RoboToolz RT-7610-5 User Manual

Electronic Self-Leveling,
5-Beam Level, Square &
Plumb Laser Level

RT-7610-5

Láser auto-nivelante

electrónico

de 5 haces para nivelar,

cuadrar y aplomar

Auto-nivellant, niveau électronique à 5 rayons, Laser pour
aligner et équilibrer

User Guide

Manual Para
El Usuario

Notice D’Emploi

IMPORTANT: These labels are attached to every RT-7610-5.
They are not to be removed or defaced.

CAUTION: Use of controls, adjustments or procedures other than those
specified herein may result in laser radiation exposure. Never stare directly
into beam or view directly with optical instruments.

Do not disassemble or attempt to perform any internal servicing. Repairs or
service to this device are to be performed by authorized service centers only.
Do not aim the laser beams in RT-7610-5 at others.

RT-7610-5 contains a semiconductor laser diode with a wavelength of 635
nanometers. The continuous output of any single beam never exceeds 1.0
milliwatts. RT-7610-5 complies with US FDA performance standards, 21 CFR,
Subchapter J.

AVOID EXPOSURE: Laser radiation is emitted from this aperture.

1. User safety

This symbol is attached to the RT-7610-5
at every aperture.

2. RT-7610-5 features

Power
switch

Front beam

calibration port

Battery access

(depress and give

a quarter turn

counter-

clockwise)

Laser

apertures

Rubber grip and

impact bumper

Side beam

calibration port

(not shown)

Electronic

Self-leveling

5/8"x 11

threaded

insert allows

mounting to a tripod

2.0"

1 1/8"

1 1/2"

1 1/2

The True Measure of a Professional

TM

Toolz, 404 Villa Street, Mountain View, CA 94041

1-800-984-0404 • www.robotoolz.com

P/N 080-0022-03

3. Mounting accessory features

Strap raceways

(use single

strap provided)

Sliding 5/8" x 11 threaded mounting

stud attaches to RT-7610-5

5/8" x 11

threaded inserts

allow for mounting

to a tripod.

Thumbwheel

Introduction

Congratulations! You’ve just purchased a time-saving, precision laser tool of
superior quality. RT-7610-5 is not only precise, but it’s also easy to use.
Simply turn RT-7610-5 on, place it on any surface and the servo mechanism
inside the device takes care of the rest. If placed on a surface which positions
the unit beyond its leveling range indicated in the specifications RT-7610-5’s
5 beams will blink quickly, indicating the need for the device to be reposi­tioned on a more level surface. It’s that simple. So get to work and enjoy the
time-savings which RT-7610-5 provides.

Turning the RT-7610-5 on and off

• To turn RT-7610-5 on, slide the power switch forward to the “O”
position.

• To turn RT-7610-5 off, slide the power switch backward to the “I” posi­tion.

Note: When powering off the RT-7610-5, allow at least a 2 second
interval before powering the unit back on. This is to ensure proper
operation of your laser tool.

Auto-off feature

•

A battery saving Auto-off feature has been incorporated into RT­7610-5 that will shut the device off automatically in 20 minutes
unless overridden. To override the Auto-off feature slide the power
switch forward to the override position and hold for more than 2
seconds and less than 5 seconds. (Note: if held longer than 5
seconds unit enters calibration mode). Once the Auto-off feature
has been overridden, all five lasers will rapidly flash twice for mul­tiple cycles. The device will remain on for eight hours before turn­ing off automatically. To re-enable the Auto-off feature, repeat the
process used to enter the Auto-off process or simply turn the unit
off and back on.

Out-of-level indicator

• The RT-7610-5 is a self-leveling device that is effective only within the
specified range. If the device is not level (within or outside of the
specified range), all five laser beams will blink. If the device is outside
of its self-leveling range for 5 or more minutes, the motors will shut
off and the five laser beams will continue flashing indicating the device
is outside of its self-leveling range and needs to be manually adjust­ed.

4. How to use RT-7610-5

Low battery indicator

• When the battery power becomes low, all five laser beams will blink
slowly, (once per 10 seconds) indicating the need for all four of the bat­teries to be replaced.

Note: RT-7610-5 can be used for up to 5 hours during low battery indica
tion before it will turn off completely .

Using the reflective targets

• The red plastic film used in the targets enhances the laser making the
laser dot much more visible. Tabs on the target allow it to be attached
to a standard tape measure which can then be used as a Storey pole.

Using the laser enhancement glasses

• The red plastic used in the glasses enhances the laser, making the laser
dot more visible. These glasses are particularly useful when using RT­7610-5 outdoors or in brightly lit environments.

Battery replacement

• Turn the slotted screw located at the back of RT-7610-5 in the counter­clockwise direction. This will release the battery cover and provide access
to the batteries. Replace all four batteries, and then return the battery
cover to its original position following the steps illustrated. When the bat­tery cover is in place, give the slotted screw a quarter turn in the clock­wise direction to lock the cover in place.

Note: Alkaline batteries offer the longest battery life when used in this
device.

Sliding mounting stud

• Mount RT-7610-5 to the accessory using the sliding mounting stud

• Use the sliding/rotating action of the sliding mounting stud to:

1. Cantilever RT-7610-5 over the accessory.

2. Rotate RT-7610-5 around the mounting stud to change the loca­tion of any of the three horizontal leveling beams without chang­ing the elevation of the beams.

5/8”-11 Tripod mount

• Use this threaded hole, to mount the RT-7610-5 to a surveyor’s tripod.

5. How to use the mounting accessory

2.0"

1 1/8"

1 1/2"

1 1/2