Robot coupe Blixer 6 V.V. User Manual [ru]

BLIXER 5 Plus

•

BLIXER 5 V.V.

•

BLIXER 6 V.V.

SUMMARY

WARRANTY

IMPORTANT WARNING INTRODUCTION TO YOUR

NEW EMULSIFIER-MIXER BLIXER 5 Plus - BLIXER 5 V.V. BLIXER 6 V.V.

SWITCHING ON THE MACHINE

ADVICE ON ELECTRICAL CONNECTIONS CONTROL PANEL

ASSEMBLY TECHNICAL SPECIFICATIONS

DESCRIPTION AND ADVANTAGES PACKAGING WEIGHT DIMENSIONS WORKING HEIGHT NOISE LEVEL

USES AND EXAMPLES

HYGIENE

CLEANING

MOTOR BASE BOWL BLADE SCRAPER ARM

MAINTENANCE

BLADE SCRAPER ARM MOTOR SEAL

SAFETY

STANDARDS

ELECTRICAL DATA

TECHNICAL DATA

EXPLODED VIEWS ELECTRICAL AND WIRING DIAGRAMS

ROBOT-COUPE S.N

.C., LIMITED WARRANTY

Your new ROBOT-COUPE appliance is warranted to the original buyer for a period of one year from the date of sale if you bought it from ROBOT-COUPE

N.C.

If you bought your ROBOT-COUPE product from a distributor your product is covered by your distributor’s warranty (Please check with your distributor terms and conditions of the warranty).

The ROBOT-COUPE

.N.C

. limited warranty is against defects in material and/or workmanship.

The ROBOT-COUPE

. warranty is given expressly and in lieu of all other warranties, expressed or implied, for merchantability and for fitness toward a particular purpose and constitutes the only warranty made by ROBOT-COUPE

France.

THE FOLLOWING ARE NOT COVERED BY THE ROBOT-COUPE

.N.

WARRANTY:

1 - Damage caused by abuse, misuse, drop-

ping, or other similar damage caused by or resulting from failure to follow assembly, operating, cleaning, user maintenance or storage instructions.

2 - Labour to sharpen and/ or replacements for

blades which have become blunt, chipped or worn after a normal or excessive period of use.

3 - Materials or labour to replace or repair

scratched, stained, chipped, pitted, dented or discoloured surfaces, blades, knives, attachments or accessories.

4 - Any alteration, addition or repair that has

not been carried out by the company or an approved service agency.

5 - Transportation of the appliance to or from an

approved service agency.

6 - Labour charges to install or test new attach-

ments or accessories (i.e., bowls, discs, blades, attachments) which have been arbitrarity replaced.

7 - The cost of changing direction-of-rotation of

three-phase electric motors (Installer is responsible).

8 - SHIPPING DAMAGES. Visible and latent

defects are the responsibility of the freight carrier. The consignee must inform the carrier and consignor immediately, or upon discovery in the case of latent defects. KEEP ALL ORIGINAL CONTAINERS AND PACKING MATERIALS FOR CARRIER INSPECTION.

Neither ROBOT-COUPE

.N.

C. nor its affiliated

companies or any of its distributors, directors, agents, employees, or insurers will be liable for indirect damage, losses, or expenses linked to the appliance or the inability to use it.

WARNING: In order to limit accidents such as electric shocks, personal injury or fire, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your appliance and enable you to use the equipment correctly. Please read these instructions in their entirely and make sure that anyone else who may use the mixer also reads them beforehand.

IMPORTANT WARNING

UNPACKING

• Carefully remove the equipment from the packaging and take out all the boxes or packets containing attachments or specific items.

• WARNING - some of the tools are very sharp e.g. blade, discs... etc.

INSTALLATION

• We recommend you install your machine on a perfectly stable solid base.

CONNECTION

• Always check that your mains supply corresponds to that indicated on the rating plate on the motor unit and that it can take the amperage.

• The machine must be earthed.

• With the three-phased version, always check that the blade rotates in an anti-clockwise direction.

HANDLING

• Always take care when handling the blades or discs - they are very sharp.

ASSEMBLY PROCEDURES

• Follow the various assembly procedures carefully (see page 6) and make sure that all the attachments are correctly positioned.

USE

• Never try to override the locking and safety systems.

• Never introduce any object into the container where the food is being processed.

• Never push the ingredients down with your hand.

• Do not overload the appliance.

• Never switch the appliance on while it is empty.

CLEANING

• As a precaution, always unplung your appliance before cleaning it.

• Always clean the appliance and its attachments at the end of each cycle.

• Never place the motor unit in water.

• For parts made of aluminum alloys, use cleaning fluids suitable for aluminum.

• For plastic parts , do not use detergents that are too alkaline (i.e., containing too much caustic soda or ammonia...)

• Robot-Coupe can in no way be held responsible for the user’s failure to follow the basic rules of cleaning and hygiene.

MAINTENANCE

• Before opening the motor housing, it is absolutely vital unplung the appliance.

