Robinhood ST7001SLIMA Installation and Operation Guide
1
Description: ROBINHOOD SUPERTUB DBL DRW SLIM
Model Number: ST7001SLIM / 7001SLIMA
Model pictured: ST7001SLIM/ST7001SLIMA
ST7001SLIM
Issue: 2
All dimensions in mm
Model may vary slightly from images pictured
2
Overview
Contents of packaging:
1 x Robinhood Supertub (incl waste system, plug)
1 x Installation kit (incl feet)
1 x Tap ware (incl flexible hoses, support plate, fixing plate, nuts) 2 x Handles, washers and screws.
Pre-installation
Important:
o Please read the entire instructions before installing the laundry tub.
o Ensure the household pipes are thoroughly flushed to remove debris before connecting your laundry tub to
the pipe works. To prevent foreign particles damaging the ceramic cartridge an „in-line‟ filter is
recommended to be installed prior to the mixer.
o Warranty on single lever mixer is void if the in-line filter is not fitted.
o Recommended temperature range 5° to 65°C. Maximum temperature 80°C.
o Maximum pressure 174 PSI (1200 kPa), minimum pressure 10 PSI (70 kPa).
Regulation compliance
Comply with current Drainage and Plumbing Regulations as required by your local authority. Sanitary
plumbing shall only be carried out by a Registered Plumber. All plumbing work must be done in accordance
with local and national building and plumbing codes as applicable. All electrical work must be done in
accordance with local and national electrical codes as applicable. In some instances this product may need to
be earthed.
Determine site
Determine the most suitable position for the laundry tub. It may be used either to the left or right of the
washing machine. Allow 10mm clearance between the units. Mark the position on the floor as reference.
Important safety information
o This Robinhood Supertub is not intended for use by young children or infirm persons without supervision.
o Young children should be supervised to ensure that they do not play with the Robinhood Supertub.
o Do NOT use abrasive household cleaner.
3
Installing the Supertub
Confirm if the washing machine waste inlet needs to be moved from right to left before securing the unit to
the wall. If they do need to be changed see page 6 of these installation instructions.
1. Fit the four adjustable feet supplied to the bottom
of the cabinet and adjust to align with worktop or
washing machine height. Use the lock nut to
secure the feet into position. Tilt laundry tub
slightly to assist with access. Check the top of
the laundry tub with a spirit level to ensure that it
is level and check that the cabinet does not
“rock” confirm that the door operates correctly.
Locknut Bottom of the unit
2. Line up the laundry tub to the installation and confirm enough room, if necessary remove the skirting
board at the require distance 560 mm this will allow the unit to sit flush against the wall. (Check with your
local council for building regulations). Remove the laundry tub away from the wall.
3. Remove the transit cable tie‟s holding the 3 way ball valve in position.
4. Fit the tap ware to the tub using the supplied
fittings. Connect the two flexible hoses onto the
body of the tap ware from the underside; ensure
that the flexible hoses are fitted to the hot and
cold correctly. Hand tightened and then finished
with a quarter turn only.
5. Position the laundry tub and cut the house waste pipe (which should already be installed) to the exact
height. The final height will depend on the waste trap dimensions.
6. Fasten the laundry tub to the wall through any of the holes in the rear flanges. Alternative fastening can
be achieved through the floor. Confirm that the drawers operate correctly.
7. Connect the flexible hoses from the 3 way ball valves to the hot and cold mains wingbacks and connect
the waste system to the laundry tub.
8. Test the laundry tub for leaks. Check the tap ware, washing machine caps and the waste system.
9. Seal the laundry tub to the wall using suitable approved sealant. (Check with your local council for
building regulations).
Hot water
hose only
Loading...