Spray a little detergent (1~2 spray) on lower wheel’s cleaning cloth, but
not make cloth wet (if too wet, the machine can’t move well). Then clean the glass again.
6
Power Adapter/DC Extension Cable
Using/Changing the Cleaning Cloth
1. Put clean-and-dry cleaning cloth onto cleaning ring.
2. Put the cleaning ring onto clean wheel and ensure the 6 slots on the ring are well
fixed with the cleaner wheel to avoid air leakage.
Frequently Asked Questions (FAQ)
Q1: If Robot can’t startup and alert at the beginning of self-test.
Ans: It means that the friction factor is not properly used. Please check:
(1) Whether the cleaning cloth is too dirty.
(2) Glass stickers, window film on the glass will also affect the friction factor.
(3) If clean window many times, the glass surface will become very slippery.
(4) The glass surface will become slippery if clean several times in low humidity
environment such as in air-conditioned rooms.
Power adapter
Plug into DC power jack
L-shape connector
DC extension cable
DC plug
7
Q2: Robot slips and cannot detect
the upper frame of window in “Auto Up then Down”
mode
Ans: Press key and switch to or mode to continue cleaning.
Q3: Robot cannot finish whole window and stop at middle area.
Ans: Press or mode to continue cleaning.
Q4: Robot slips and cannot get higher to the window frame.
Ans:
(1) Friction factor is too low that might be caused by glass stickers, window film on the
glass.
(2) Cleaning cloth might be too wet.
(3) If clean window many times, the glass surface will become very slippery.
(4) The glass surface will become slippery if clean several times in low humidity
environment such as in air-conditioned room.
(5) When startup (press , or or ), keep 10cm away from the window
frame.
Q5: Robot does not move smoothly or moves irregularly.
Ans:
(1) Cleaning cloth is too dirty. Please change the cleaning cloth.
(2) Glass surface has different friction factor areas due to stickers, window film, and son
on. Please use it in single area.
(3) The screw of cleaning wheel might be loose, please tighten it.
Q6: Af
ter cleaning, remained circle mark on the glass surface.
Ans: Cleaning cloth is too dirty. Please change the cleaning cloth and clean for the
second time.
Q7: What to do if robot stopped at higher area while no electric power supplied, it alarms
and red lamp flashes?
Ans:
(1) User can pull robot back with safety rope. Slightly pull the safety rope at an angle close
to the glass to prevent dropping.
(2) Switch the power-switch to “off” status.
(3) Check whether electric poor-contact, or cable broken.
Q8: What to do if robot abnormally stopped and red lamp keeps flashing, without alarm?
Ans:
8
9
10
CN-X1
Control it with your smart phone
Users can control the cleaner through bluetooth matching to your smart
phone, which is simple and convenient.
※ IOS System:
Requires iOS 7.0 or later. Compatible with iPhone, iPad, and iPod touch.
※ Android System:
Requires Android 4.3 or later, bluetooth 4.0 or later.
I
How to control it through APP ?
1. Connect the robot to power supply and press “Start” to turn it on
The robot has to be turned on so the program can be found and matched to
your smartphone.
2. Turn on your phone’s “bluetooth” (Fig 1)
3. Find Glassbot App and open it on your phone (Fig 2)
4. App is available (Fig 3)
5. Click “Bluetooth search” on your phone, and match it to your phone (Fig 4)
6. Connection successful, you can control it through your phone now (Fig 5)
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5
Loading...