• Check the seals and washers regularly and ensure that the safety devices are in good working order.

• It is particularly important to maintain and check the attachments since certain ingredients contain corrosive agents e.g. citric acid.

• Never operate the appliance if the power cord or plug has been damaged in any way or if the appliance fails to work properly or has been damaged in any way.

• Do not hesitate to contact your local Maintenance Department if something appears to be wrong.

KEEP THESE INSTRUCTIONS

IN A SAFE PLACE

WARNING

INTRODUCTION TO YOUR NEW EMULSIFIER-MIXER BLIXER 5 Plus - BLIXER 5 V.V BLIXER 6 V.V.

ROBOT-COUPE has developed a new concept in appliance: the BLIXER

The BLIXER combines the features of two well-known appliances: the cutter and the blender-mixer.

The BLIXER is perfectly geared to professional needs. It can perform any number of tasks which you will soon discover as you use it.

The BLIXER will make it easy to prepare mixed liquid or semi-liquid, raw or cooked meals.

The BLIXER replace the blender which does not give entire satisfaction because of its incapacity to process solid foods.

Thanks to its simple design, all components requiring frequent handling for maintenance or cleaning are easily fitted or removed.

To make things easier for you, this manual gives a breakdown of all the various fitting operations.

This manual contains important information designed to help the user get the most out of their device.

We therefore recommend that you read it carefully before using your machine.

SWITCHING ON THE MACHINE

• ADVICE ON ELECTRICAL CONNNECTIONS

Before plugging in, check that your power supply corresponds to that indicated on the machine’s identification plate.

• THREE PHASE BLIXER 5 Plus

The BLIXER 5 Plus is available with the following motor ratings:

230 x 400 V / 50 Hz / 3

400 V / 50 Hz / 3 220 V / 60 Hz / 3 380 V / 60 Hz / 3

This machine is supplied with a cable to which you simply attach the appropriate electrical plug or isolator for your system. The cable has four wires, one earth wire, plus three phases wires.

If you have a 4-pin plug:

1) Connect the green and yellow earth wire to the earth pin.

2) Connect the three other wires to the remaining pins.

If you have more than 4 pins in the plug, please note the ROBOT-COUPE does not require a neutral wire.

Switch on the empty machine, making sure that the blade is rotating properly in an anti-clockwise direction.

If the blade turns in a clockwise direction, swap over two wires.

GREEN YELLOW is the earth,

DO NOT DISCONNECT

Swap either : the and the

the and the

or the and the

• SINGLE PHASE BLIXER 5 Plus

The BLIXER 5 Plus is available with motor ratings:

230 V/50 Hz / 1

220 V/60 Hz / 1 The machine comes with a single phase plug connected to a power cord.

• SINGLE PHASE BLIXER 5 V.V./BLIXER 6 V.V.

The BLIXER 5 V.V. and BLIXER 6 V.V. are available with motor ratings + variable speed : 230 V/50-60 Hz / 1 The standardized plug must be calibrated to a minimum of 13 amps and preferably 20 amps, if the appliance is used intensively.

• CONTROL PANEL

Red switch = Off switch Green switch = On switch Three phase BLIXER 5 Plus - BLIXER 5 V.V. BLIXER 6 V.V.: Pulse control

Three phase BLIXER 5 Plus: Speed selector = 1.500 or 3.000 rpm.

Single phase BLIXER 5 Plus: One speed 3.000 rpm BLIXER 5 V.V. - BLIXER 6 V.V.: Speed variation from

300 to 3.000 rpm.

ASSEMBLY

1) With the motor base facing you, position the cutter bowl on the motor base.

2) Turn the bowl to the right until it locks.

This appliance must be plugged into an earthed socket (risk of electrocution).

WARNING

1 1

2 3

- A patented blade, an exclusive ROBOT-COUPE

feature, gives perfect result for small or large quantities.

- Central bowl hub specially designed for processing

liquids.

- Tight-sealed lid with scraper arm.

- New blade profile for optimum cutting quality.

- Pulse control for better cutting precision.

- Automatic bowl locking.

- Extremely simple unlocking of bowl by means of a trigger fitted in the handle.

- Lid designed to allow the addition of liquid or ingredients during processing.

- Models BLIXER 5 Plus and BLIXER 5 V.V. are equipped with a slightly serrated blade.

- Model BLIXER 6 V.V. is supplied with an all stainless steel slightly serrated blade knife that is fully removable .

- Flat motor base for easier fitting and cleaning of attachments.

- Model BLIXER 5 Plus (three-phase) is provided with

two speeds1.500 and 3.000 rpm.

- Model BLIXER 5 Plus (single-phase) is provided with one speed of 3.000 rpm.

- Models BLIXER 5 V.V. and BLIXER 6 V.V. are equip- ped with an speed variation which varies between 300 and 3.000 rpm to ensure more flexible use and give a wide range of tasks.

3) Engage the blade on the motor shaft and lower it right to the bottom of the bowl.

