Robinhood RIE3CL9SS Installation Manual

Description: ROBINHOOD ISLAND CANOPY 90CM

Model Numbers: RIE3CL9SS

Issue 1

Product may vary slightly from the picture

Pre-installation

Thank you for purchasing a quality Robinhood
rangehood. Robinhood has a high standard of
quality control and every rangehood is tested
and approved before it leaves the factory

Important:

Please read the entire instructions before installing the rangehood, always switch power off prior to installation.
All electrical work must be done by a registered electrician in accordance with local and national electrical codes
as applicable. For your safety, this product must be earthed.

The power socket must be accessible and enable the end user to isolate the rangehood from the power for the
purpose of internal cleaning or maintenance.

A power outlet should be within 1500mm of the power cord exit from the rangehood.

The canopy hood is not intended for use by persons (including children) with reduced physical, sensory or metal
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety

Children should be supervised to ensure that they do not play with the appliance.

There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances
burning gas or other fuels.

There is a fire risk if cleaning is not carried out in accordance with the instructions. You must read the details
concerning the method and frequency of cleaning.

Do not flambé under the rangehood.

Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from appliances
burning gas or other fuels.

The minimum distance between the hob surface and the lowest part of the rangehood is 600mm. This distance
shall be at least 650mm, if the rangehood is installed over a gas hob. If the instructions for the gas hob specify
a greater distance, this has to be taken into account.

Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air is
fulfilled. If re-circulating, ensure that the side outlet grilles on the upper chimney are not obstructed. Even a
partial obstruction will restrict the efficiency of the rangehood.

Stainless steel is very easily damaged during installation if abraded or knocked by tools. Protect the rangehood
with the cardboard box or plastic bag during installation.

Check the contents of the packaging, check all electrical functions of the canopy before installation.
Canopy is heavy. Please ensure adequate care when installing to prevent personal injury.

CAUTION: Accessible parts may become hot when used with cooking appliances

Pre-installation

•The canopy hood is designed for 2400mm (8ft) and 3000 (10ft) ceilings.

•The chimney is telescopic and is designed for hood installations between 650 to 750mm above the

cooking surface*

•Ascertain the desired installation height of the canopy hood*

•Any installation above 750mm will compromise the extraction performance.

•The air outlet from the motor requires 150mm round ducting which requires 170mm diameter hole

in the ceiling.

*Minimum height from the hob top surface to the underside
face of the rangehood
600mm electric hob
650mm gas hob

Notes:
If the instructions for the gas hob specify a greater distance,
this has to be taken into account.

Any installation above 750mm will compromise performance.

Pre-Installation - continued

Contents of packaging: Typical equipment required:

1 x rangehood electric drill and
screwdriver
1 x packet of fasteners tape measure and spirit level
2 x chimney pieces (upper and lower) step ladder
1 x support frames duct tape (if ducting)
1 x Installation and Operating Instructions jig saw (if ducting)
ladder (if ducting)

Ducting Options

The method of ducting should be carefully considered before installing the rangehood. The
guide below recommends the ducting components to use for all common ducting configurations

- through the top of the home (for the roof and soffit) and through the rear of the home.
150mm round ducting should be used in conjunction with this model rangehood.

Extra lengths and/or bends may be required, depending on the length required and whether
there is any structural material in the way, e.g. rafters.

Please note that this chart is designed as a guide. Please consult Robinhood customer services
if unsure.

For NZ phone [phone] or www.robinhood.co.nz. For AUS phone [phone] or
www.robinhood.com.au.