Make sure that it is correctly positioned, by rotating it in the bowl.

4) Place the lid on the bowl and rotate to the right until it clicks.

The device is now ready for use.

TECHNICAL SPECIFICATIONS

• DESCRIPTION AND ADVANTAGES

- 5.5-litre stainless steel bowl for models BLIXER 5 Plus and BLIXER 5 V.V.

- 6.5-litre stainless steel bowl for model BLIXER 6 V.V.

• PACKAGING

The packaging for these models has been specially designed to prevent damage occurring in transit.

Details of the contents are clearly marked on the packaging:

- type of device;

- voltage;

- attachments (if any);

- serial number; Dimensions (in mm):

Heigh 580 x Lenght 500 x Width 400

• WEIGHT net weight gross weight

BLIXER 5 Plus 24 kg 26 kg BLIXER 5 V.V. 24 kg 26 kg BLIXER 6 V.V. 26 kg 28 kg

• DIMENSIONS (in mm)

BLIXER 5 Plus

A = 480 C = 280 B = 340 D = 265

BLIXER 5 V.V.

A = 480 C = 280 B = 340 D = 265

BLIXER 6 V.V.

A = 520 C = 280 B = 380 D = 265

• WORKING HEIGHT

We recommend that you position the machine on a stable worktop so that the upper edge of the large feed hopper is at a height of between 1.20 m and 1.30 m.

• NOISE LEVEL

The equivalent continuous sound level when the machine is operating on no-load is less than 70 db (A).

USES AND EXAMPLE

The BLIXER 5 Plus - BLIXER 5 V.V. - BLIXER 6 V.V. will enable you to perform all your cutting tasks in minimum time; we recommend therefore that you keep a close eye on the mixture in order to obtain the desired results.

HYGIENE

At each step of food processing, the machine and attachments must be clean. A certain order when processing foods must be followed. In general, always try to process foods that are least likely to cause cross-contamination first, as illustrated in the following example: 1 - Cooked meat

- Terrines/mousses

- Delicatessen

•

ham

•

smoked ham

•

sausage.

2 - Cheese

•

hard

•

other type. 3 - Vegetables. It is vital that all parts of the machine that come into contact with food are cleaned meticulously, using a detergent/sanitiser, after each processing job.

• WARNING: NEVER USE PURE BLEACH.

Always follow the detergent manufacturers instructions to make up the correct strength of solution; these are normally found on the detergent package, if in doubt contact your detergent supplier or manufacturer.

- If necessary rub well with a soft brush or cloth:

NEVER use a harsh abrasive cleaning pad.

- Allow the detergent/sanitiser to work for the requi-

red length of time.

- Always rinse well.

- Dry well with a soft clean cloth. Only air dry if the

detergent manufacturer recommends it.

CLEANING

HOSPITAL USES:

SPOON FEEDING

• Minced foods: meat, fish... • Vegetable purees

• Mousses: vegetables, fish... • Compotes of stewed fruit

SEMI-LIQUID FEEDING

This simply entails diluting spoon-feeding preparations:

• Minced meat + gravy • Puree + liquid (broth, milk...)

• Soups / creamed soups • Fruit compotes + syrup or water

LIQUID FEEDING (for use via tubes)

• Soups and any preparations that can be liquidized.

RESTAURANTS AND DELICATESSEN USES:

• Butter mixtures: snail butter, salmon butter, anchovie butter…

• Sauces: green sauce, mayonnaise, remoulade, ailloli, emulsify sauces with tomatoes, cream, parsley…

• Grinding: lobster, scampi, seashells...

PHARMACEUTICAL AND CHEMICAL

LABORATORY USES:

• Grinding: herbs, seeds, powders, tablets....

• Mixing: homogeneization of creams, ointments, mixed components, varied ingredients...

• MOTOR BASE

Never immerse the motor base in water. Clean using a damp cloth or sponge.

• BOWL

After removing the lid, remove the bowl from the motor base by pushing the trigger fitted in the handle. Pull up to disengage, leaving the blade in the bowl in order to prevent any spillage when working with liquids.

If the food has a solid consistency, remove the blade and empty the bowl.

Replace the bowl, place the blade back on the shaft and switch on the machine in order to remove any mixture which may have stuck to the blade.

If you wish, you can rinse the bowl by filling it with hot water and switching on for a few minutes.

• BLADE

The stainless steel blade of BLIXER 6 V.V. is easy to dismantle and to clean.

Ensure power supply to machine is disconnected. 1 - Place blade dismantling tool over shaft onto

motor base.

2 - Fit blade onto shaft ensuring it is correctly positio-

ned.

3 - Insert bar into blade cap and turn anti-clock-

wise to dismantle .

When re-assembling do not over tighten.

A - Upper blade with sharp edge away from you. B - Lower blade with sharp edge towards you.

As a precaution, always unplug your appliance before cleaning it (risk of electrocution).

WARNING

+ 15 hidden pages